Signed-off-by: NRobin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

when requesting a GPIO for the first time, the POLAR setting is not
set to a sane state.  this can lead to indeterminate behavior that
cannot be resolved without an explicit write to the Blackfin port POLAR
register.

when requesting a GPIO for the first time via gpio_request(), the POLAR
setting for the GPIO in question should be set to sane state.  this
should occur if the GPIO has not been allocated in any other way.

some examples:
 - when doing something like "request_irq(); gpio_request();" on the
   same GPIO, the POLAR setting should not be reset.
 - when doing "gpio_request(); gpio_request();" on the same GPIO, the
   POLAR setting should be reset only the first time and not the second.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Blackfin arch: Fix Bug - request lines with peripheral_request_list, but don't get freed with peripheral_free_list

Remove erroneous check_gpio(ident) in peripheral_free()
Reported-by: NMichael McTernan <mmcternan@airvana.com>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

On BF561 EBIU_SDGCTL bit 31 controls the SDRAM external data
path width, typically set 0 for a 32-bit bus width. On other
Blackfin derivatives this bit should be set by default.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Dmacopy failed in BF537-STAMP when copy from SRAM to SDRAM and kernel
will reboot automatically.

Fixing by doing a SSYNC before mucking with DMA registers
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Commit 05fe478d introduced some
@wbc->nr_to_write breakage.

It made the following changes:
 1. Decrement wbc->nr_to_write instead of nr_to_write
 2. Decrement wbc->nr_to_write _only_ if wbc->sync_mode == WB_SYNC_NONE
 3. If synced nr_to_write pages, stop only if if wbc->sync_mode ==
    WB_SYNC_NONE, otherwise keep going.

However, according to the commit message, the intention was to only make
change 3.  Change 1 is a bug.  Change 2 does not seem to be necessary,
and it breaks UBIFS expectations, so if needed, it should be done
separately later.  And change 2 does not seem to be documented in the
commit message.

This patch does the following:
 1. Undo changes 1 and 2
 2. Add a comment explaining change 3 (it very useful to have comments
    in _code_, not only in the commit).
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: NNick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The @fnac.net will be shut down within a couple of months, so fix my
email address.
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: remove fast unmounting
  UBIFS: return sensible error codes
  UBIFS: remount ro fixes
  UBIFS: spelling fix 'date' -> 'data'
  UBIFS: sync wbufs after syncing inodes and pages
  UBIFS: fix LPT out-of-space bug (again)
  UBIFS: fix no_chk_data_crc
  UBIFS: fix assertions
  UBIFS: ensure orphan area head is initialized
  UBIFS: always clean up GC LEB space
  UBIFS: add re-mount debugging checks
  UBIFS: fix LEB list freeing
  UBIFS: simplify locking
  UBIFS: document dark_wm and dead_wm better
  UBIFS: do not treat all data as short term
  UBIFS: constify operations
  UBIFS: do not commit twice

* master.kernel.org:/home/rmk/linux-2.6-arm:
  NVRAM depends on RTC_DRV_CMOS
  rename platform_driver name "flash" to "sa1100-mtd"
  annotate that [fp, #-4] is the saved lr
  Use __SPIN_LOCK_UNLOCKED to initialize bad_irq_desc.lock
  ARM: OMAP: fix fault in enter_full_retention()
  ARM: OMAP: Mask interrupts when disabling interrupts, v2
  ARM: OMAP: gptimer min_delta_ns corrected
  ARM: OMAP: Fix hsmmc init, v2
  ARM: OMAP: Fix omap34xx revision detection for ES3.1
  ARM: OMAP: DMA: Fix uninitialized channel flags
  ARM: OMAP: Fix race in OMAP2/3 DMA IRQ handling
  ARM: OMAP: Fix McBSP spin_lock deadlock
  [ARM] 5366/1: fix shared memory coherency with VIVT L1 + L2 caches
  [ARM] call undefined instruction exception handler with irqs enabled
  [ARM] msm: fix build errors
  [ARM] etherh: continue fixing build failure

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
  ocfs2: add quota call to ocfs2_remove_btree_range()
  ocfs2: Wakeup the downconvert thread after a successful cancel convert
  ocfs2: Access the xattr bucket only before modifying it.
  configfs: Silence lockdep on mkdir(), rmdir() and configfs_depend_item()
  ocfs2: Fix possible deadlock in ocfs2_write_dquot()
  ocfs2: Push out dropping of dentry lock to ocfs2_wq

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  [XFS] Warn on transaction in flight on read-only remount
  xfs: Check buffer lengths in log recovery
  don't reallocate sxp variable passed into xfs_swapext

Till VFS can correctly support read-only remount without racing,
use WARN_ON instead of BUG_ON on detecting transaction in flight
after quiescing filesystem.
Signed-off-by: NFelix Blyakher <felixb@sgi.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>

Before trying to obtain, read or write a buffer,
check that the buffer length is actually valid. If
it is not valid, then something read in the recovery
process has been corrupted and we should abort
recovery.
Reported-by: NEric Sesterhenn <snakebyte@gmx.de>
Tested-by: NEric Sesterhenn <snakebyte@gmx.de>
Reviewed-by: NChristoph Hellwig <hch@infradead.org>
Reviewed-by: NFelix Blyakher <felixb@sgi.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>
Signed-off-by: NFelix Blyakher <felixb@sgi.com>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into for-linus

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: implement HORKAGE_1_5_GBPS and apply it to WD My Book
  libata: add no penalty retry request for EH device handling routines
  libata: improve probe failure handling
  libata: add @spd_limit to sata_down_spd_limit()
  libata: clear dev->ering in smarter way
  libata: check onlineness before using SPD in sata_down_spd_limit()
  libata: move ata_dev_disable() to libata-eh.c
  libata: fix EH device failure handling
  sata_nv: ck804 has borked hardreset too
  ide/libata: fix ata_id_is_cfa() (take 4)
  libata: fix kernel-doc warnings
  ahci: add a module parameter to ignore the SSS flags for async scanning
  sata_mv: Fix chip type for Hightpoint RocketRaid 1740/1742
  [libata] sata_sil: Fix compilation error with libata debugging enabled

3Gbps is often much more prone to transmission failures.  It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them.  Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.

This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.

Please take a look at the following bz for related reports.

  http://bugzilla.kernel.org/show_bug.cgi?id=9913Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Let -EAGAIN from EH device handling routines trigger EH retry without
consuming its tries count.  This will be used to implement link SPD
horkage which requires hardreset to adjust SPD without affecting other
EH decisions.  As it bypasses the forward progress guarantee provided
by the tries count, the requester is responsible for ensuring forward
progress.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When link is flaky at high speed, it isn't uncommon for a device to
repeatedly fail probing sequence early after successfully negotiating
high link speed.  This often leads to consecutive hotplug events
without successful probing.

This patch improves libata EH such that it remembers probing trials
and if there have been more than two unsuccessful trials in the past
60 seconds, slows down link speed to 1.5Gbps.

As link speed negotiation is the duty of the PHY layer proper, the
goal of this fallback mechanism is to provide the last resort when
everything else fails, which unfortunately happens not too
infrequently, so no fancy 6->3->1.5 speeding down or highest
successful transmission speed seen kind of logics (yet).
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants.  This parameter doesn't get in the way even
when it's too low.  The closest possible limit is applied.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events.  This patch
achieves this by doing the following.

* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
  clear between BEGIN and END.  ering is moved after END.  The split
  of persistent area is to allow hotter items remain at the head.

* ering is explicitly cleared on ata_dev_disable() and when device
  attach succeeds.  So, ering is persistent throug a device's life
  time (unless explicitly cleared of course) and also through periods
  inbetween disablement of an attached device and successful detection
  of the next one.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

sata_down_spd_limit() should check whether the link is online before
using the SPD value to determine how to limit the link speed.  Factor
out onlineness test and test it from sata_down_spd_limit().
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ata_dev_disable() is about to be more tightly integrated into EH
logic.  Move it to libata-eh.c.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The dev->pio_mode > XFER_PIO_0 test is there to avoid unnecessary
speed down warning messages but it accidentally disabled SATA link spd
down during configuration phase after reset where PIO mode is always
zero.

This patch fixes the problem by moving the test where it belongs.
This makes libata probing sequence behave better when the connection
is flaky at higher link speeds which isn't too uncommon for eSATA
devices.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

While playing with nvraid, I found out that rmmoding and insmoding
often trigger hardreset failure on the first port (the second one was
always okay).  Seriously, how diverse can you get with hardreset
behaviors?  Anyways, make ck804 use noclassify variant too.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

When checking for the CFA feature set support, ata_id_is_cfa() tests bit 2 in
word 82 of the identify data instead the word 83;  it also checks the ATA/PI
version support in the word 80 (which the CompactFlash specifications have as
reserved), this having no slightest chance to work on the modern CF cards that
don't have 0x848A in the word 0...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix libata kernel-doc warnings:

Warning(linux-next-20090120//drivers/ata/libata-core.c:4720): Excess function parameter 'dev' description in 'ata_qc_new'
Warning(linux-next-20090120//drivers/ata/libata-scsi.c:428): No description found for parameter 'ap'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The SSS flag, which directs the OS to spin up one disk at a time
to not have the PSU blow out, sometimes gets set even when not needed.
The effect of this is a longer-than-needed boot time.

This patch adds a module parameter that makes the driver ignore SSS
at least as far as the parallel scan during boot is concerned...
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix chip type for the Highpoint RocketRAID 1740 and 1742 PCI cards.
These really do have Marvell 6042 chips on them, rather than the 5081 chip.

Confirmed by multiple (two) users (for the 1740), and by examining
the product photographs from Highpoint's web site.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

I tried compiling 2.6.29-rc1 and 2.6.29-rc3 with libata debugging enabled
and got the following error:

  CC [M]  drivers/ata/sata_sil.o
drivers/ata/sata_sil.c: In function 'sil_fill_sg':
drivers/ata/sata_sil.c:327: error: 'pi' undeclared (first use in this function)
drivers/ata/sata_sil.c:327: error: (Each undeclared identifier is reported only once
drivers/ata/sata_sil.c:327: error: for each function it appears in.)
make[2]: *** [drivers/ata/sata_sil.o] Error 1
make[1]: *** [drivers/ata] Error 2
make: *** [drivers] Error 2

include/linux/libata.h has the following enabled:

#define ATA_DEBUG
#define ATA_VERBOSE_DEBUG
#define ATA_IRQ_TRAP

This fixes the compilation.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI hotplug: Change link order of pciehp & acpiphp
  PCI hotplug: fakephp: Allocate PCI resources before adding the device
  PCI MSI: Fix undefined shift by 32
  PCI PM: Do not wait for buses in B2 or B3 during resume
  PCI PM: Power up devices before restoring their state
  PCI PM: Fix hibernation breakage on EeePC 701
  PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
  PCI PM: Fix suspend error paths and testing facility breakage

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: fix per cpu kmem_cache_cpu array memory leak
  kmalloc: return NULL instead of link failure

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
  powerpc: Fix oops on some machines due to incorrect pr_debug()
  powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
  powerpc/5200: update device tree binding documentation
  powerpc/5200: Bugfix for PCI mapping of memory and IMMR
  powerpc/5200: update defconfigs

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched_rt: don't use first_cpu on cpumask created with cpumask_and
  sched: fix buddie group latency
  sched: clear buddies more aggressively
  sched: symmetric sync vs avg_overlap
  sched: fix sync wakeups
  cpuset: fix possible deadlock in async_rebuild_sched_domains

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (45 commits)
  V4L/DVB (10411): s5h1409: Perform s5h1409 soft reset after tuning
  V4L/DVB (10403): saa7134-alsa: saa7130 doesn't support digital audio
  V4L/DVB (10229): ivtv: fix memory leak
  V4L/DVB (10385): gspca - main: Fix memory leak when USB disconnection while streaming.
  V4L/DVB (10325): em28xx: Fix for fail to submit URB with IRQs and Pre-emption Disabled
  V4L/DVB (10317): radio-mr800: fix radio->muted and radio->stereo
  V4L/DVB (10314): cx25840: ignore TUNER_SET_CONFIG in the command callback.
  V4L/DVB (10288): af9015: bug fix: stick does not work always when plugged
  V4L/DVB (10287): af9015: fix second FE
  V4L/DVB (10270): saa7146: fix unbalanced mutex_lock/unlock
  V4L/DVB (10265): budget.c driver: Kernel oops: "BUG: unable to handle kernel paging request at ffffffff
  V4L/DVB (10261): em28xx: fix kernel panic on audio shutdown
  V4L/DVB (10257): em28xx: Fix for KWorld 330U Board
  V4L/DVB (10256): em28xx: Fix for KWorld 330U AC97
  V4L/DVB (10254): em28xx: Fix audio URB transfer buffer race condition
  V4L/DVB (10250): cx25840: fix regression: fw not loaded on first use
  V4L/DVB (10248): v4l-dvb: fix a bunch of compile warnings.
  V4L/DVB (10243): em28xx: fix compile warning
  V4L/DVB (10240): Fix obvious swapped names in v4l2_subdev logic
  V4L/DVB (10233): [PATCH] Terratec Cinergy DT XS Diversity new USB ID (0ccd:0081)
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  pxamci: enable DMA for write ops after CMD/RESP
  pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
  ricoh_mmc: Use suspend_late/resume_early
  mmci: Add support for ST Micro derivate
  mmc: Add a MX2/MX3 specific SDHC driver

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  icside: fix PCB version 6 support (v2)
  tx4939ide: typo fix and minor cleanup
  ide: add CS5536 host driver (v3)
  ide: Force VIA IDE legacy interrupts for AmigaOne boards
  IDE: Unregister and disable devices if initialization fails.
  ide: fix ide_register_port() failure handling
  ide: struct device - replace bus_id with dev_name(), dev_set_name()
  ide-cd: fix DMA for non bio-backed requests