Make it clearer how these packets work.
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

vega10 is the only soc15 asic at the moment so these
warnings are invalid, but add a default case to silence
the warnings.

Fixes: 220ab9bd: "drm/amdgpu: soc15 enable (v3)"
Reviewed-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

On KB, KV, CZ we should read the vram width from integrated system
table, if we can. The NOOFCHAN in MC_SHARED_CHMAP is not accurate.

With this change we can enable two 4k displays on CZ again. This use
case was broken sometime in January when we started looking at
vram_width for bandwidth calculations instead of hardcoding this value.

v2:
  Return 0 if integrated system info table is not available.
Tested-by: NRoman Li <roman.li@amd.com>
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

break it out from the check parameters function.
Signed-off-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We accidentally dereference "cb" if the kmalloc() fails.

Fixes: 451bc8eb ("drm/amdgpu: fix PRT teardown on VM fini v3")
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We should return unlock on the error path in pp_dpm_dispatch_tasks()
and there is a double lock bug in pp_dpm_set_sclk_od().

Fixes: 2a507105 ("drm/amd/powerplay: add global PowerPlay mutex.")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This switch statement is missing breaks.

v2: agd: break in default case as well

Fixes: 2a507105 ("drm/amd/powerplay: add global PowerPlay mutex.")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Continuing if the GPU fails to resume will end in pain.
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This only makes a difference for 32-bit systems. The idea is to have a
fixed virtual address space size with 4-level page tables and to
minimize differences between 32 and 64-bit systems.

v2: Update commit message.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

drivers/gpu/drm/amd/amdgpu/amdgpu_psp.c:133:2-3: Unneeded semicolon

 Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci
Acked-by: NHuang Rui <ray.huang@amd.com>
CC: Huang Rui <ray.huang@amd.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fixes: 2a507105 ("drm/amd/powerplay: add global PowerPlay mutex.")
Reported-by: NJulia Lawall <julia.lawall@lip6.fr>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

omapdrm changes for 4.12

Main changes include:

* Add support for render nodes.
* Refactor omapdss code to allow multiple DISPC implementations. This is pre-work for DSS6 support.
* Fix replication logic bug, which caused RGB565 fb to be shown too dark on a 24bit display.
* Improve detection of display stack readiness, which should remove the probe order issues.
* Link panel-dpi with its backlight, so that they are turned on/off in sync.
* Fix possibly incorrect setup of sync and data-enable signals.
* Get rid of DRM_OMAP_NUM_CRTCS config option.

* tag 'omapdrm-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (34 commits)
  drm/omap: Major omap_modeset_init() cleanup
  drm/omap: Remove the obsolete #define omap_plane _omap_plane hack
  drm/omap: Fix one ugly indentation style break left by coccinelle
  drm/omap: Rename enum omap_plane to enum omap_plane_id
  drm/omap: Get rid of DRM_OMAP_NUM_CRTCS config option
  drm/omap: fix crash on module unload
  drm/omap: use drm_atomic_helper_shutdown()
  drm/omap: fix display SYNC/DE flags
  drm/omap: dispc: improve debug print of display flags
  drm/omap: displays: panel-dpi: Support for handling backlight devices
  drm/omap: poll only connectors where the connect/disconnect can be checked
  drm/omap: display: Add displays in sorted order to the panel_list
  drm/omap: Use omapdss_stack_is_ready() to check that the display stack is up
  drm/omap: dss: Support for detecting display stack readiness
  drm/omap: dss: Functions to check components in the display/output list
  drm/omap: fix replication logic
  drm/omap: remove unused dispc_wb_enable & dispc_wb_is_enabled
  drm/omap: remove all EXPORT_SYMBOLs from dispc.c
  drm/omap: use dispc_ops
  drm/omap: fill dispc_ops
  ...

Cleanup overly complex omap_modeset_init(). The function is trying to
support many unusual configuration, that have never been tested and
are not supported by other parts of the dirver.

After cleanup the init function creates exactly one connector,
encoder, crtc, and primary plane per each connected dss-device. Each
connector->encoder->crtc chain is expected to be separate and each
crtc is connect to a single dss-channel. If the configuration does not
match the expectations or exceeds the available resources, the
configuration is rejected.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove the obsolete "#define omap_plane _omap_plane" hack and other
related hacks to get around the enum omap_plane colliding with struct
omap_plane.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Fix one ugly indentation style break left by the previous coccilnelle
patch.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The enum omap_plane conflicted with the same struct name for omapdrm
plane private data. This rename should solve the conflict.

The rename was implement with this very simple coccinelle patch:
------------------------
@@
@@
enum
-omap_plane
+omap_plane_id
------------------------
The patch was applied like this:
spatch --sp-file <cocci_file> --all-includes --in-place --dir drivers/gpu/drm/omapdrm

The above patch did not rename the actual enum definition. That was
added manually on top of the spatch changes.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Allocate one CRTC for each connected output and get rid of
DRM_OMAP_NUM_CRTCS config option. We still can not create more CRTCs
than we have DSS display managers. We also reserve one overlay per
CRTC for primary plane so we can not have more CRTCs than we have
overlays either.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When unloading omapdrm we get a NULL pointer deref in
omap_drm_irq_uninstall(). This is caused by:

967dd484 ("drm: remove
drm_vblank_no_hw_counter assignment from driver code")

We shut down all the crtcs at unload time before calling
omap_drm_irq_uninstall, so the code in omap_drm_irq_uninstall() is
unnecessary and can be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Use drm_atomic_helper_shutdown() to ensure that all crtcs are disabled
when unloading the driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

At the moment VSYNC/HSYNC/DE high/low flags set by the panel/encoder
drivers get lost when the videotimings are translated to DRM's
videomode, as DRM's mode does not have corresponding flags.

DRM has bus-flags for this purpose, and while it lacks a few flags at
the moment, it should be used here. However, until we rewrite omapdrm's
device model, using bus-flags is rather difficult.

As a short term fix, this patch makes sure that every time the videomode
is set in omap_crtc_mode_set_nofb(), the driver asks for the SYNC/DE
flags from the panel/encoder drivers, and thus we get the correct flags
into use.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Instead of printing 0/1 for display flags like vsync high/low, use a
tri-state print (-1/0/1) to indicate the "undefined" state.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The associated backlight device can be configured via DT by providing the
phandle to the device.

If the backlight device is configured, the driver can manage the backligt
along with the panel's power state, iow it can turn on the backlight when
the panel is enabled and turn it off when the panel is disabled.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When the connector associated detect callback is not provided, we can not
detect if the display is connected or disconnected. These displays do not
support hot plug, they are always connected. Let DRM know that connectors
w/o detect callback should not be polled.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Keep the panel_list ordered according to aliases. The DRM connectors will
be created following the panel_list. By keeping the list ordered the DRM
connectors will be created in the same order regardless of the driver
probe order.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Instead of 'guessing' based on aliases of the status of the DSS drivers,
use the new interface to check that all needed drivers are loaded.
In this way we can be sure that all needed drivers are loaded so it is
safe to continue the probing of omapdrm.
This method will allow the omapdrm to be probed 'headless', without
outputs.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When omapdss is loaded (all core components are in place) create a list of
devices used in the display graph. This list later can be used by omapdrm
via the omapdss_stack_is_ready() function to check that these components
are loaded. Based on this information, omapdrm can defer probe in case when
the omapdss stack is not ready yet.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The functions can be used to check a component (by it's of_node) if it is
part of the omapdss display or output list. If the component is found, it
means that the driver is loaded.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSS uses "replication logic" to convert color components from smaller
bit widths to bigger bit widths. Without replication logic, the color
component would be shifted and the least significant bits would be left
at 0, whereas with replication logic, the least significat bits will be
filled with the most significant bit.

For some reason omapdrm leaves replication logic always to off, which,
in the most common case, means that showing 16-bit RGB colors on 24-bit
display gives a bit darker colors than expected.

The reset value of the replication logic bit is enabled, and it should
always be set, as there's no practical reason to disable it. This patch
removes the option to disable it from omapdrm, and always sets it to
enabled in dispc.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove two unused WB functions.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdrm now uses dispc_ops instead of direct function calls so we can
remove all EXPORT_SYMBOLs from dispc. Most of the functions can also be
made static, but a few are used outside dispc.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Change omapdrm to get dispc_ops and use that to call the dispc functions
instead or direct function calls.

The change is very straightforward.

The only problem was in omap_crtc_init() which calls pipe2vbl(crtc), and
at that point of time the crtc->dev link, which is used to get the
dispc_ops, has not been set up yet. This patch makes omap_crtc_init()
skip the call to pipe2vbl() and instead calls
dispc_ops->mgr_get_vsync_irq() directly.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch changes the current omapdss driver to fill a dispc_ops struct
and set it to omapdss-base.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We want to change the dispc API from plain functions to a struct with
functions pointers, so that omapdrm can call either omapdss or omapdss6
depending on the platform.

This patch adds 'struct dispc_ops' and adds functions to omapdss-base
to set and get the ops.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdrm still uses a few non-dispc functions: dss_feat_get_num_mgrs(),
dss_feat_get_num_ovls() and  dss_feat_get_supported_color_modes(). We
want to provide omapdrm a single dispc_ops function pointer struct so
that omapdrm will use either the current omapdss or the new omapdss6
driver depending on the platform.

Those three functions are really dispc functions, but are located in the
dss_features.c for legacy reasons.

This patch adds similar functionss to the dispc, and changes omapdrm to
use those new functions. Underneath the functions still call the
functions from dss_feature.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This patch moves the common parts of omapdss to omapdss-base so that
both the current omapdss driver and the new omapdss6 driver can use
them.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

display.c uses dsi_get_pixel_size() which is implemented in the DSI
driver, and we won't have that in the omapdss-base module, to which we
want to move display.c

This patch changes display.c not to use dsi_get_pixel_size(). The call
can be replaced with a simple check for OMAP_DSS_DSI_FMT_RGB565.

We can also make dsi_get_pixel_size() static as it's no longer used
outside dsi.c.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We don't have omapdss's custom error printing functions in the common
omapdss-base module, to which we want to move output.c.

This patch changes output.c to use dev_err instead of DSSERR so that it
doesn't depend on DSSERR.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdss_is_initialized() is used to find out if omapdss has been probed
successfully. This patch moves the related code to the common
omapdss-base module, so that the same support will be there for both
omapdss and omapdss6.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We are working towards enabling omapdss6, which will consists of a new
dss, dispc and dpi drivers. omapdss6 will be a new module. The panel,
encoder and omapdrm will need to use either the current omapdss driver
or the new omapdss6 driver, depending on the platform.

This will be implemented with a common base module and function
pointers.

This patch adds a skeleton omapdss-base.ko module, to which we'll be
moving common dss functionality like registration of the panels.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>