SMC does not support eyecatchers in RMB elements,
decline peers requesting this support.
Signed-off-by: NKarsten Graul <kgraul@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Process and respond to CONFIRM RKEY and DELETE RKEY messages.
Signed-off-by: NKarsten Graul <kgraul@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add TEST LINK message responses, which also serves as preparation for
support of sockopt TCP_KEEPALIVE.
Signed-off-by: NKarsten Graul <kgraul@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The daddr field holds the destination IPv4 address. The field was set but
never used and can be removed. The addr field was a left-over from an
earlier version of non-blocking connects and can be removed.
The result of the call to kernel_getpeername is not used, the call can be
removed. Non-blocking connects are working, so remove restriction comment.
Signed-off-by: NKarsten Graul <kgraul@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function smc_netinfo_by_tcpsk() belongs to CLC handling.
Move it to smc_clc.c and rename to smc_clc_netinfo_by_tcpsk.
Signed-off-by: NKarsten Graul <kgraul@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove structures used internal only from headers.
And remove an extra function parameter.
Signed-off-by: NStefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
ipmr, ip6mr: Align multicast routing for IPv4 & IPv6

Historically ip6mr was based [cut-n-paste] on ipmr and the two have not
diverged too much. Apparently as ipv4 multicast routing is more common
than its ipv6 brethren modifications since then are mostly one-way,
affecting ipmr while leaving ip6mr unchanged.

This series is meant to re-factor both ipmr and ip6mr into having common
structures [and some functionality], adding 2 new common files -
mroute_base.h and ipmr_base.c.

The series begins by bringing ip6mr up to speed to some of the changes
applied in the past to ipmr [#2, #3].
It is then possible to re-factor a lot of the common structures -
vif devices [#1], mr_table [#4] mfc_cache [#6], and use the common
structures in both ipmr and ip6mr.

The rest of the patches re-factor some choice flows used by both ipmr
and ip6mr and eliminates duplicity.

This series would later allow for easy extension of ipmr offloading
to support ip6mr offloading as well, as almost all structures
related to the offloading would be shared between the two protocols.

Changes from previous versions
------------------------------
v2:
  - #6 Corrected reporting logic when hitting an unresolved cache
  - #7 Addressed kernel doc style [Thanks Nikolay]

RFC -> v1:
  - Corrected support for CONFIG_IP{,V6}_MROUTE_MULTIPLE_TABLES
  - Addressed a couple of kbuild test robot issues
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The various MFC entries are being held in the same kind of mr_tables
for both ipmr and ip6mr, and their traversal logic is identical.
Also, with the exception of the addresses [and other small tidbits]
the major bulk of the nla setting is identical.

Unite as much of the dumping as possible between the two.
Notice this requires creating an mr_table iterator for each, as the
for-each preprocessor macro can't be used by the common logic.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MFC_NOTIFY exists in ip6mr, probably as some legacy code
[was already removed for ipmr in commit
06bd6c03 ("net: ipmr: remove unused MFC_NOTIFY flag and make the flags enum").
Remove it from ip6mr as well, and move the enum into a common file;
Notice MFC_OFFLOAD is currently only used by ipmr.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Same as previously done with the mfc seq, the logic for the vif seq is
refactored to be shared between ipmr and ip6mr.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the exception of the final dump, ipmr and ip6mr have the exact same
seq logic for traversing a given mr_table. Refactor that code and make
it common.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipmr and ip6mr utilize the exact same methods for searching the
hashed resolved connections, difference being only in the construction
of the hash comparison key.

In order to unite the flow, introduce an mr_table operation set that
would contain the protocol specific information required for common
flows, in this case - the hash parameters and a comparison key
representing a (*,*) route.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mfc_cache and mfc6_cache are almost identical - the main difference is
in the origin/group addresses and comparison-key. Make a common
structure encapsulating most of the multicast routing logic  - mr_mfc
and convert both ipmr and ip6mr into using it.

For easy conversion [casting, in this case] mr_mfc has to be the first
field inside every multicast routing abstraction utilizing it.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that both ipmr and ip6mr are using the same mr_table structure,
we can have a common function to allocate & initialize a new instance.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following previous changes to ip6mr, mr_table and mr6_table are
basically the same [up to mr6_table having additional '6' suffixes to
its variable names].
Move the common structure definition into a common header; This
requires renaming all references in ip6mr to variables that had the
distinct suffix.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 8fb472c0 ("ipmr: improve hash scalability") ipmr has
been using rhashtable as a basis for its mfc routes, but ip6mr is
currently still using the old private MFC hash implementation.

Align ip6mr to the current ipmr implementation.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ipmr the mr_table socket is handled under RCU. Introduce the same
for ip6mr.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The two implementations have almost identical structures - vif_device and
mif_device. As a step toward uniforming the mr_tables, eliminate the
mif_device and relocate the vif_device definition into a new common
header file.

Also, introduce a common initializing function for setting most of the
vif_device fields in a new common source file. This requires modifying
the ipv{4,6] Kconfig and ipv4 makefile as we're introducing a new common
config option - CONFIG_IP_MROUTE_COMMON.
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
fib_rules: support sport, dport and proto match

This series extends fib rule match support to include sport, dport
and ip proto match (to complete the 5-tuple match support).
Common use-cases of Policy based routing in the data center require
5-tuple match. The last 2 patches in the series add a call to flow dissect
in the fwd path if required by the installed fib rules (controlled by a flag).

v1:
  - Fix errors reported by kbuild and feedback on RFC
  - extend port match uapi to accomodate port ranges

v2:
  - address comments from Nikolay, David Ahern and Paolo (Thanks!)

Pending things I will submit separate patches for:
  - extack for fib rules
  - fib rules test (as requested by david ahern)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dissect flow in fwd path if fib rules require it. Controlled by
a flag to avoid penatly for the common case. Flag is set when fib
rules with sport, dport and proto match that require flow dissect
are installed. Also passes the dissected hash keys to the multipath
hash function when applicable to avoid dissecting the flow again.
icmp packets will continue to use inner header for hash
calculations.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dissect flow in fwd path if fib rules require it. Controlled by
a flag to avoid penatly for the common case. Flag is set when fib
rules with sport, dport and proto match that require flow dissect
are installed. Also passes the dissected hash keys to the multipath
hash function when applicable to avoid dissecting the flow again.
icmp packets will continue to use inner header for hash
calculations (Thanks to Nikolay Aleksandrov for some review here).
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

support to match on src port, dst port and ip protocol.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

support to match on src port, dst port and ip protocol.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

uapi for ip_proto, sport and dport range match
in fib rules.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of MSI-X the interrupt number may differ from pcidev->irq.
Fix this by using pci_irq_vector().

Fixes: 6c6aa15f ("r8169: improve interrupt handling")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2018-02-28

This series contains updates to fm10k only.

Jake provides all the changes in this series, starting with making the
function header comments consistent and to align with how the kernel
documentation expects it.  Also cleaned up code comment as well as bump
the driver version.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
selftests: forwarding: Add VRF-based tests

One of the nice things about network namespaces is that they allow one
to easily create and test complex environments.

Unfortunately, these namespaces can not be used with actual switching
ASICs, as their ports can not be migrated to other network namespaces
(NETIF_F_NETNS_LOCAL) and most of them probably do not support the
L1-separation provided by namespaces.

However, a similar kind of flexibility can be achieved by using VRFs and
by looping the switch ports together. For example:

                             br0
                              +
               vrf-h1         |           vrf-h2
                 +        +---+----+        +
                 |        |        |        |
    192.0.2.1/24 +        +        +        + 192.0.2.2/24
               swp1     swp2     swp3     swp4
                 +        +        +        +
                 |        |        |        |
                 +--------+        +--------+

The VRFs act as lightweight namespaces representing hosts connected to
the switch.

This approach for testing switch ASICs has several advantages over the
traditional method that requires multiple physical machines, to name a
few:

1. Only the device under test (DUT) is being tested without noise from
other system.

2. Ability to easily provision complex topologies. Testing bridging
between 4-ports LAGs or 8-way ECMP requires many physical links that are
not always available. With the VRF-based approach one merely needs to
loopback more ports.

These tests are written with switch ASICs in mind, but they can be run
on any Linux box using veth pairs to emulate physical loopbacks.

v2:
* Order local variables declaration according to function arguments
  order (Petr)

v1:
* Change location to net/forwarding instead of forwarding/
* Add ability to pause on failure
* Add ability to pause on cleanup
* Make configuration file optional
* Make ping/ping6/mz configurable
* Add more tc tests
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test shared block infrastructure. This is a basic test that shares TC
block in between 2 clsact qdiscs.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tests chains matching and goto chain action.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add first part of actions tests. This patch only contains tests of gact
ok/drop/trap and mirred redirect egress.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add first part of flower tests. This patch only contains dst/src ip/mac
matching.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have one host generate 16K IPv6 echo requests with a random flow label
and check that they are distributed between both multipath links
according to the provided weights.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use different weights for the multipath route configured on the first
router and check that the different flows generated by the first host
are distributed according to the provided weights.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a topology with two hosts, each directly connected to a different
router. Both routers are connected using two links, enabling multipath
routing.

Test IPv4 and IPv6 ping using default MTU and large MTU.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure two hosts which are directly connected to the same router and
test IPv4 and IPv6 ping. Use a large MTU and check that ping is
unaffected.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test cases for unknown unicast and unregistered multicast flooding.

For each traffic type, turn off flooding on one bridged port and inject
a packet of the specified type through the second bridged port. Make
sure the packet was not received by checking the ACL counters on the
other end. Later, turn on flooding and make sure the packet was
received.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Send a packet with a specific destination MAC, make sure it was learned
on the ingress port and then aged-out.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>