Implementing the advanced early retransmit (sysctl_tcp_early_retrans==2).
Delays the fast retransmit by an interval of RTT/4. We borrow the
RTO timer to implement the delay. If we receive another ACK or send
a new packet, the timer is cancelled and restored to original RTO
value offset by time elapsed.  When the delayed-ER timer fires,
we enter fast recovery and perform fast retransmit.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements RFC 5827 early retransmit (ER) for TCP.
It reduces DUPACK threshold (dupthresh) if outstanding packets are
less than 4 to recover losses by fast recovery instead of timeout.

While the algorithm is simple, small but frequent network reordering
makes this feature dangerous: the connection repeatedly enter
false recovery and degrade performance. Therefore we implement
a mitigation suggested in the appendix of the RFC that delays
entering fast recovery by a small interval, i.e., RTT/4. Currently
ER is conservative and is disabled for the rest of the connection
after the first reordering event. A large scale web server
experiment on the performance impact of ER is summarized in
section 6 of the paper "Proportional Rate Reduction for TCP”,
IMC 2011. http://conferences.sigcomm.org/imc/2011/docs/p155.pdf

Note that Linux has a similar feature called THIN_DUPACK. The
differences are THIN_DUPACK do not mitigate reorderings and is only
used after slow start. Currently ER is disabled if THIN_DUPACK is
enabled. I would be happy to merge THIN_DUPACK feature with ER if
people think it's a good idea.

ER is enabled by sysctl_tcp_early_retrans:
  0: Disables ER

  1: Reduce dupthresh to packets_out - 1 when outstanding packets < 4.

  2: (Default) reduce dupthresh like mode 1. In addition, delay
     entering fast recovery by RTT/4.

Note: mode 2 is implemented in the third part of this patch series.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ECN (Explicit Congestion Notification) marking capability to netem

tc qdisc add dev eth0 root netem drop 0.5 ecn

Instead of dropping packets, try to ECN mark them.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: NHagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

remove useless casts and rename variables for less confusion.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

L2TPv3 defines an IP encapsulation packet format where data is carried
directly over IP (no UDP). The kernel already has support for L2TP IP
encapsulation over IPv4 (l2tp_ip). This patch introduces support for
L2TP IP encapsulation over IPv6.

The implementation is derived from ipv6/raw and ipv4/l2tp_ip.
Signed-off-by: NChris Elston <celston@katalix.com>
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for unmanaged L2TPv3 tunnels over IPv6 using
the netlink API. We already support unmanaged L2TPv3 tunnels over
IPv4. A patch to iproute2 to make use of this feature will be
submitted separately.
Signed-off-by: NChris Elston <celston@katalix.com>
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Checkpatch warns about the use of __attribute__((packed)). So use the
recommended __packed syntax instead.
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRO can check if skb to be merged has its skb->head mapped to a page
fragment, instead of a kmalloc() area.

We 'upgrade' skb->head as a fragment in itself

This avoids the frag_list fallback, and permits to build true GRO skb
(one sk_buff and up to 16 fragments), using less memory.

This reduces number of cache misses when user makes its copy, since a
single sk_buff is fetched.

This is a followup of patch "net: allow skb->head to be a page fragment"
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb->head is currently allocated from kmalloc(). This is convenient but
has the drawback the data cannot be converted to a page fragment if
needed.

We have three spots were it hurts :

1) GRO aggregation

 When a linear skb must be appended to another skb, GRO uses the
frag_list fallback, very inefficient since we keep all struct sk_buff
around. So drivers enabling GRO but delivering linear skbs to network
stack aren't enabling full GRO power.

2) splice(socket -> pipe).

 We must copy the linear part to a page fragment.
 This kind of defeats splice() purpose (zero copy claim)

3) TCP coalescing.

 Recently introduced, this permits to group several contiguous segments
into a single skb. This shortens queue lengths and save kernel memory,
and greatly reduce probabilities of TCP collapses. This coalescing
doesnt work on linear skbs (or we would need to copy data, this would be
too slow)

Given all these issues, the following patch introduces the possibility
of having skb->head be a fragment in itself. We use a new skb flag,
skb->head_frag to carry this information.

build_skb() is changed to accept a frag_size argument. Drivers willing
to provide a page fragment instead of kmalloc() data will set a non zero
value, set to the fragment size.

Then, on situations we need to convert the skb head to a frag in itself,
we can check if skb->head_frag is set and avoid the copies or various
fallbacks we have.

This means drivers currently using frags could be updated to avoid the
current skb->head allocation and reduce their memory footprint (aka skb
truesize). (thats 512 or 1024 bytes saved per skb). This also makes
bpf/netfilter faster since the 'first frag' will be part of skb linear
part, no need to copy data.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that encap_rcv() works on IPv6 UDP sockets, wire L2TP up to IPv6.
Support has been tested with and without hardware offloading.  This
version fixes the L2TP over localhost issue with incorrect checksums
being reported.
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the sematics of udpv6_queue_rcv_skb() match IPv4's
udp_queue_rcv_skb(), introduce the UDP encap_rcv() hook for IPv6.
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quoting Tore Anderson from :
https://bugzilla.kernel.org/show_bug.cgi?id=42572

When RTAX_FEATURE_ALLFRAG is set on a route, the effective TCP segment
size does not take into account the size of the IPv6 Fragmentation
header that needs to be included in outbound packets, causing every
transmitted TCP segment to be fragmented across two IPv6 packets, the
latter of which will only contain 8 bytes of actual payload.

RTAX_FEATURE_ALLFRAG is typically set on a route in response to
receving a ICMPv6 Packet Too Big message indicating a Path MTU of less
than 1280 bytes. 1280 bytes is the minimum IPv6 MTU, however ICMPv6
PTBs with MTU < 1280 are still valid, in particular when an IPv6
packet is sent to an IPv4 destination through a stateless translator.
Any ICMPv4 Need To Fragment packets originated from the IPv4 part of
the path will be translated to ICMPv6 PTB which may then indicate an
MTU of less than 1280.

The Linux kernel refuses to reduce the effective MTU to anything below
1280 bytes, instead it sets it to exactly 1280 bytes, and
RTAX_FEATURE_ALLFRAG is also set. However, the TCP segment size appears
to be set to 1240 bytes (1280 Path MTU - 40 bytes of IPv6 header),
instead of 1232 (additionally taking into account the 8 bytes required
by the IPv6 Fragmentation extension header).

This in turn results in rather inefficient transmission, as every
transmitted TCP segment now is split in two fragments containing
1232+8 bytes of payload.

After this patch, all the outgoing packets that includes a
Fragmentation header all are "atomic" or "non-fragmented" fragments,
i.e., they both have Offset=0 and More Fragments=0.

With help from David S. Miller
Reported-by: NTore Anderson <tore@fud.no>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Tom Herbert <therbert@google.com>
Tested-by: NTore Anderson <tore@fud.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't pick __u8/__u16 values directly from raw pointers, but instead use
an array of structures of code:value pairs. This is OK, since the buffer
we take options from is not an skb memory, but a user-to-kernel one.

For those options which don't require any value now, require this to be
zero (for potential future extension of this API).

v2: Changed tcp_repair_opt to use two __u32-s as spotted by David Laight.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

read only, so change it to const.
Signed-off-by: NShan Wei <davidshan@tencent.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sk_add_backlog() & sk_rcvqueues_full() hard coded sk_rcvbuf as the
memory limit. We need to make this limit a parameter for TCP use.

No functional change expected in this patch, all callers still using the
old sk_rcvbuf limit.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Randy Dunlap <rdunlap@xenotime.net> reported:

> On 04/23/2012 12:07 AM, Stephen Rothwell wrote:
>
>> Hi all,
>>
>> Changes since 20120420:
>
>
> include/net/ax25.h:447:75: error: expected ';' before '}' token
>
> static inline int ax25_register_dev_sysctl(ax25_dev *ax25_dev) { return 0 };
> static inline void ax25_unregister_dev_sysctl(ax25_dev *ax25_dev) {};
>
> First function:  move ';' inside braces.
> Second function:  drop the ';'.

Put the semicolons where it makes sense.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Randy Dunlap <rdunlap@xenotime.net> reported:
> On 04/23/2012 12:07 AM, Stephen Rothwell wrote:
>
>> Hi all,
>>
>> Changes since 20120420:
>
>
>
> ERROR: "unregister_net_sysctl_table" [net/phonet/phonet.ko] undefined!
> ERROR: "register_net_sysctl" [net/phonet/phonet.ko] undefined!
>
> when CONFIG_SYSCTL is not enabled.

Add static inline stub functions to gracefully handle the case when sysctl
support is not present.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ieee80211_ave_rssi need to be declare as export for driver to use it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is meant typically to allow a PIC driver's irq domain map() callback
to establish sane defaults for the interrupt (and make sure that the HW
and the irq_desc are in sync as far as the trigger is concerned).

The irq core may not call the set_trigger callback if it thinks the
trigger is already set to the right setting, so we need to ensure new
descriptors are properly synchronized with the hardware.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This commit moves the (substantial) common code shared between
tcp_v4_init_sock() and tcp_v6_init_sock() to a new address-family
independent function, tcp_init_sock().

Centralizing this functionality should help avoid drift issues,
e.g. where the IPv4 side is updated without a corresponding update to
IPv6. There was already some drift: IPv4 initialized snd_cwnd to
TCP_INIT_CWND, while the IPv6 side was still initializing snd_cwnd to
2 (in this case it should not matter, since snd_cwnd is also
initialized in tcp_init_metrics(), but the general risks and
maintenance overhead remain).

When diffing the old and new code, note that new tcp_init_sock()
function uses the order of steps from the tcp_v4_init_sock()
implementation (the order is slightly different in
tcp_v6_init_sock()).
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes content of hashlist (used to get port struct by
computed index (0...en_port_count-1)). Now the hash list contains only
enabled ports so userspace will be able to say what ports can be used
for tx/rx. This becomes handy when userspace will need to disable ports
which does not belong to active aggregator. By default, newly added port
is enabled.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are options, which are set up on a socket while performing
TCP handshake. Need to resurrect them on a socket while repairing.
A new sockoption accepts a buffer and parses it. The buffer should
be CODE:VALUE sequence of bytes, where CODE is standard option
code and VALUE is the respective value.

Only 4 options should be handled on repaired socket.

To read 3 out of 4 of these options the TCP_INFO sockoption can be
used. An ability to get the last one (the mss_clamp) was added by
the previous patch.

Now the restore. Three of these options -- timestamp_ok, mss_clamp
and snd_wscale -- are just restored on a coket.

The sack_ok flags has 2 issues. First, whether or not to do sacks
at all. This flag is just read and set back. No other sack  info is
saved or restored, since according to the standart and the code
dropping all sack-ed segments is OK, the sender will resubmit them
again, so after the repair we will probably experience a pause in
connection. Next, the fack bit. It's just set back on a socket if
the respective sysctl is set. No collected stats about packets flow
is preserved. As far as I see (plz, correct me if I'm wrong) the
fack-based congestion algorithm survives dropping all of the stats
and repairs itself eventually, probably losing the performance for
that period.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This includes (according the the previous description):

* TCP_REPAIR sockoption

This one just puts the socket in/out of the repair mode.
Allowed for CAP_NET_ADMIN and for closed/establised sockets only.
When repair mode is turned off and the socket happens to be in
the established state the window probe is sent to the peer to
'unlock' the connection.

* TCP_REPAIR_QUEUE sockoption

This one sets the queue which we're about to repair. The
'no-queue' is set by default.

* TCP_QUEUE_SEQ socoption

Sets the write_seq/rcv_nxt of a selected repaired queue.
Allowed for TCP_CLOSE-d sockets only. When the socket changes
its state the other seq-s are changed by the kernel according
to the protocol rules (most of the existing code is actually
reused).

* Ability to forcibly bind a socket to a port

The sk->sk_reuse is set to SK_FORCE_REUSE.

* Immediate connect modification

The connect syscall initializes the connection, then directly jumps
to the code which finalizes it.

* Silent close modification

The close just aborts the connection (similar to SO_LINGER with 0
time) but without sending any FIN/RST-s to peer.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is just the preparation patch, which makes the needed for
TCP repair code ready for use.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

it's always current->mm
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

All of the users have been converted to use registera_net_sysctl so we
no longer need register_net_sysctl.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't use struct ctl_path anymore so delete the exported constants.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There isn't much advantage here except that strings paths are a bit
easier to read, and converting everything to them allows me to kill off
ctl_path.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sysctl core no longer natively understands sysctl tables
with .child entries.

Split the ipv6_table to remove the .child entries.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't register/unregister every ax25 table in a batch.  Instead register
and unregister per device ax25 sysctls as ax25 devices come and go.

This moves ax25 to be a completely modern sysctl user.  Registering the
sysctls in just the initial network namespace, removing the use of
.child entries that are no longer natively supported by the sysctl core
and taking advantage of the fact that there are no longer any ordering
constraints between registering and unregistering different sysctl
tables.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sysctl no longer requires explicit creation of directories.  The neigh
directory is always populated with at least a default entry so this
won't cause any user visible changes.

Delete the ipv4_path and the ipv4_skeleton these are no longer needed.

Directly register the ipv4_route_table.

And since I am an idiot remove the header definitions that I should
have removed in the previous patch.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

register_sysctl_rotable never caught on as an interesting way to
register sysctls.  My take on the situation is that what we want are
sysctls that we can only see in the initial network namespace.  What we
have implemented with register_sysctl_rotable are sysctls that we can
see in all of the network namespaces and can only change in the initial
network namespace.

That is a very silly way to go.  Just register the network sysctls
in the initial network namespace and we don't have any weird special
cases to deal with.

The sysctls affected are:
/proc/sys/net/ipv4/ipfrag_secret_interval
/proc/sys/net/ipv4/ipfrag_max_dist
/proc/sys/net/ipv6/ip6frag_secret_interval
/proc/sys/net/ipv6/mld_max_msf

I really don't expect anyone will miss them if they can't read them in a
child user namespace.

CC: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the netfilter code is modified to use register_net_sysctl_table the
kernel fails to boot because the per net sysctl infrasturce is not setup
soon enough.  So to avoid races call net_sysctl_init from sock_init().
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now all of the networking sysctl registrations are running in a
compatibiity mode.  The natvie sysctl registration api takes a cstring
for a path and a simple ctl_table.  Implement register_net_sysctl so
that we can register network sysctls without needing to use
compatiblity code in the sysctl core.

Switching from a ctl_path to a cstring results in less boiler plate
and denser code that is a little easier to read.

I would simply have changed the arguments to register_net_sysctl_table
instead of keeping two functions in parallel but gcc will allow a
ctl_path pointer to be passed to a char * pointer with only issuing a
warning resulting in completely incorrect code can be built.  Since I
have to change the function name I am taking advantage of the situation
to let both register_net_sysctl and register_net_sysctl_table live for a
short time in parallel which makes clean conversion patches a bit easier
to read and write.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.

Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.htmlSigned-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: NHebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NUlf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.

This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c.  But that way we don't have
to export our internal do_mmap_pgoff() function.

Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead.  We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Like the vm_brk() function, this is the same as "do_munmap()", except it
does the VM locking for the caller.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It does the same thing as "do_brk()", except it handles the VM locking
too.

It turns out that all external callers want that anyway, so we can make
do_brk() static to just mm/mmap.c while at it.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>