Update GPIO mapping for T3C.
Update xgmac for T3C support.
Fix typo in mtu table.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	Fixes a race condition in module unload.  Without this change,
workqueue events may fire while bonding data structures are partially
freed but before bond_close() is invoked by unregister_netdevice().

	Update version to 3.2.3.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 	Add new hash for balance-xor and 802.3ad modes.  Originally
 submitted by "Glenn Griffin" <ggriffin.kernel@gmail.com>; modified by
 Jay Vosburgh to move setting of hash policy out of line, tweak the
 documentation update and add version update to 3.2.2.

	Glenn's original comment follows:

Included is a patch for a new xmit_hash_policy for the bonding driver
that selects slaves based on MAC and IP information.  This is a middle
ground between what currently exists in the layer2 only policy and the
layer3+4 policy.  This policy strives to be fully 802.3ad compliant by
transmitting every packet of any particular flow over the same link.
As documented the layer3+4 policy is not fully compliant for extreme
cases such as ip fragmentation, so this policy is a nice compromise
for environments that require full compliance but desire more than the
layer2 only policy.
Signed-off-by: N"Glenn Griffin" <ggriffin.kernel@gmail.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: David Sterba <dsterba@suse.cz>

Use macros for comparing jiffies. Jiffies' wrap caused missed events and hangs.
Module reinsert was needed to make bonding work again.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

For consistency with the behaviour of the arp_ip_target option,
let /sys/class/net/bond0/bonding/xmit_hash_policy accept and report
current policy even if the bonding mode in effect does not use it.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

Adhere to coding style: break line after the if condition
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

Code for rendering multivalue sysfs files occurs three times
in this module.  Rename 'buffer' to 'buf' in the first, for
the sake of consistency.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

The previous code returned '\n' (that is, a single empty line)
from most files, with one exception (xmit_hash_policy), where
it returned 'NA\n'.  This patch consolidates each file to return
nothing at all if not applicable, not even a '\n'.

I find this behaviour more usual, more useful, more efficient
and shorter to code from both sides.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

From: Wagner Ferenc <wferi@niif.hu>

Also remove trailing spaces from multivalued files.

This fixes output like for example:

$ od -c /sys/class/net/bond0/bonding/slaves
0000000   e   t   h   -   l   e   f   t       e   t   h   -   r   i   g
0000020   h   t      \n  \0
0000025

It mostly entails deleting '+1'-s after sprintf() calls: the return value
of sprintf is the number of characters printed, without the closing NUL,
ie. exactly what the sysfs interface requires.  The three multivalue
cases are different, because they also have to swallow back a trailing
space.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The timer broadcast code might access HPET, which should not be
accessed after the busmaster disable.

In acpi_idle_enter_simple() this change also prevents, that we modify
the busmaster state without going actually idle. This might leave the
ACPI bm state in a stale state, when we leave the function early in
the need_resched() check.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>

Convert part of the led trigger core from rw spinlocks to rw
semaphores. We're calling functions which can sleep from invalid
contexts otherwise. Fixes bug #9264.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

The LED in the current driver will not be controlled correctly. During
a link change the carrier of the link is not available and the LED
will never turn on.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

radeonfb was HPMC-ing my C8000 by trying to map its expansion rom from
IO_VIEW, instead of PA_VIEW. Fix seems to be to ensure that its disabled
ROM is properly inserted into the resource tree.

FIXME: this will result in a whinging printk for cards which share expansion
ROMS, such as a quad tulip. Thankfully, it isn't harmful.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

The AMD CS5535/CS5536 GPIO has two alternate output modes: AUX-1 and AUX-2.
When either AUX is enabled, the cs5535_gpio driver cannot control the
output.

Some BIOS code for the Geode processor enables AUX-1 for GPIO-1, which
configures it as the PC BEEP output.

This patch will disable AUX-1 and AUX-2 when the user enables output.
Signed-of-by: NBen Gardner <gardner.ben@gmail.com>
Cc: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

 - reconfigure SPI baud from speed_hz of each spi transfer
 - according to spi_transfer.bits_per_word to reprogram register and setup
   correct SPI operation handlers
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time

 - move this static things to the blackfin board file
 - add pin_req array to struct bfin5xx_spi_master
 - tested on BF537/BF548 with SPI flash
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move cs_chg_udelay handling (specific to this driver) to cs_deactive(), fixing
a bug when some SPI LCD driver needs delay after cs_deactive.

Fix bug reported by Cameron Barfield <cbarfield@cyberdata.net>
https://blackfin.uclinux.org/gf/project/uclinux-dist/forum/?action=ForumBrowse&forum_id=39&_forum_action=ForumMessageBrowse&thread_id=23630&feedback=Message%20replied.

Cc: Cameron Barfield <cbarfield@cyberdata.net>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move global SPI regs_base and dma_ch to struct driver_data.  Test on BF54x SPI
Flash with 2 spi_master devices enabled.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move spin/waits to more correct locations in bfin SPI driver.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix SPI driver to work with SPI flash ST M25P16 on bf548

Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer.  But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.

This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move pin muxing to setup and cleanup methods.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing.  Plus other minor
updates.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely
Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Respect per-transfer cs_change field (protocol tweaking support) by
adding and using cs_active/cs_deactive functions.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cleanup and error handling

 - add error handling in SPI bus driver with selecting clients
 - use proper defines to access Blackfin MMRs
 - remove useless SSYNCs
 - cleaner use of portmux calls
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use new Blackfin portmux interface, add error handling.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Initial BF54x SPI support

 - support BF54x SPI0
 - clean up some code (whitespace etc)
 - will support multiports in the future
 - start using portmux calls
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification.  (Most didn't.)
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simplify spi_sync calling convention, eliminating the need to check both
the return value AND the message->status.  In consequence, this corrects
misbehaviours of spi_read and spi_write (which only checked the former) and
their callers.
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add comment to at25 driver that it's for EEPROM chips, not FLASH
chips ... the AT25 series has both types of chip, and sometimes
they're even pin-compatible.  The command sets are different, as
is the treatment of erasure.  (FLASH needs explicit erasure, but
with EEPROM it's implicit.)  Note that all vendors seem to have
this same confusion in their *25* series SPI memory parts.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make spi_write_then_read() use a mutex not a binary semaphore.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We must make sure that the RTC_DEV_BUSY flag has proper lock semantics,
i.e.  that the RTC_DEV_BUSY stores clearing the flag don't get reordered
before the preceeding stores and loads and vice versa.

Spotted by Nick Piggin.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a field to the lro_mgr struct so that drivers can specify how much
padding is required to align layer 3 headers when a packet is copied
into a freshly allocated skb by inet_lro.c:lro_gen_skb().  Without
padding, skbs generated by LRO will cause alignment warnings on
architectures which require strict alignment (seen on sparc64).

Myri10GE is updated to use this field.
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lately I've got this nice badness on mdio bus removal:

Device 'e0103120:06' does not have a release() function, it is broken and must be fixed.
------------[ cut here ]------------
Badness at drivers/base/core.c:107
NIP: c015c1a8 LR: c015c1a8 CTR: c0157488
REGS: c34bdcf0 TRAP: 0700   Not tainted  (2.6.23-rc5-g9ebadfbb-dirty)
MSR: 00029032 <EE,ME,IR,DR>  CR: 24088422  XER: 00000000
...
[c34bdda0] [c015c1a8] device_release+0x78/0x80 (unreliable)
[c34bddb0] [c01354cc] kobject_cleanup+0x80/0xbc
[c34bddd0] [c01365f0] kref_put+0x54/0x6c
[c34bdde0] [c013543c] kobject_put+0x24/0x34
[c34bddf0] [c015c384] put_device+0x1c/0x2c
[c34bde00] [c0180e84] mdiobus_unregister+0x2c/0x58
...

Though actually there is nothing broken, it just device
subsystem core expects another "pattern" of resource managment.

This patch implement phy device's release function, thus
we're getting rid of this badness.

Also small hidden bug fixed, hope none other introduced. ;-)
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Eliminate an uninitialized variable warning.  The code is correct, but
a pointer to the automatic variable 'addr' is passed to dma_alloc_coherent.
Since addr has never been initialized, and the compiler doesn't know
what dma_alloc_coherent will do with it, it complains.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>