Since sg-read is a bidi operation, it is a gain to convert
a single sg entry into a regular read. Better do this in the
generic layer then force each caller to do so.
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Originally, libata required the illusion that it could access the sata
control register.  Now, however, it can run perfectly well without
them, so remove the dummy routines from libsas which tried to emulate
them (but only ended up causing confusion).
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Instead of using a config option for debugging, just dump the
messages with KERN_DEBUG.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

ATAPI check condition needs to be treated the same as a success or
protocol return.  The register returns from the PACKET command are all
correctly positioned in the device to host register FIS and so we
should collect them properly.  Right at the moment this doesn't matter
because libata sends a request sense always for ATAPI errors, but if
it ever checked the registers, we should have the correct contents
just in case.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Previously we were using strncmp in order to avoid having to include
whitespace in the devlist, but this means "HSV1000" matches a device
list entry that says "HSV100", which is wrong.  This patch changes
scsi_dh.c to use scsi_devinfo's matching functions instead, since they
handle these cases correctly.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

For scsi_dh.c to use devinfo lists, we have to be able to remove entries
before rmmod.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

fixed the connection problem when the private iscsi ipv4 address is
provisioned on the interface.
Signed-off-by: NKaren Xie <kxie@chelsio.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

A 'kfree(karg)' is missing in a failure path in
mptctl.c::mptctl_getiocinfo() which can cause a memory leak.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: N"Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The nopout's reserved field was not being initialized to zero
before being reused.  Stale CDB values from previous SCSI cmds
of the same BHS offset was the cause of the disconnection
initiated by the Lefthand target.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Remove gl_skb from cxgbi_ddp_info as it is only used by cxgb3i.
Signed-off-by: NKaren Xie <kxie@chelsio.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

There is no need to set ulpmode on the tx skbs if no digest is enabled.
Signed-off-by: NKaren Xie <kxie@chelsio.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

memset arg64 to zero in the passthrough ioctls to avoid leaking contents
of kernel stack memory to userland via uninitialized padding fields
inserted by the compiler for alignment reasons.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Thanks to Scott Teel for noticing this.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Need to take the lock while accessing the register to check to
see if config table changes have taken effect.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is to prevent hpsa from resetting older boards
which the cciss driver may be controlling.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is to conserve memory in a memory-limited kdump scenario
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

and use the doorbell reset method if available (which doesn't
lock up the controller if you properly save and restore all
the PCI registers that you're supposed to.)
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

After a reset, we should first wait for the board to become "not ready",
and then wait for it to become "ready", instead of immediately
waiting for it to become "ready", and do this waiting *after*
restoring PCI config space registers.  Also, only wait 10 secs
for board to become "not ready" after a reset (it should quickly
become not ready.)
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

They are defined in hpsa_cmd.h
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Some low bits might have been set by the driver, causing
a message like this to come out:

 [   13.288062] ------------[ cut here ]------------
 [   13.293211] WARNING: at lib/dma-debug.c:803 check_unmap+0x1a1/0x654()
 [   13.300387] Hardware name: ProLiant DL180 G6
 [   13.305335] hpsa 0000:06:00.0: DMA-API: device driver tries to free
 DMA memory it has not allocated [device address=0x000000007f81e001]
 [size=640 bytes]
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Currently NetApp's VID/PID details in the INQUIRY response shows up as
'NETAPP' and 'LUN'.  With upcoming scalable SAN ONTAP version on NetApp
controllers, the PID entry alone is being modified to 'LUN C-Mode' (to
distinguish current ONTAP LUNs from scalable ONTAP LUNs).

'LUN' would still suffice for matching 'LUN C-Mode' but best to
explicitly add these new NetApp LUNs to the device list.
Reported-by: NMartin George <marting@netapp.com>
Acked-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Adds Promise VTrak devices to the ALUA device handler.
Signed-off-by: NIlgu Hong <ilgu.hong@promise.com>
Signed-off-by: NJoseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Initialize stpg_endio() 'err' to SCSI_DH_OK and only change it to
SCSI_DH_IO accordingly.  This allows the switching of target group state
to be properly reported when no error has occurred.
Signed-off-by: NJoseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: NIlgu Hong <ilgu.hong@promise.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The use of blk_execute_rq_nowait() implies __blk_put_request() is needed
in stpg_endio() rather than blk_put_request() -- blk_finish_request() is
called with queue lock already held.
Signed-off-by: NJoseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: NIlgu Hong <ilgu.hong@promise.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

submit_stpg() will always return failure so alua_activate() will report
failure via dm-multipath callback function.  Even though the stpg fired
successfuly dm-multipath does not know and always fails to change the
valid path.

By returning SCSI_DH_OK we're now skipping alua_activate()'s call to
activate_complete 'fn'.  But this is fine because stpg_endio() will call
it via h->callback_fn().
Signed-off-by: NJoseph Gruher <joseph.r.gruher@intel.com>
Signed-off-by: NIlgu Hong <ilgu.hong@promise.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Upgrade driver version from 7.100.00.00 to 8.100.00.00
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Basic Code Cleanup:
(1) _base_get_cb_idx and mpt2sas_base_free_smid were reorganized in
similar fashion so the order of obtaining the cbx and smid are
scsiio,
hi_priority, and internal.
(2) The hi_priority and internal request queue struct was made
smaller
by removing the scmd and chain_tracker, thus saving memory
allocation.
(3) For scsiio request, a new structure was created having the same
elements from the former request tracker struct.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add support for Customer specific branding messages when device driver loads,
based on specific customer subsystem vendor and device Ids
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Revision P MPI Header Update:
a) Added enable/disable SATA NCQ operations to SAS IO Unit Control
Request.
b) Modified Host Based Discovery Action Request message format.
c) Removed Device Path bit from IO Unit Page 1 Flags field.
d) Added description of ChainOffset field for Diagnostic Data Upload
Tool.Chaining is not allowed.

Removed mpi2_history.txt file
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

You always needed them when you were a module, but the builtin versions
of the macros used to be more lenient.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

commit 3f0d3d01 adds a check for
PNP device id to the common tpm_tis_init() function, which in some
cases (force=1) will be called without the device being a member of
a pnp_dev. Oopsing and panics ensue.

Move the test up to before the call to tpm_tis_init(), since it
just modifies a global variable anyway.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

If duration variable value is 0 at this point, it's because
chip->vendor.duration wasn't filled by tpm_get_timeouts() yet.
This patch sets then the lowest timeout just to give enough
time for tpm_get_timeouts() to further succeed.

This fix avoids long boot times in case another entity attempts
to send commands to the TPM when the TPM isn't accessible.
Signed-off-by: NRajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

Fix new rapidio kernel-doc warnings:

  Warning(drivers/rapidio/rio-scan.c:953): No description found for parameter 'prev'
  Warning(drivers/rapidio/rio-scan.c:953): No description found for parameter 'prev_port'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix error test in fan_{read,write}_reg()
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It turns out that some device drivers map pages from the ACPI NVS region
during resume using ioremap(), which conflicts with ioremap_cache() used
for mapping those pages by the NVS save/restore code in nvs.c.

Make the NVS pages mapped by the code in nvs.c be unmapped before device
drivers' resume routines run.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>