There's plenty of drm/i915 related hardware and software documentation,
and firmware downloads for the latest platforms.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some registers are, naturally, lost in gpu reset/suspend cycle.
And some registers, for example in display domain, are not subject
to gpu reset so they retain their contents.

As hang recovery triggers a reset, recoverable gpu hang can currently
flush out essential workarounds and cause havoc later on.

When register GEN8_GARBNTL is missing the WaEnableGapsTsvCreditFix:skl,
it can cause random system hangs [1]. This workaround was added in:
commit 245d9667 ("drm/i915:skl: Add WaEnableGapsTsvCreditFix")
But another set of system hangs were observed and the failure pattern
indicated that there was random gpu hang preceding the system hang [2].
This lead to the realization that we lose this workaround and BDW_SCRATCH1
on reset.

Add these workarounds setup in display init to skl/bxt ring init
where LRI workarounds are also setup. This way their setup is not
dependent on display side init.

References: [1] https://bugs.freedesktop.org/show_bug.cgi?id=90854
References: [2] https://bugs.freedesktop.org/show_bug.cgi?id=92315Reported-by: NTomi Sarvela <tomix.p.sarvela@intel.com>
Cc: Tomi Sarvela <tomix.p.sarvela@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NTomi Sarvela <tomix.p.sarvela@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since the remove of the pin-ioctl, we only care about not changing the
cache level on buffers pinned to the hardware as indicated by
obj->pin_display. By knowing that only objects pinned to the hardware
will have an elevated vma->pin_count, so we can coallesce many of the
linear walks over the obj->vma_list.

v2: Try and retrospectively add comments explaining the steps in
rebinding the active VMA.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a squash of the following commits:

Revert "drm/i915: Drop intel_update_sprite_watermarks"
This reverts commit 47c99438.

Revert "drm/i915/ivb: Move WaCxSRDisabledForSpriteScaling w/a to atomic check"
This reverts commit 7809e5ae.

Revert "drm/i915/skl: Eliminate usage of pipe_wm_parameters from SKL-style WM (v3)"
This reverts commit 3a05f5e2.

With these reverts, SKL finally stops failing every single FBC test
with FIFO underrun error messages. After some brief testing, it also
seems that this commit prevents the machine from completely freezing
when we run igt/kms_fbc_crc (see fd.o #92355).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92355
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Keep single 'lvds_reg' and 'lvds' variable around in
intel_lvds_init(), and read it just once at the start.

Also intel_lvds_get_config() doesn't need to figure out which reg to use
since it can just consult lvds_encoder->reg.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Drop some useless 'reg' variables when we only use them once.

v2: A few more, including a few variable moves
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Parametrize the SWF registers. This also fixes the register offsets,
which were mostly garbage in the old defines.

Also save/restore only as many SWF registers that each platform has.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The PIPE_FRMCOUNT_GM45 and PIPE_FLIPCOUNT_GM45 names have bothered me
for a long time. The work equally well for ELK and onwards, so let's
s/GM45/G4X/.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A few register mask defines were missing the '0x' from hex numbers. Or
at least I assume those were meant to be hex numbers. Put the '0x' in
place.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Always put parens around macro argument evaluations.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Keep using the same registers (PCH_*) instead of accidentally
    starting to use the other ones (BXT_*)2) (Jesse)
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should serialise access to the intel_crtc->unpin_work through the
dev->event_lock spinlock. It should not be possible for it to disappear
without severe error as the mmio_flip worker has not tagged the
unpin_work pending flip-completion. Similarly if the error exists, just
taking the unpin_work whilst holding the spinlock and then using it
unserialised just masks the race. (It is supposed to be valid as the
unpin_work exists until the flip completion interrupt which should not
fire until we flush the mmio writes to update the display base which is
the last time we access the unpin_work from the kthread.)

References: https://bugs.freedesktop.org/show_bug.cgi?id=92335Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

i915 expects the OpRegion to be cached (i.e. not __iomem), so explicitly
map it with memremap rather than the implied cache setting of
acpi_os_ioremap().

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Commit 599bbb9d ("drm/i915: i915 cannot provide switcher services.")
removed all remaining vga_switcheroo symbols from intel_acpi.c but left
the include. Drop it.
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's been reported that the atomic watermark series triggers some
regressions on SKL, which we haven't been able to track down yet.  Let's
temporarily revert these patches while we track down the root cause.

This commit squashes the reverts of:
  76305b1a drm/i915: Calculate watermark configuration during atomic check (v2)
  a4611e44 drm/i915: Don't set plane visible during HW readout if CRTC is off
  a28170f3 drm/i915: Calculate ILK-style watermarks during atomic check (v3)
  de4a9f83 drm/i915: Calculate pipe watermarks into CRTC state (v3)
  de165e0b drm/i915: Refactor ilk_update_wm (v3)

Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-October/077190.html
Cc: "Zanoni, Paulo R" <paulo.r.zanoni@intel.com>
Cc: "Vetter, Daniel" <daniel.vetter@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When submitting semaphores in execlist mode the hang checker crashes in this
function because it is only runnable in ring submission mode. The reason this
is of particular interest to the TDR patch series is because we use semaphores
as a mean to induce hangs during testing (which is the recommended way to
induce hangs for gen8+). It's not clear how this is supposed to work in
execlist mode since:

1. This function requires a ring buffer.

2. Retrieving a ring buffer in execlist mode requires us to retrieve the
corresponding context, which we get from a request.

3. Retieving a request from the hang checker is not straight-forward since that
requires us to grab the struct_mutex in order to synchronize against the
request retirement thread.

4. Grabbing the struct_mutex from the hang checker is nothing that we will do
since that puts us at risk of deadlock since a hung thread might be holding the
struct_mutex already.

Therefore it's not obvious how we're supposed to deal with this. For now, we're
doing an early exit from this function, which avoids any kernel panic situation
when running our own internal TDR ULT.

* v2: (Chris Wilson)
Turned the execlist mode check into a ringbuffer NULL check to make it more
submission mode agnostic and less of a layering violation.
Signed-off-by: NTomas Elf <tomas.elf@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

commit e9f24d5f
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date:   Mon Oct 5 13:26:36 2015 +0100

    drm/i915: Clean up associated VMAs on context destruction

Introduced a wrong assumption that all contexts have a ppgtt
instance. This is not true when full PPGTT is not active so
remove the WARN_ON_ONCE from the context cleanup code.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There isn't an explicit stolen memory base register on gen2.
Some old comment in the i915 code suggests we should get it via
max_low_pfn_mapped, but that's clearly a bad idea on my MGM.

The e820 map in said machine looks like this:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000ce000-0x00000000000cffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000dc000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001f6effff] usable
[    0.000000] BIOS-e820: [mem 0x000000001f6f0000-0x000000001f6f7fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000001f6f8000-0x000000001f6fffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000001f700000-0x000000001fffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffbfffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved

That makes max_low_pfn_mapped = 1f6f0000, so assuming our stolen memory
would start there would place it on top of some ACPI memory regions.
So not a good idea as already stated.

The 9MB region after the ACPI regions at 0x1f700000 however looks
promising given that the macine reports the stolen memory size to be
8MB. Looking at the PGTBL_CTL register, the GTT entries are at offset
0x1fee00000, and given that the GTT entries occupy 128KB, it looks like
the stolen memory could start at 0x1f700000 and the GTT entries would
occupy the last 128KB of the stolen memory.

After some more digging through chipset documentation, I've determined
the BIOS first allocates space for something called TSEG (something to
do with SMM) from the top of memory, and then it allocates the graphics
stolen memory below that. Accordind to the chipset documentation TSEG
has a fixed size of 1MB on 855. So that explains the top 1MB in the
e820 region. And it also confirms that the GTT entries are in fact at
the end of the the stolen memory region.

Derive the stolen memory base address on gen2 the same as the BIOS does
(TOM-TSEG_SIZE-stolen_size). There are a few differences between the
registers on various gen2 chipsets, so a few different codepaths are
required.

865G is again bit more special since it seems to support enough memory
to hit 4GB address space issues. This means the PCI allocations will
also affect the location of the stolen memory. Fortunately there
appears to be the TOUD register which may give us the correct answer
directly. But the chipset docs are a bit unclear, so I'm not 100%
sure that the graphics stolen memory is always the last thing the
BIOS steals. Someone would need to verify it on a real system.

I tested this on the my 830 and 855 machines, and so far everything
looks peachy.

v2: Rewrite to use the TOM-TSEG_SIZE-stolen_size and TOUD methods
v3: Fix TSEG size for 830
v4: Add missing 'else' (Chris)
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to my experiments (and later confirmation from the hardware
developers), the maximum sizes mentioned in the specification delimit
how far in the buffer the hardware tracking can go. And the hardware
calculates the size based on the plane address we provide - and the
provided plane address might not be the real x:0,y:0 point due to the
compute_page_offset() function.

On platforms that do the x/y offset adjustment trick it will be really
hard to reproduce a bug, but on the current SKL we can reproduce the
bug with igt/kms_frontbuffer_tracking/fbc-farfromfence. With this
patch, we'll go from "CRC assertion failure" to "FBC unexpectedly
disabled", which is still a failure on the test suite but is not a
perceived user bug - you will just not save as much power as you could
if FBC is disabled.

v2, rewrite patch after clarification from the Hadware guys:
  - Rename function so it's clear what the check is for.
  - Use the new intel_fbc_get_plane_source_sizes() function in order
    to get the proper sizes as seen by FBC.
v3:
  - Rebase after the s/sizes/size/ on the previous patch.
  - Adjust comment wording (Ville).
  - s/used_/effective_/ (Ville).

Testcase: igt/kms_frontbuffer_tracking/fbc-farfromfence (SKL)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We were considering the whole framebuffer height, but the spec says we
should only consider the active display height size. There were still
some unclear questions based on the spec, but the hardware guys
clarified them for us. According to them:

- CFB size = CFB stride * Number of lines FBC writes to CFB
- CFB stride = plane stride / compression limit
- Number of lines FBC writes to CFB = MIN(plane source height, maximum
  number of lines FBC writes to CFB)
- Plane source height =
  - pipe source height (PIPE_SRCSZ register) (before SKL)
  - plane size register height (PLANE_SIZE register) (SKL+)
- Maximum number of lines FBC writes to CFB =
  - plane source height (before HSW)
  - 2048 (HSW+)

For the plane source height, I could just have made our code do
I915_READ() in order to be more future proof, but since it's not cool
to do register reads I decided to just recalculate the values we use
when we actually write to those registers.

With this patch, depending on your machine configuration, a lot of the
kms_frontbuffer_tracking subtests that used to result in a SKIP due to
not enough stolen memory still start resulting in a PASS.

v2: Use the clipped src size instead of pipe_src_h (Ville).
v3: Use the appropriate information provided by the hardware guys.
v4: Bikesheds: s/sizes/size/, s/fb_cpp/cpp/ (Ville).
v5: - Don't use crtc->config->pipe_src_x for BDW- (Ville).
    - Fix the register name written in the comment.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The comment suggests the check was there for some non-fully-atomic
case, and I couldn't find a case where we wouldn't correctly
initialize plane_state, so remove the check.

Let's leave a WARN there just in case.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Technology has evolved and now we have eDP panels with 3200x1800
resolution. In the meantime, the BIOS guys didn't change the default
32mb for stolen memory. On top of that, we can't assume our users will
be able to increase the default stolen memory size to more than 32mb -
I'm not even sure all BIOSes allow that.

So just the fbcon buffer alone eats 22mb of my stolen memroy, and due
to the BDW/SKL restriction of not using the last 8mb of stolen memory,
all that's left for FBC is 2mb! Since fbcon is not the coolest feature
ever, I think it's better to save our precious stolen resource to FBC
and the other guys.

On the other hand, we really want to use as much stolen memory as
possible, since on some older systems the stolen memory may be a
considerable percentage of the total available memory.

This patch tries to achieve a little balance using a simple heuristic:
if the fbcon wants more than half of the available stolen memory,
don't use stolen memory in order to leave some for FBC and the other
features.

The long term plan should be to implement a way to set priorities for
stolen memory allocation and then evict low priority users when the
high priority ones need the memory. While we still don't have that,
let's try to make FBC usable with the simple solution.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This reverts commit 5d250b05.

It results on a deadlock on platforms where we need to (at least
partially) re-init hpd interrupts from power domain code, since
->hot_plug might again grab a power well reference (to do edid/dp_aux
transactions. At least chv is affected.
Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
References: http://mid.gmane.org/20151008133548.GX26517@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@intel.com>

This reverts commit 0b5e88dc.

It completely breaks booting on at least bsw (and maybe more).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88081Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Use goto to handle the error path to avoid duplicating the same code. In
the error path intel_dig_port is the last one to be released as it was
the first one to be allocated and ideally the error path should be the
reverse of the execution path.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is a typo in the function i915_handle_error()
kernel-doc and the word register is spelled wrongly.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add the dev parameter for the functions i915_enable_asle_pipestat() and
i915_reset_and_wakeup() to the kernel-doc to fix the following warnings:

.//drivers/gpu/drm/i915/i915_irq.c:586: warning: No description found for parameter 'dev'
.//drivers/gpu/drm/i915/i915_irq.c:2400: warning: No description found for parameter 'dev'
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_rcs_ctx_init() emits all workaround register writes on the list
to the ring, in addition to calling i915_gem_render_state_init().  The
workaround list is currently empty on Gen6-7 so this shouldn't cause
any functional changes.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not an error for the workaround list to be empty if no
workarounds are needed.  This will avoid spamming the logs
unnecessarily on Gen6 after the workaround list is hooked up on
pre-Gen8 hardware by the following commits.
Signed-off-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In

commit 8f0e2b9d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Dec 2 16:19:07 2014 +0100

    drm/i915: Move golden context init into ->init_context

I've shuffled around per-ctx init code a bit for legacy contexts but
accidentally dropped the render state init call on gen6/7. Resurrect
it.
Reported-by: NFrancisco Jerez <currojerez@riseup.net>
Cc: Francisco Jerez <currojerez@riseup.net>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Appease gcc and remove the unused variable.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Note that in Bspec you have to dig around in a section called
"Timestamp bases" and Bspec update request is filed.
Signed-off-by: NAnkitprasad Sharma <ankitprasad.r.sharma@intel.com>
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
[danvet: Add note about state of Bspec.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Passing cliprects into the kernel for it to re-execute the batch buffer
with different CMD_DRAWRECT died out long ago. As DRI1 support has been
removed from the kernel, we can now simply reject any execbuf trying to
use this "feature".

To keep Daniel happy with the prospect of being able to reuse these
fields in the next decade, continue to ensure that current userspace is
not passing garbage in through the dead fields.

v2: Fix the cliprects_ptr check
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Exclude active GPU pages from the purview of the background shrinker
(kswapd), as these cause uncontrollable GPU stalls. Given that the
shrinker is rerun until the freelists are satisfied, we should have
opportunity in subsequent passes to recover the pages once idle. If the
machine does run out of memory entirely, we have the forced idling in the
oom-notifier as a means of releasing all the pages we can before an oom
is prematurely executed.

Note that this relies upon an up-front retire_requests to keep the
inactive list in shape, which was added in a previous patch, mostly as
execlist ctx pinning band-aids.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Add note about retire_requests.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>