Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 12 2月, 2015 1 次提交
  3. 20 1月, 2015 1 次提交
  5. 15 1月, 2015 2 次提交
    • T
      vxlan: Group Policy extension · 3511494c
      由 Thomas Graf 提交于 
      Implements supports for the Group Policy VXLAN extension [0] to provide
a lightweight and simple security label mechanism across network peers
based on VXLAN. The security context and associated metadata is mapped
to/from skb->mark. This allows further mapping to a SELinux context
using SECMARK, to implement ACLs directly with nftables, iptables, OVS,
tc, etc.

The group membership is defined by the lower 16 bits of skb->mark, the
upper 16 bits are used for flags.

SELinux allows to manage label to secure local resources. However,
distributed applications require ACLs to implemented across hosts. This
is typically achieved by matching on L2-L4 fields to identify the
original sending host and process on the receiver. On top of that,
netlabel and specifically CIPSO [1] allow to map security contexts to
universal labels.  However, netlabel and CIPSO are relatively complex.
This patch provides a lightweight alternative for overlay network
environments with a trusted underlay. No additional control protocol
is required.

           Host 1:                       Host 2:

      Group A        Group B        Group B     Group A
      +-----+   +-------------+    +-------+   +-----+
      | lxc |   | SELinux CTX |    | httpd |   | VM  |
      +--+--+   +--+----------+    +---+---+   +--+--+
	  \---+---/                     \----+---/
	      |                              |
	  +---+---+                      +---+---+
	  | vxlan |                      | vxlan |
	  +---+---+                      +---+---+
	      +------------------------------+

Backwards compatibility:
A VXLAN-GBP socket can receive standard VXLAN frames and will assign
the default group 0x0000 to such frames. A Linux VXLAN socket will
drop VXLAN-GBP  frames. The extension is therefore disabled by default
and needs to be specifically enabled:

   ip link add [...] type vxlan [...] gbp

In a mixed environment with VXLAN and VXLAN-GBP sockets, the GBP socket
must run on a separate port number.

Examples:
 iptables:
  host1# iptables -I OUTPUT -m owner --uid-owner 101 -j MARK --set-mark 0x200
  host2# iptables -I INPUT -m mark --mark 0x200 -j DROP

 OVS:
  # ovs-ofctl add-flow br0 'in_port=1,actions=load:0x200->NXM_NX_TUN_GBP_ID[],NORMAL'
  # ovs-ofctl add-flow br0 'in_port=2,tun_gbp_id=0x200,actions=drop'

[0] https://tools.ietf.org/html/draft-smith-vxlan-group-policy
[1] http://lwn.net/Articles/204905/Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3511494c
    • T
      vxlan: Remote checksum offload · dfd8645e
      由 Tom Herbert 提交于 
      Add support for remote checksum offload in VXLAN. This uses a
reserved bit to indicate that RCO is being done, and uses the low order
reserved eight bits of the VNI to hold the start and offset values in a
compressed manner.

Start is encoded in the low order seven bits of VNI. This is start >> 1
so that the checksum start offset is 0-254 using even values only.
Checksum offset (transport checksum field) is indicated in the high
order bit in the low order byte of the VNI. If the bit is set, the
checksum field is for UDP (so offset = start + 6), else checksum
field is for TCP (so offset = start + 16). Only TCP and UDP are
supported in this implementation.

Remote checksum offload for VXLAN is described in:

https://tools.ietf.org/html/draft-herbert-vxlan-rco-00

Tested by running 200 TCP_STREAM connections with VXLAN (over IPv4).

With UDP checksums and Remote Checksum Offload
  IPv4
      Client
        11.84% CPU utilization
      Server
        12.96% CPU utilization
      9197 Mbps
  IPv6
      Client
        12.46% CPU utilization
      Server
        14.48% CPU utilization
      8963 Mbps

With UDP checksums, no remote checksum offload
  IPv4
      Client
        15.67% CPU utilization
      Server
        14.83% CPU utilization
      9094 Mbps
  IPv6
      Client
        16.21% CPU utilization
      Server
        14.32% CPU utilization
      9058 Mbps

No UDP checksums
  IPv4
      Client
        15.03% CPU utilization
      Server
        23.09% CPU utilization
      9089 Mbps
  IPv6
      Client
        16.18% CPU utilization
      Server
        26.57% CPU utilization
       8954 Mbps
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      dfd8645e
  7. 03 12月, 2014 2 次提交
  9. 25 11月, 2014 1 次提交
    • M
      ipvlan: Initial check-in of the IPVLAN driver. · 2ad7bf36
      由 Mahesh Bandewar 提交于 
      This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.

This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.

The device operates in two different modes and the difference
in these two modes in primarily in the TX side.

(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.

RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.

(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.

RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.

The devices can be added using the "ip" command from the iproute2
package -

	ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2ad7bf36
  11. 28 10月, 2014 1 次提交
    • K
      bridge: Add support for IEEE 802.11 Proxy ARP · 95850116
      由 Kyeyoon Park 提交于 
      This feature is defined in IEEE Std 802.11-2012, 10.23.13. It allows
the AP devices to keep track of the hardware-address-to-IP-address
mapping of the mobile devices within the WLAN network.

The AP will learn this mapping via observing DHCP, ARP, and NS/NA
frames. When a request for such information is made (i.e. ARP request,
Neighbor Solicitation), the AP will respond on behalf of the
associated mobile device. In the process of doing so, the AP will drop
the multicast request frame that was intended to go out to the wireless
medium.

It was recommended at the LKS workshop to do this implementation in
the bridge layer. vxlan.c is already doing something very similar.
The DHCP snooping code will be added to the userspace application
(hostapd) per the recommendation.

This RFC commit is only for IPv4. A similar approach in the bridge
layer will be taken for IPv6 as well.
Signed-off-by: NKyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      95850116
  13. 30 9月, 2014 1 次提交
    • M
      macvlan: add source mode · 79cf79ab
      由 Michael Braun 提交于 
      This patch adds a new mode of operation to macvlan, called "source".
It allows one to set a list of allowed mac address, which is used
to match against source mac address from received frames on underlying
interface.
This enables creating mac based VLAN associations, instead of standard
port or tag based. The feature is useful to deploy 802.1x mac based
behavior, where drivers of underlying interfaces doesn't allows that.

Configuration is done through the netlink interface using e.g.:
 ip link add link eth0 name macvlan0 type macvlan mode source
 ip link add link eth0 name macvlan1 type macvlan mode source
 ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
 ip link set link dev macvlan0 type macvlan macaddr add 00:22:22:22:22:22
 ip link set link dev macvlan0 type macvlan macaddr add 00:33:33:33:33:33
 ip link set link dev macvlan1 type macvlan macaddr add 00:33:33:33:33:33
 ip link set link dev macvlan1 type macvlan macaddr add 00:44:44:44:44:44

This allows clients with MAC addresses 00:11:11:11:11:11,
00:22:22:22:22:22 to be part of only VLAN associated with macvlan0
interface. Clients with MAC addresses 00:44:44:44:44:44 with only VLAN
associated with macvlan1 interface. And client with MAC address
00:33:33:33:33:33 to be associated with both VLANs.

Based on work of Stefan Gula <steweg@gmail.com>

v8: last version of Stefan Gula for Kernel 3.2.1
v9: rework onto linux-next 2014-03-12 by Michael Braun
    add MACADDR_SET command, enable to configure mac for source mode
    while creating interface
v10:
  - reduce indention level
  - rename source_list to source_entry
  - use aligned 64bit ether address
  - use hash_64 instead of addr[5]
v11:
  - rebase for 3.14 / linux-next 20.04.2014
v12
  - rebase for linux-next 2014-09-25
Signed-off-by: NMichael Braun <michael-dev@fami-braun.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      79cf79ab
  15. 10 9月, 2014 1 次提交
  17. 12 7月, 2014 1 次提交
    • J
      ipv6: addrconf: implement address generation modes · bc91b0f0
      由 Jiri Pirko 提交于 
      This patch introduces a possibility for userspace to set various (so far
two) modes of generating addresses. This is useful for example for
NetworkManager because it can set the mode to NONE and take care of link
local addresses itself. That allow it to have the interface up,
monitoring carrier but still don't have any addresses on it.

One more use-case by Dan Williams:
<quote>
WWAN devices often have their LL address provided by the firmware of the
device, which sometimes refuses to respond to incorrect LL addresses
when doing DHCPv6 or IPv6 ND.  The kernel cannot generate the correct LL
address for two reasons:

1) WWAN pseudo-ethernet interfaces often construct a fake MAC address,
or read a meaningless MAC address from the firmware.  Thus the EUI64 and
the IPv6LL address the kernel assigns will be wrong.  The real LL
address is often retrieved from the firmware with AT or proprietary
commands.

2) WWAN PPP interfaces receive their LL address from IPV6CP, not from
kernel assignments.  Only after IPV6CP has completed do we know the LL
address of the PPP interface and its peer.  But the kernel has already
assigned an incorrect LL address to the interface.

So being able to suppress the kernel LL address generation and assign
the one retrieved from the firmware is less complicated and more robust.
</quote>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      bc91b0f0
  19. 05 6月, 2014 1 次提交
  21. 24 5月, 2014 1 次提交
    • S
      net-next:v4: Add support to configure SR-IOV VF minimum and maximum Tx rate through ip tool. · ed616689
      由 Sucheta Chakraborty 提交于 
      o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ed616689
  23. 01 4月, 2014 1 次提交
  25. 24 1月, 2014 2 次提交
  27. 23 1月, 2014 2 次提交
  29. 18 1月, 2014 1 次提交
  31. 04 1月, 2014 3 次提交
  33. 20 12月, 2013 5 次提交
  35. 18 12月, 2013 5 次提交
  37. 14 12月, 2013 8 次提交