There are some cases in arizona_dev_init, such as where we don't
recognise the chip ID, in which we head to the error path without
setting a sensible error code in ret. This would lead to the chip
silently failing probe, as it would still return 0. Fix this up by
adding appropriate sets of the return value.

Whilst adding these update the existing paths that do return an error
when the chip is not recognised to use ENODEV, which seems like a better
fit.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds common driver for the Top block of the Samsung Exynos
SoC Low Power Audio Subsystem.  This is a minimal driver which prepares
resources for IP blocks like I2S, audio DMA and UART and exposes
a regmap for the Top block registers.  Also system power ops are added
to ensure the Audio Subsystem is operational after system suspend/resume
cycle.
Signed-off-by: NInha Song <ideal.song@samsung.com>
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds documentation of the DT bindings for the Samsung
Exynos SoC Low Power Audio Subsystem.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The function da9052_clear_fault_log() is added to mitigate the case of
persistent data being transferred between reboots.

Clearance of any the persistent information within the DA9053 FAULT_LOG
register must be completed during start-up so the fault-log does not
continue with previous values. A clearance function has been added here in
the kernel driver because wiping the fault-log cannot be counted on outside
the Linux kernel.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: NAdam Thomson <adam.thomson.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Adjust jump targets according to the Linux coding style convention.
Another check for the variable "status" can be omitted then at the end.

Link: https://lkml.kernel.org/g/<20160628163146.GG29166@dell>
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Member "status" of struct usb_sg_request is managed by usb core. A
spin lock is used to serialize the change of it. The driver could
check the value of req->status, but should avoid changing it without
the hold of the spinlock. Otherwise, it could cause race or error
in usb core.

This patch could be backported to stable kernels with version later
than v3.14.

Cc: stable@vger.kernel.org # 3.14+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

probe_irq_on() only returns non-zero if it found any interrupts below
IRQ32 which could be probe candidates.  If all the probable interrupts
are higher than 32, then this will cause a failure.  Fix this.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The MSM8660, APQ8060, IPQ806x and MSM8960 have a GCC clock
to the message RAM used by the RPM. This needs to be enabled
for messages to pass through. This is a crude solution that
simply prepare/enable at probe() and disable/unprepare
at remove(). More elaborate PM is probably possible to
add later.

The construction uses IS_ERR() to gracefully handle the
platforms that do not provide a message RAM clock. It will
bail out of probe only if the clock is hitting a probe
deferral situation.

Of course this requires the proper device tree set-up:

rpm: rpm@104000 {
    compatible = "qcom,rpm-msm8660";
    clocks = <&gcc RPM_MSG_RAM_H_CLK>;
    clock-names = "ram";
    ...
};

I have provided this in the MSM8660 device tree, and will
provide patches for the other targets.

Cc: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact.  The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The lp873x series of PMICs have a bunch of regulators and a couple
of GPO(General Purpose Outputs).
Add information for the MFD and regulator drivers.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The Intel Whiskey Cove PMIC includes several function units, e.g.
ADC, thermal, USB Type-C, GPIO, etc. The corresponding device has
to be created in the mfd driver(intel_soc_pmic_bxtwc.c). This change
adds the USB Type-c device.
Signed-off-by: NBin Gao <bin.gao@intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Intel Kaby Lake PCH-H has the same LPSS than Intel Sunrisepoint. Add the new
IDs to the list of supported devices.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug.  It's done
consistently so it won't cause a problem unless "irq" is more than 4.

Fixes: 70c6cce0 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

It's only used in this driver and never get modified, make it static const.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Reviewed-by: NThor Thayer <tthayer@opensource.altera.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This fixes a compile failure:

	drivers/built-in.o: In function `wm8350_i2c_probe':
	core.c:(.text+0x828b0): undefined reference to `__devm_regmap_init_i2c'
	Makefile:953: recipe for target 'vmlinux' failed

Fixes: 52b461b8 ("mfd: Add regmap cache support for wm8350")
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Remove incorrect e-mail addresses from the copyright header and
MODULE_AUTHOR() macro. These e-mail addresses are no longer in use.

The author names have not been changed, only the e-mail addresses have
been deleted from the source files.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Now that we have a GPIO driver for the AXP209, we can add it to our MFD.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-gpio-4.9', 'ib-mfd-gpio-regulator-4.9', 'ib-mfd-input-4.9', 'ib-mfd-regulator-4.9', 'ib-mfd-regulator-4.9.1', 'ib-mfd-regulator-rtc-4.9', 'ib-mfd-regulator-rtc-4.9-1' and 'ib-mfd-rtc-4.9' into ibs-for-mfd-merged

This patch adds requesting of the clocks supplied on MCLK1, MCLK2 pins,
gating of the 32k clock is added to the arizona_clk32k_enable(),
arizona_clk32k_disable() helpers.

It's a temporary change until the CODEC's clock controller gets exposed
through the clk API and is helpful for board configurations where the
MCLK clocks are not provided by always on oscillators.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.

This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.

This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the basic and regulator bindings for the X-Powers AXP806
PMIC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The X-Powers AXP806 PMIC has a new set of buck and LDO regulators, and
also a switch. The buck regulators support teaming into multi-phase
groups, with A+B, A+B+C, D+E groupings.

Some registers controlling DCDC converter work settings are at different
offsets. Deal with them as well.

Add support for this new variant.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The RK808 and RK818 PMICs are using a similar register map.
We can reuse the rtc driver for the RK818 PMIC. So let's add
the RK818 in the Kconfig description.
Signed-off-by: NWadim Egorov <w.egorov@phytec.de>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add device tree bindings documentation for Rockchip's RK818 PMIC.
Signed-off-by: NWadim Egorov <w.egorov@phytec.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add support for the rk818 regulator. The regulator module consists
of 4 DCDCs, 9 LDOs, 1 switch and 1 BOOST converter which is used to
power OTG and HDMI5V.

The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: NWadim Egorov <w.egorov@phytec.de>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The RK818 chip is a Power Management IC (PMIC) for multimedia and handheld
devices. It contains the following components:

- Regulators
- RTC
- Clocking
- Battery support

Both RK808 and RK818 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Signed-off-by: NWadim Egorov <w.egorov@phytec.de>
Tested-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Change the MFD config option as per latest naming
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add driver for lp873x PMIC family GPOs. Two GPOs are supported
and can be configured in Open-drain output or Push-pull output.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The LP873X chip is a power management IC for Portable Navigation Systems
    and Tablet Computing devices. It contains the following components:

     - Regulators.
     - Configurable General Purpose Output Signals (GPO).

PMIC interacts with the main processor through i2c. PMIC has
couple of LDOs (Linear Regulators), couple of BUCKs (Step-Down DC-DC
Converter Cores) and GPOs (General Purpose Output Signals).
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Because events other that keyboard ones will be handled by now on by
other drivers, stop directly handling interrupts and instead listen to
the new notifier in the MFD driver.
Signed-off-by: NVic Yang <victoryang@google.com>
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Newer revisions of the ChromeOS EC add more events besides the keyboard
ones. So handle interrupts in the MFD driver and let consumers register
for notifications for the events they might care.

To keep backward compatibility, if the EC doesn't support MKBP event, we
fall back to the old MKBP key matrix host command.

Cc: Randall Spangler <rspangler@chromium.org>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: NVic Yang <victoryang@google.com>
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In order to support the Qualcomm MDM9615 SoC, add support for the
PM8018 RPM regulator in the qcom_rpm-regulator driver.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In order to support the Qualcomm MDM9615 SoC, add support for the
RPM regulator entries in the qcom-rpm driver.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In order to support RTC on Qualcomm MDM9615 SoC, add support for
the pm8018 rtc in rtc-pm8xxx driver.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In order to support the Qualcomm MDM9615 PMIC, add support for the
pm8018 in pm8921 MFD driver.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Pull thermal updates from Zhang Rui:

 - Fix a race condition when updating cooling device, which may lead to
   a situation where a thermal governor never updates the cooling
   device.  From Michele Di Giorgio.

 - Fix a zero division error when disabling the forced idle injection
   from the intel powerclamp.  From Petr Mladek.

 - Add suspend/resume callback for intel_pch_thermal thermal driver.
   From Srinivas Pandruvada.

 - Another two fixes for clocking cooling driver and hwmon sysfs I/F.
   From Michele Di Giorgio and Kuninori Morimoto.

[ Hmm.  That suspend/resume callback for intel_pch_thermal doesn't look
  like a fix, but I'm letting it slide..  - Linus ]

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: clock_cooling: Fix missing mutex_init()
  thermal: hwmon: EXPORT_SYMBOL_GPL for thermal hwmon sysfs
  thermal: fix race condition when updating cooling device
  thermal/powerclamp: Prevent division by zero when counting interval
  thermal: intel_pch_thermal: Add suspend/resume callback

Pull m68knommu fix from Greg Ungerer:
 "This contains only a single fix for a register corruption problem on
  certain types of m68k flat format binaries"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: fix user a5 register being overwritten

Merge tag 'fixes-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull h8300 and unicore32 architecture fixes from Guenter Roeck:
 "Two patches to fix h8300 and unicore32 builds.

  unicore32 builds have been broken since v4.6.  The fix has been
  available in -next since March of this year.

  h8300 builds have been broken since the last commit window.  The fix
  has been available in -next since June of this year"

* tag 'fixes-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  h8300: Add missing include file to asm/io.h
  unicore32: mm: Add missing parameter to arch_vma_access_permitted