Adopt the "info: why not propagate 'ret' from parse_trans_rule()..."
suggestion made by the smatch semantic checker on:
drivers/net/ethernet/mellanox/mlx4/mcg.c:867 mlx4_flow_attach()
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using a positive value for error: MLX4_NET_TRANS_RULE_NUM instead
of -EPROTONOSUPPORT, to remove compilation warning.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This Patches solves an issue that could raise when modifying the
device's MAC. It occurs due to a simultaneous access to priv->mac_hash
from two contexts. The buggy scenario described below:
Context 1: copy the new mac address to the dev->dev_addr field.
Context 2: mlx4_en_do_uc_filter removes prev_mac entry from the mac_hash
           db since it is not in dev->uc and not equal to dev->dev_addr.
Context 1: mlx4_en_do_set_mac() calls mlx4_en_replace_mac() to replace
           prev_mac with dev_addr but it fails to update the mac_hash db
           since it no longer contains prev_mac, therefore it returns
           with an error.

The fix is to prevent mlx4_en_do_uc_filter from being executed by both
of the context 1 calls described above, This is done by putting them
both under the mdev->state_lock lock, it will solve this issue since
mlx4_en_do_uc_filter is already protected by the mdev->state_lock.
Reviewed-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the "warn: suspicious bitop condition" made by the smatch semantic
checker on:
drivers/net/ethernet/mellanox/mlx4/main.c:509 mlx4_slave_cap()
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the "error: we previously assumed 'out_param' could be null" found
by smatch semantic checker on:
drivers/net/ethernet/mellanox/mlx4/cmd.c:506 mlx4_cmd_poll()
drivers/net/ethernet/mellanox/mlx4/cmd.c:578 mlx4_cmd_wait()
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fix an issue that happen when changing the MAC address when
the port is down, described as follows:
1. Set the port down.
2. Change the MAC address - mlx4_en_set_mac() will change dev->dev_addr.
3. Set the port up - will result in mlx4_en_do_uc_filter that will
   remove the prev_mac entry from the mac_hash db.
4. Changing the MAC address again will eventually trigger the call to
   mlx4_en_replace_mac() in order to replace prev_mac with dev_addr but
   the prev_mac entry is already not exist in the mac_hash db therefore
   the operation fails.

The fix is to set the prev_mac with the new MAC address so in step 3
above, after setting the port up mlx4_en_get_qp() is updating the
mac_hash with the entry of dev_addr which is equal to prev_mac.
Therefore in step 4, when calling mlx4_en_replace_mac, the entry related
to prev_mac exist in mac_hash and the replace operation succeed.
Reviewed-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using ethtool set_channels, mlx4_en_setup_tc is always called, even
when it was not configured. Fixed code to call mlx4_en_setup_tc() only
if needed.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During heavy traffic, napi is constatntly polling the complition queue
and no interrupt is fired. Because of that, changes to irq affinity are
ignored until traffic is stopped and resumed.

By registering to the irq notifier mechanism, and forcing interrupt when
affinity is changed, irq affinity changes will be immediatly enforced.
Signed-off-by: NYuval Atias <yuvala@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the physical MTU changes we should ensure that all existing MACVLAN
dev MTU do not exceed the new lowerdev MTU. This patch adds that
propagation.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Documentation/networking/dccp.txt points that request_retries
should be greater than 0. So make the extra1 to be &one instead
of &zero.
Signed-off-by: NWang Weidong <wangweidong1@huawei.com>
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fengguang reported the following sparse warning:

>> net/ipv6/proc.c:198:41: sparse: incorrect type in argument 1 (different address spaces)
   net/ipv6/proc.c:198:41:    expected void [noderef] <asn:3>*mib
   net/ipv6/proc.c:198:41:    got void [noderef] <asn:3>**pcpumib

Fixes: commit 698365fa (net: clean up snmp stats code)
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip_local_port_range is already per netns, so should ip_local_reserved_ports
be. And since it is none by default we don't actually need it when we don't
enable CONFIG_SYSCTL.

By the way, rename inet_is_reserved_local_port() to inet_is_local_reserved_port()

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This helps increasing build testing coverage.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: bug fixes and improvements

Intensive and extensive testing has revealed some rather infrequent
problems related to flow control, buffer handling and link
establishment. Commits ##1 to 4 deal with these problems.

The remaining four commits are just code improvments, aiming at
making the code more comprehensible and maintainable. There are
no functional enhancements in this series.

v2: Fixed a typo in commit log #2. Otherwise no changes from v1.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to reduce complexity and save a call level during message
reception at port/socket level, we remove the function tipc_port_rcv()
and merge its functionality into tipc_sk_rcv().
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function tipc_disc_rcv(), which is handling received neighbor
discovery messages, is perceived as messy, and it is hard to verify
its correctness by code inspection. The fact that the task it is set
to resolve is fairly complex does not make the situation better.

In this commit we try to take a more systematic approach to the
problem. We define a decision machine which takes three state flags
 as input, and produces three action flags as output. We then walk
through all permutations of the state flags, and for each of them we
describe verbally what is going on, plus that we set zero or more of
the action flags. The action flags indicate what should be done once
the decision machine has finished its job, while the last part of the
function deals with performing those actions.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC currently handles two media specific addresses: Ethernet MAC
addresses and InfiniBand addresses. Those are kept in three different
formats:

1) A "raw" format as obtained from the device. This format is known
   only by the media specific adapter code in eth_media.c and
   ib_media.c.
2) A "generic" internal format, in the form of struct tipc_media_addr,
   which can be referenced and passed around by the generic media-
   unaware code.
3) A serialized version of the latter, to be conveyed in neighbor
   discovery messages.

Conversion between the three formats can only be done by the media
specific code, so we have function pointers for this purpose in
struct tipc_media. Here, the media adapters can install their own
conversion functions at startup.

We now introduce a new such function, 'raw2addr()', whose purpose
is to convert from format 1 to format 2 above. We also try to as far
as possible uniform commenting, variable names and usage of these
functions, with the purpose of making them more comprehensible.

We can now also remove the function tipc_l2_media_addr_set(), whose
job is done better by the new function.

Finally, we expand the field for serialized addresses (format 3)
in discovery messages from 20 to 32 bytes. This is permitted
according to the spec, and reduces the risk of problems when we
add new media in the future.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function tipc_link_frag_rcv() is in reality a re-entrant generic
message reassemby function that has nothing in particular to do with
the link, where it is defined now. This becomes obvious when we see
the need to call the function from other places in the code.

In this commit rename it to tipc_buf_append() and move it to the file
msg.c. We also simplify its signature by moving the tail pointer to
the control block of the head buffer, hence making the head buffer
self-contained.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The message reassembly function does not update the 'len' and 'data_len'
fields of the head skbuff correctly when fragments are chained to it.
This may sometimes lead to obsure errors, such as fragment reordering
when we receive fragments which are cloned buffers.

This commit fixes this, by ensuring that the two fields are updated
correctly.
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current code, all incoming LINK_PROTOCOL messages, irrespective
of type, nudge the "last message received" checkpoint, informing the
link state machine that a message was received from the peer since last
supervision timeout event. This inhibits the link from starting probing
the peer unnecessarily.

However, not only STATE messages are recorded as legitimate incoming
traffic this way, but even RESET and ACTIVATE messages, which in
reality are there to inform the link that the peer endpoint has been
reset. At the same time, some RESET messages may be dropped instead
of causing a link reset. This happens when the link endpoint thinks
it is fully up and working, and the session number of the RESET is
lower than or equal to the current link session. In such cases the
RESET is perceived as a delayed remnant from an earlier session, or
the current one, and dropped.

Now, if a TIPC module is removed and then immediately reinserted, e.g.
when using a script, RESET messages may arrive at the peer link endpoint
before this one has had time to discover the failure. The RESET may be
dropped because of the session number, but only after it has been
recorded as a legitimate traffic event. Hence, the receiving link will
not start probing, and not discover that the peer endpoint is down, at
the same time ignoring the periodic RESET messages coming from that
endpoint. We have ended up in a stale state where a failed link cannot
be re-established.

In this commit, we remedy this by nudging the checkpoint only for
received STATE messages, not for RESET or ACTIVATE messages.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function net/core/sock.c::__release_sock() runs a tight loop
to move buffers from the socket backlog queue to the receive queue.

As a security measure, sk_backlog.len of the receiving socket
is not set to zero until after the loop is finished, i.e., until
the whole backlog queue has been transferred to the receive queue.
During this transfer, the data that has already been moved is counted
both in the backlog queue and the receive queue, hence giving an
incorrect picture of the available queue space for new arriving buffers.

This leads to unnecessary rejection of buffers by sk_add_backlog(),
which in TIPC leads to unnecessarily broken connections.

In this commit, we compensate for this double accounting by adding
a counter that keeps track of it. The function socket.c::backlog_rcv()
receives buffers one by one from __release_sock(), and adds them to the
socket receive queue. If the transfer is successful, it increases a new
atomic counter 'tipc_sock::dupl_rcvcnt' with 'truesize' of the
transferred buffer. If a new buffer arrives during this transfer and
finds the socket busy (owned), we attempt to add it to the backlog.
However, when sk_add_backlog() is called, we adjust the 'limit'
parameter with the value of the new counter, so that the risk of
inadvertent rejection is eliminated.

It should be noted that this change does not invalidate the original
purpose of zeroing 'sk_backlog.len' after the full transfer. We set an
upper limit for dupl_rcvcnt, so that if a 'wild' sender (i.e., one that
doesn't respect the send window) keeps pumping in buffers to
sk_add_backlog(), he will eventually reach an upper limit,
(2 x TIPC_CONN_OVERLOAD_LIMIT). After that, no messages can be added
to the backlog, and the connection will be broken. Ordinary, well-
behaved senders will never reach this buffer limit at all.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Memory overhead when allocating big buffers for data transfer may
be quite significant. E.g., truesize of a 64 KB buffer turns out
to be 132 KB, 2 x the requested size.

This invalidates the "worst case" calculation we have been
using to determine the default socket receive buffer limit,
which is based on the assumption that 1024x64KB = 67MB buffers
may be queued up on a socket.

Since TIPC connections cannot survive hitting the buffer limit,
we have to compensate for this overhead.

We do that in this commit by dividing the fix connection flow
control window from 1024 (2*512) messages to 512 (2*256). Since
older version nodes send out acks at 512 message intervals,
compatibility with such nodes is guaranteed, although performance
may be non-optimal in such cases.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The struct ad_slave_info is very huge, and only be used for 802.3ad mode,
so alloc the structure dynamically could save 356 Bits for every slave in
non 802.3ad mode.

Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Acked-by: NVeaceslav Falico <vfalico@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I was converting the driver to the managed device API, only devm_kzalloc()
was available for memory allocation, so I had to use it, despite zeroing out the
PHY IRQ array right before initializing all  its entries to PHY_POLL was quite
stupid.   Now that devm_kmalloc_array() has become available, we can avoid the
needless zeroing out...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Chan says:

====================
tg3: TSO related enhancements to prevent memory allocation failure

Michael Chan (3):
  tg3: Don't modify ip header fields when doing GSO
  tg3: Prevent page allocation failure during TSO workaround
  tg3: Update copyright and version to 3.137
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If any TSO fragment hits hardware bug conditions (e.g. 4G boundary), the
driver will workaround by calling skb_copy() to copy to a linear SKB.  Users
have reported page allocation failures as the TSO packet can be up to 64K.
Copying such a large packet is also very inefficient.  We fix this by using
existing tg3_tso_bug() to transmit the packet using GSO.
Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3 uses GSO as workaround if the hardware cannot perform TSO on certain
packets.  We should not modify the ip header fields if we do GSO on the
packet.  It happens to work by accident because GSO recalculates the IP
checksum and IP total length.

Also fix the tg3_start_xmit comment to reflect that this is the only
xmit function for all devices.
Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lorenzo Colitti says:

====================
Make mark-based routing work better with multiple separate networks.

Mark-based routing (ip rule fwmark 17 lookup 100) combined with
either iptables marking (iptables -j MARK --set-mark 17) or
application-based marking (the SO_MARK setsockopt) are a good
way to deal with connecting simultaneously to multiple networks.

Each network can be given a routing table, and ip rules can
be configured to make different fwmarks select different
networks. Applications can select networks them by setting
appropriate socket marks, and iptables rules can be used to
handle non-aware applications, enforce policy, etc.

This patch series improves functionality when mark-based routing
is used in this way. Current behaviour has the following
limitations:

1. Kernel-originated replies that are not associated with a
   socket always use a mark of zero. This means that, for
   example, when the kernel sends a ping reply or a TCP reset,
   it does not send it on the network from which it received the
   original packet.
2. Path MTU discovery, which is triggered by incoming packets,
   does not always work correctly, because the routing lookups it
   uses to clone routes do not take the fwmark into account and
   thus can happen in the wrong routing table.
3. Application-based marking works well for outbound connections,
   but does not work well for incoming connections. Marking a
   listening socket causes that socket to only accept
   connections from a given network, and sockets that are
   returned by accept() are not marked (and are thus not routed
   correctly).

sysctl. This causes route lookups for kernel-generated replies
and PMTUD to use the fwmark of the packet that caused them.

which causes TCP sockets returned by accept() to be marked with
the same mark that sent the intial SYN packet.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using mark-based routing, sockets returned from accept()
may need to be marked differently depending on the incoming
connection request.

This is the case, for example, if different socket marks identify
different networks: a listening socket may want to accept
connections from all networks, but each connection should be
marked with the network that the request came in on, so that
subsequent packets are sent on the correct network.

This patch adds a sysctl to mark TCP sockets based on the fwmark
of the incoming SYN packet. If enabled, and an unmarked socket
receives a SYN, then the SYN packet's fwmark is written to the
connection's inet_request_sock, and later written back to the
accepted socket when the connection is established.  If the
socket already has a nonzero mark, then the behaviour is the same
as it is today, i.e., the listening socket's fwmark is used.

Black-box tested using user-mode linux:

- IPv4/IPv6 SYN+ACK, FIN, etc. packets are routed based on the
  mark of the incoming SYN packet.
- The socket returned by accept() is marked with the mark of the
  incoming SYN packet.
- Tested with syncookies=1 and syncookies=2.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, routing lookups used for Path PMTU Discovery in
absence of a socket or on unmarked sockets use a mark of 0.
This causes PMTUD not to work when using routing based on
netfilter fwmark mangling and fwmark ip rules, such as:

  iptables -j MARK --set-mark 17
  ip rule add fwmark 17 lookup 100

This patch causes these route lookups to use the fwmark from the
received ICMP error when the fwmark_reflect sysctl is enabled.
This allows the administrator to make PMTUD work by configuring
appropriate fwmark rules to mark the inbound ICMP packets.

Black-box tested using user-mode linux by pointing different
fwmarks at routing tables egressing on different interfaces, and
using iptables mangling to mark packets inbound on each interface
with the interface's fwmark. ICMPv4 and ICMPv6 PMTU discovery
work as expected when mark reflection is enabled and fail when
it is disabled.
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kernel-originated IP packets that have no user socket associated
with them (e.g., ICMP errors and echo replies, TCP RSTs, etc.)
are emitted with a mark of zero. Add a sysctl to make them have
the same mark as the packet they are replying to.

This allows an administrator that wishes to do so to use
mark-based routing, firewalling, etc. for these replies by
marking the original packets inbound.

Tested using user-mode linux:
 - ICMP/ICMPv6 echo replies and errors.
 - TCP RST packets (IPv4 and IPv6).
Signed-off-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Beniamino Galvani says:

====================
arc_emac: promiscuous/multicast mode and netpoll support

These patches add support for promiscuous mode, multicast filtering
and netpoll to the ARC EMAC driver.

They were both tested on a Radxa Rock board which uses a ARC EMAC IP
core integrated in the Rockchip RK3188 SoC.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the set_rx_mode function to enable/disable
promiscuous or all-multicast modes and to update the multicast
filtering list of the device.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tcp: IPv6 support for fastopen server

This patch series add IPv6 support for fastopen server. To minimize
code duplication in IPv4 and IPv6, the current v4 only code is
refactored and common code is moved into net/ipv4/tcp_fastopen.c.

Also the current code uses a different function from
tcp_v4_send_synack() to send the first SYN-ACK in fastopen.
The new code eliminates this separate function by refactoring the
child-socket and syn-ack creation code.  After these refactoring
in the first four patches, we can easily add the fastopen code in
IPv6 by changing corresponding IPv6 functions.

Note Fast Open client already supports IPv6. This patch is for
the server-side (passive open) IPv6 support only.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After all the preparatory works, supporting IPv6 in Fast Open is now easy.
We pretty much just mirror v4 code. The only difference is how we
generate the Fast Open cookie for IPv6 sockets. Since Fast Open cookie
is 128 bits and we use AES 128, we use CBC-MAC to encrypt both the
source and destination IPv6 addresses since the cookie is a MAC tag.
Signed-off-by: NDaniel Lee <longinus00@gmail.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NJerry Chu <hkchu@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a fast open socket is already accepted by the user, it should
be treated like a connected socket to record the ICMP error in
sk_softerr, so the user can fetch it. Do that in both tcp_v4_err
and tcp_v6_err.

Also refactor the sequence window check to improve readability
(e.g., there were two local variables named 'req').
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDaniel Lee <longinus00@gmail.com>
Signed-off-by: NJerry Chu <hkchu@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To avoid large code duplication in IPv6, we need to first simplify
the complicate SYN-ACK sending code in tcp_v4_conn_request().

To use tcp_v4(6)_send_synack() to send all SYN-ACKs, we need to
initialize the mini socket's receive window before trying to
create the child socket and/or building the SYN-ACK packet. So we move
that initialization from tcp_make_synack() to tcp_v4_conn_request()
as a new function tcp_openreq_init_req_rwin().

After this refactoring the SYN-ACK sending code is simpler and easier
to implement Fast Open for IPv6.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDaniel Lee <longinus00@gmail.com>
Signed-off-by: NJerry Chu <hkchu@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Consolidate various cookie checking and generation code to simplify
the fast open processing. The main goal is to reduce code duplication
in tcp_v4_conn_request() for IPv6 support.

Removes two experimental sysctl flags TFO_SERVER_ALWAYS and
TFO_SERVER_COOKIE_NOT_CHKD used primarily for developmental debugging
purposes.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDaniel Lee <longinus00@gmail.com>
Signed-off-by: NJerry Chu <hkchu@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>