Driver probe currently results in:

WARNING: at drivers/base/core.c:576 device_create_file+0x57/0x7e()
Attribute phy_type: write permission without 'store'
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The C ABI reverses the bitfield fill order when compiled as
little-endian.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The previous fix was still too agressive to meet ieee specs.  Increase
to (14, 10).
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MD5 key lookups on a given TCP socket were being performed
incorrectly. This fix alters parameter inputs to the MD5
lookup function tcp_md5_do_lookup, which is called by functions
tcp_md5_do_add and tcp_md5_do_del. Specifically, the change now
inputs the correct address and address family required to make
a proper lookup.
Signed-off-by: NAydin Arik <aydin.arik@alliedtelesis.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the EEE setup allowing to configure this support
when the link changes.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to some hardware integration issue, CPSW sliver modules requires a
reset across suspend/resume cycle for a successful clock gating to
CPGMAC (CPSW and Davinci MDIO) in AM335x PG1.0.
This issue is fixed in PG2.x, though to support suspend/resume on PG1.0
this reset is required.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netlink_diag.h is in include/uapi/linux but not in the Kbuild necessary
to cause it to be exported by make headers_install.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commits 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration) and
baa70a5c (net: fec: enable pause frame to improve rx prefomance for 1G
network) introduced functionality into the FEC driver which is not
supported on MCF5272. The registers used to implement this functionality
do not exist on MCF5272. Since register defines for MCF5272 are separate
from register defines for other chips, building images for MCF5272 fails
as follows.

fec_main.c: In function 'fec_restart':
fec_main.c:520:8: error: 'FEC_RACC' undeclared (first use in this function)
fec_main.c:585:3: error: 'FEC_R_FIFO_RSEM' undeclared (first use in this function)
fec_main.c:586:3: error: 'FEC_R_FIFO_RSFL' undeclared (first use in this function)
fec_main.c:587:3: error: 'FEC_R_FIFO_RAEM' undeclared (first use in this function)
fec_main.c:588:3: error: 'FEC_R_FIFO_RAFL' undeclared (first use in this function)
fec_main.c:591:3: error: 'FEC_OPD' undeclared (first use in this function)

Adding the missing register defines is not an option, since the registers
do not exist on MCF5272. Disable the added functionality for MCF5272 builds.

Cc: Frank Li <Frank.Li@freescale.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Since my commit 3713b4e3 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.

For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The check introduced by:
	commit 26a41ae6
	Author: stephen hemminger <stephen@networkplumber.org>
	Date:   Mon Jun 17 12:09:58 2013 -0700

	    vxlan: only migrate dynamic FDB entries

was not correct because it is checking flag about type of FDB
entry, rather than the state (dynamic versus static). The confusion
arises because vxlan is reusing values from bridge, and bridge is
reusing values from neighbour table, and easy to get lost in translation.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The usb_8dev hardware has problems on some xhci USB hosts. The driver fails to
read the firmware revision in the probe function. This leads to the following
Oops:

    [ 3356.635912] kernel BUG at net/core/dev.c:5701!

The driver tries to free the netdev, which has already been registered, without
unregistering it.

This patch fixes the problem by unregistering the netdev in the error path.
Reported-by: NMichael Olbrich <m.olbrich@pengutronix.de>
Reviewed-by: NBernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Since some refactoring in 5f5a0115, ndisc_send_redirect called
ndisc_fill_redirect_hdr_option on the wrong skb, leading to data corruption or
in the worst case a panic when the skb_put failed.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

General Queries (the one with the Multicast Address field
set to zero / '::') are supposed to have a Maximum Response Delay
of [Query Response Interval], while for Multicast-Address-Specific
Queries it is [Last Listener Query Interval] - not the other way
round. (see RFC2710, section 7.3+7.8)
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of the push to add 802.1ad server provider tagging support to the
kernel the VLAN features flags were renamed. Unfortunately the kernel name
for the VLAN hardware acceleration features that the kernel shows user space
was included in the rename, which broke ethtool (txvlan and rxvlan options
do not work). This patch restores the original names, i.e. the original ABI.
If we wanted to make clear to users that we are refering to CTAGs we can
always change ethtool's short_name and long_name for these features (for
example something along the lines of txvlan -> txvlan-ctag, tx-vlan-offload ->
tx-vlan-ctag-offload).

Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NFernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

after priv->cpts got allocated then this pointer should check to determine
if the allocation succeeded or not.

Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into wireless

John W. Linville says:

====================
This will probably be the last batch of wireless fixes intended
for 3.10.  Many of these are one- or two-liners, and a couple of
others are mostly relocating existing code to avoid races or to
limit the code to effecting specific hardware, etc.

The mac80211 fixes have a couple of exceptions to the above.
Regarding those, Johannes says:

"Following davem's complaint about my patch, here's a new pull request
w/o the patch he was complaining about, but instead with the const
fix rolled into the fix.

I have a fix for radar detection, one for rate control and a workaround
for broken HT APs which is a regression fix because we didn't rely
on them to be correct before."

Johannes also sends some iwlwifi fixes:

"I picked up Nikolay's patch for the chain noise calibration bug
that seems to have been there forever, a fix from Emmanuel for
setting TX flags on BAR frames and a fix of my own to avoid printing
request_module() errors if the kernel isn't even modular. We also
have our own version of Stanislaw's fix for rate control."

Along with those...

Anderson Lizardo fixes a Bluetooth memory corruption bug when an MTU
value is set to too small of a value.

Arend van Spriel sends a revised brcmsmac bug that fixes a regression
caused by a bad return value in an earlier patch.  He also sends a
brcmfmac fix to avoid an oops when loading the driver at boot.

Daniel Drake fixes a race condition in btmrvl that causes hangs on
suspend for OLPC hardware.

Johan Hedberg adds a check to avoid sending a
HCI_Delete_Stored_Link_Key command to devices that don't support them,
avoiding some scary looking log spam.

Stanislaw Gruszka gives us a fix for iwlegacy to be able to use rates
higher than 1Mb/s on older wireless networks.  He also sends an rt2x00
fix to reinstate older tx power handling behavior for some devices
that didn't work well with the current code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter fixes. They are targeted to the
TCP option targets, that have receive some scrinity in the last week. The
changes are:

* Fix TCPOPTSTRIP, it stopped working in the forward chain as tcp_hdr
  uses skb->transport_header, and we cannot use that in the forwarding
  case, from myself.

* Fix default IPv6 MSS in TCPMSS in case of absence of TCP MSS options,
  from Phil Oester.

* Fix missing fragmentation handling again in TCPMSS, from Phil Oester.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a very simple driver, based on the original vendor
driver that Qualcomm/Atheros published/submitted previously,
but reworked to make the code saner. However, it also lost
a number of features (TSO/GSO, VLAN acceleration and multi-
queue support) in the process, as well as debugging support
features I didn't have any use for. The only thing I left
is checksum offload.

More features can obviously be added, but this seemed like
a good start for having a driver in mainline at all.

Johannes Stezenbach has verified that the driver works on
AR8161, I have a AR8171 myself. The E2200 device ID I found
on github in somebody's repository.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should call __vlan_hwaccel_put_tag() only if the packet
comes from vlan, otherwise VLAN_TAG_PRESENT will always be
added.
Reported-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If skb_clone fails if out of memory then just skip the fanout.

Problem was introduced in 3.10 with:
  commit 6681712d
  Author: David Stevens <dlstevens@us.ibm.com>
  Date:   Fri Mar 15 04:35:51 2013 +0000

    vxlan: generalize forwarding tables
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only migrate dynamic forwarding table entries, don't modify
static entries. If packet received from incorrect source IP address
assume it is an imposter and drop it.

This patch applies only to -net, a different patch would be needed for earlier
kernels since the NTF_SELF flag was introduced with 3.10.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for a packet to arrive during vxlan_stop(), and
have a dynamic entry created. Close this by checking if device
is up.

 CPU1                             CPU2
vxlan_stop
  vxlan_flush
     hash_lock acquired
                                  vxlan_encap_recv
                                     vxlan_snoop
                                        waiting for hash_lock
     hash_lock relased
  vxlan_flush done
                                        hash_lock acquired
                                        vxlan_fdb_create

This is a day-one bug in vxlan goes back to 3.7.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

When you copy some code, you are supposed to read it.  If nothing else,
there's a chance to spot and fix an obvious bug instead of sharing it...

X-Song: "I Got It From Agnes", by Tom Lehrer
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
[ Tom Lehrer? You're dating yourself, Al ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "These are a little later than I planned on since I got caught up with
  handling merges for 3.11 most of the week.

  Another week, another batch of fixes for arm-soc platforms.

  Again, nothing controversial.  A few more than would be ideal, but all
  are valid fixes.  In particular the prima2 panic patch is critical
  since it fixes a problem where multiplatform kernels panic on all but
  prima2 hardware."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: SAMSUNG: pm: Adjust for pinctrl- and DT-enabled platforms
  ARM: prima2: fix incorrect panic usage
  arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
  ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
  ARM: omap3: clock: fix wrong container_of in clock36xx.c
  ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
  ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
  ARM: dts: AM33xx: Fix properties on gpmc node
  arm: omap2: fix AM33xx hwmod infos for UART2
  ARM: OMAP3: Fix iva2_pwrdm settings for 3703

Pull networking fixes from David Miller:

 1) Fix RTNL locking in batman-adv, from Matthias Schiffer.

 2) Don't allow non-passthrough macvlan devices to set NOPROMISC via
    netlink, otherwise we can end up with corrupted promisc counter
    values on the device.  From Michael S Tsirkin.

 3) Fix stmmac driver build with debugging defines enabled, from Dinh
    Nguyen.

 4) Make sure name string we give in socket address in AF_PACKET is NULL
    terminated, from Daniel Borkmann.

 5) Fix leaking of two uninitialized bytes of memory to userspace in
    l2tp, from Guillaume Nault.

 6) Clear IPCB(skb) before tunneling otherwise we touch dangling IP
    options state and crash.  From Saurabh Mohan.

 7) Fix suspend/resume for davinci_mdio by using suspend_late and
    resume_early.  From Mugunthan V N.

 8) Don't tag ip_tunnel_init_net and ip_tunnel_delete_net with
    __net_{init,exit}, they can be called outside of those contexts.
    From Eric Dumazet.

 9) Fix RX length error in sh_eth driver, from Yoshihiro Shimoda.

10) Fix missing sctp_outq initialization in some code paths of SCTP
    stack, from Neil Horman.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
  sctp: fully initialize sctp_outq in sctp_outq_init
  netiucv: Hold rtnl between name allocation and device registration.
  tulip: Properly check dma mapping result
  net: sh_eth: fix incorrect RX length error if R8A7740
  ip_tunnel: remove __net_init/exit from exported functions
  drivers: net: davinci_mdio: restore mdio clk divider in mdio resume
  drivers: net: davinci_mdio: moving mdio resume earlier than cpsw ethernet driver
  net/ipv4: ip_vti clear skb cb before tunneling.
  tg3: Wait for boot code to finish after power on
  l2tp: Fix sendmsg() return value
  l2tp: Fix PPP header erasure and memory leak
  bonding: fix igmp_retrans type and two related races
  bonding: reset master mac on first enslave failure
  packet: packet_getname_spkt: make sure string is always 0-terminated
  net: ethernet: stmicro: stmmac: Fix compile error when STMMAC_XMIT_DEBUG used
  be2net: Fix 32-bit DMA Mask handling
  xen-netback: don't de-reference vif pointer after having called xenvif_put()
  macvlan: don't touch promisc without passthrough
  batman-adv: Don't handle address updates when bla is disabled
  batman-adv: forward late OGMs from best next hop
  ...

Pull powerpc fixes from Benjamin Herrenschmidt:
 "So here are 3 fixes still for 3.10.  Fixes are simple, bugs are nasty
  (though not recent regressions, nasty enough) and all targeted at
  stable"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Fix missing/delayed calls to irq_work
  powerpc: Fix emulation of illegal instructions on PowerNV platform
  powerpc: Fix stack overflow crash in resume_kernel when ftracing

Thanks to commit f91eb62f ("init: scream bloody murder if interrupts
are enabled too early"), "bloody murder" is now being screamed.

With a MIPS OCTEON config, we use on_each_cpu() in our
irq_chip.irq_bus_sync_unlock() function.  This gets called in early as a
result of the time_init() call.  Because the !SMP version of
on_each_cpu() unconditionally enables irqs, we get:

    WARNING: at init/main.c:560 start_kernel+0x250/0x410()
    Interrupts were enabled early
    CPU: 0 PID: 0 Comm: swapper Not tainted 3.10.0-rc5-Cavium-Octeon+ #801
    Call Trace:
      show_stack+0x68/0x80
      warn_slowpath_common+0x78/0xb0
      warn_slowpath_fmt+0x38/0x48
      start_kernel+0x250/0x410

Suggested fix: Do what we already do in the SMP version of
on_each_cpu(), and use local_irq_save/local_irq_restore.  Because we
need a flags variable, make it a static inline to avoid name space
issues.

[ Change from v1: Convert on_each_cpu to a static inline function, add
  #include <linux/irqflags.h> to avoid build breakage on some files.

  on_each_cpu_mask() and on_each_cpu_cond() suffer the same problem as
  on_each_cpu(), but they are not causing !SMP bugs for me, so I will
  defer changing them to a less urgent patch. ]
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull VFS fixes from Al Viro:
 "Several fixes + obvious cleanup (you've missed a couple of open-coded
  can_lookup() back then)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  snd_pcm_link(): fix a leak...
  use can_lookup() instead of direct checks of ->i_op->lookup
  move exit_task_namespaces() outside of exit_notify()
  fput: task_work_add() can fail if the caller has passed exit_task_work()
  ncpfs: fix rmdir returns Device or resource busy

Pull xfs fixes from Ben Myers:
 - Remove noisy warnings about experimental support which spams the logs
 - Add padding to align directory and attr structures correctly
 - Set block number on child buffer on a root btree split
 - Disable verifiers during log recovery for non-CRC filesystems

* tag 'for-linus-v3.10-rc6' of git://oss.sgi.com/xfs/xfs:
  xfs: don't shutdown log recovery on validation errors
  xfs: ensure btree root split sets blkno correctly
  xfs: fix implicit padding in directory and attr CRC formats
  xfs: don't emit v5 superblock warnings on write

Pull char / misc fixes from Greg Kroah-Hartman:
 "Here are some small mei driver fixes for 3.10-rc6 that fix some
  reported problems"

* tag 'char-misc-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: me: clear interrupts on the resume path
  mei: nfc: fix nfc device freeing
  mei: init: Flush scheduled work before resetting the device

Pull USB fixes from Greg Kroah-Hartman:
 "Here are some small USB driver fixes that resolve some reported
  problems for 3.10-rc6

  Nothing major, just 3 USB serial driver fixes, and two chipidea fixes"

* tag 'usb-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: fix id change handling
  usb: chipidea: fix no transceiver case
  USB: pl2303: fix device initialisation at open
  USB: spcp8x5: fix device initialisation at open
  USB: f81232: fix device initialisation at open

When replaying interrupts (as a result of the interrupt occurring
while soft-disabled), in the case of the decrementer, we are exclusively
testing for a pending timer target. However we also use decrementer
interrupts to trigger the new "irq_work", which in this case would
be missed.

This change the logic to force a replay in both cases of a timer
boundary reached and a decrementer interrupt having actually occurred
while disabled. The former test is still useful to catch cases where
a CPU having been hard-disabled for a long time completely misses the
interrupt due to a decrementer rollover.

CC: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>

Normally, the kernel emulates a few instructions that are unimplemented
on some processors (e.g. the old dcba instruction), or privileged (e.g.
mfpvr).  The emulation of unimplemented instructions is currently not
working on the PowerNV platform.  The reason is that on these machines,
unimplemented and illegal instructions cause a hypervisor emulation
assist interrupt, rather than a program interrupt as on older CPUs.
Our vector for the emulation assist interrupt just calls
program_check_exception() directly, without setting the bit in SRR1
that indicates an illegal instruction interrupt.  This fixes it by
making the emulation assist interrupt set that bit before calling
program_check_interrupt().  With this, old programs that use no-longer
implemented instructions such as dcba now work again.

CC: <stable@vger.kernel.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It's possible for us to crash when running with ftrace enabled, eg:

  Bad kernel stack pointer bffffd12 at c00000000000a454
  cpu 0x3: Vector: 300 (Data Access) at [c00000000ffe3d40]
      pc: c00000000000a454: resume_kernel+0x34/0x60
      lr: c00000000000335c: performance_monitor_common+0x15c/0x180
      sp: bffffd12
     msr: 8000000000001032
     dar: bffffd12
   dsisr: 42000000

If we look at current's stack (paca->__current->stack) we see it is
equal to c0000002ecab0000. Our stack is 16K, and comparing to
paca->kstack (c0000002ecab3e30) we can see that we have overflowed our
kernel stack. This leads to us writing over our struct thread_info, and
in this case we have corrupted thread_info->flags and set
_TIF_EMULATE_STACK_STORE.

Dumping the stack we see:

  3:mon> t c0000002ecab0000
  [c0000002ecab0000] c00000000002131c .performance_monitor_exception+0x5c/0x70
  [c0000002ecab0080] c00000000000335c performance_monitor_common+0x15c/0x180
  --- Exception: f01 (Performance Monitor) at c0000000000fb2ec .trace_hardirqs_off+0x1c/0x30
  [c0000002ecab0370] c00000000016fdb0 .trace_graph_entry+0xb0/0x280 (unreliable)
  [c0000002ecab0410] c00000000003d038 .prepare_ftrace_return+0x98/0x130
  [c0000002ecab04b0] c00000000000a920 .ftrace_graph_caller+0x14/0x28
  [c0000002ecab0520] c0000000000d6b58 .idle_cpu+0x18/0x90
  [c0000002ecab05a0] c00000000000a934 .return_to_handler+0x0/0x34
  [c0000002ecab0620] c00000000001e660 .timer_interrupt+0x160/0x300
  [c0000002ecab06d0] c0000000000025dc decrementer_common+0x15c/0x180
  --- Exception: 901 (Decrementer) at c0000000000104d4 .arch_local_irq_restore+0x74/0xa0
  [c0000002ecab09c0] c0000000000fe044 .trace_hardirqs_on+0x14/0x30 (unreliable)
  [c0000002ecab0fb0] c00000000016fe3c .trace_graph_entry+0x13c/0x280
  [c0000002ecab1050] c00000000003d038 .prepare_ftrace_return+0x98/0x130
  [c0000002ecab10f0] c00000000000a920 .ftrace_graph_caller+0x14/0x28
  [c0000002ecab1160] c0000000000161f0 .__ppc64_runlatch_on+0x10/0x40
  [c0000002ecab11d0] c00000000000a934 .return_to_handler+0x0/0x34
  --- Exception: 901 (Decrementer) at c0000000000104d4 .arch_local_irq_restore+0x74/0xa0

  ... and so on

__ppc64_runlatch_on() is called from RUNLATCH_ON in the exception entry
path. At that point the irq state is not consistent, ie. interrupts are
hard disabled (by the exception entry), but the paca soft-enabled flag
may be out of sync.

This leads to the local_irq_restore() in trace_graph_entry() actually
enabling interrupts, which we do not want. Because we have not yet
reprogrammed the decrementer we immediately take another decrementer
exception, and recurse.

The fix is twofold. Firstly make sure we call DISABLE_INTS before
calling RUNLATCH_ON. The badly named DISABLE_INTS actually reconciles
the irq state in the paca with the hardware, making it safe again to
call local_irq_save/restore().

Although that should be sufficient to fix the bug, we also mark the
runlatch routines as notrace. They are called very early in the
exception entry and we are asking for trouble tracing them. They are
also fairly uninteresting and tracing them just adds unnecessary
overhead.

[ This regression was introduced by fe1952fc
  "powerpc: Rework runlatch code" by myself --BenH
]

CC: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

in case when snd_pcm_stream_linked(substream) is true, we end up leaking
group.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

a couple of places got missed back when Linus has introduced that one...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>