Traditionally, any System-on-Chip based platform creates a flat list
of platform_devices directly under /sys/devices/platform.

In order to give these some better structure, this introduces a new
bus type for soc_devices that are registered with the new
soc_device_register() function.  All devices that are on the same
chip should then be registered as child devices of the soc device.

The soc bus also exports a few standardised device attributes which
allow user space to query the specific type of soc.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This cuts down on the boilerplate code.

Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch introduces the module_pci_driver macro which is a convenience
macro for PCI driver modules similar to module_platform_driver. It is
intended to be used by drivers which init/exit section does nothing but
register/unregister the PCI driver. By using this macro it is possible
to eliminate a few lines of boilerplate code per PCI driver.

Based on work done by Lars-Peter Clausen <lars@metafoo.de> for other
busses (i2c and spi).

Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Direct inclusion of the asm header has long been deprecated by the
introduction of gpiolib.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current code arbirarily limited the number of CPUs the guest could have.
Change that so that we can support the maximum number of CPUs the guest can
support. While we use NR_CPUS to size the per-cpu state all we are allocating
based on NR_CPUS are the  pointers to per-cpu state that will be allocatted in
the context of the initializing CPU. This patch triggers a checkpatch warning
for the usage of NR_CPU and since all we are allocating a couple of pointers
per CPU, it should be ok.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now, cleanup the user/kernel KVP protocol by using the same structure
definition that is used for host/guest KVP protocol. This simplifies the code.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now use hyperv.h to get the KVP defines in the KVP user-mode code.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now cleanup the hyperv.h with regards to KVP definitions.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When checking driver-core tree, found crazying warnings on my setups.

[  216.025849] calling  acpi_processor_init+0x0/0x81 @ 1
[  216.045332] ACPI: Requesting acpi_cpufreq
[  216.047454] Monitor-Mwait will be used to enter C-1 state
[  216.047912] Monitor-Mwait will be used to enter C-3 state
[  216.065270] ACPI: acpi_idle registered with cpuidle
[  216.068241] kobject (ffff8870364a1940): tried to init an initialized object, something is seriously wrong.
[  216.085287] Pid: 1, comm: swapper/0 Not tainted 3.3.0-rc2-tip-yh-02428-ge663840-dirty #247
[  216.105041] Call Trace:
[  216.105192]  [<ffffffff813a9c06>] kobject_init+0x33/0x83
[  216.124880]  [<ffffffff813aa1f8>] kobject_init_and_add+0x23/0x57
[  216.125158]  [<ffffffff819f3a08>] cpuidle_add_sysfs+0x49/0x62
[  216.144850]  [<ffffffff819f2a28>] __cpuidle_register_device+0xe6/0x10e
[  216.145182]  [<ffffffff819f2ea4>] cpuidle_register_device+0x25/0x4d
[  216.164912]  [<ffffffff81cb5774>] acpi_processor_power_init+0x13e/0x16c
[  216.165205]  [<ffffffff81427620>] ? acpi_processor_get_throttling_info+0x128/0x158
[  216.185012]  [<ffffffff81c68ae5>] acpi_processor_start+0x62/0x11d
[  216.204861]  [<ffffffff81cb55ff>] acpi_processor_add+0x1b0/0x1e7
[  216.205144]  [<ffffffff81402a7e>] acpi_device_probe+0x4e/0x11c
[  216.225063]  [<ffffffff8148f0e7>] really_probe+0x99/0x126
[  216.225328]  [<ffffffff8148f2a3>] driver_probe_device+0x3b/0x56
[  216.244846]  [<ffffffff8148f31d>] __driver_attach+0x5f/0x82
[  216.245101]  [<ffffffff8148f2be>] ? driver_probe_device+0x56/0x56
[  216.264668]  [<ffffffff8148db80>] bus_for_each_dev+0x5c/0x88
[  216.264942]  [<ffffffff8148eea7>] driver_attach+0x1e/0x20
[  216.284639]  [<ffffffff8148eaec>] bus_add_driver+0xca/0x21d
[  216.284903]  [<ffffffff81095827>] ? local_clock+0xf/0x3c
[  216.304580]  [<ffffffff82814177>] ? acpi_fan_init+0x18/0x18
[  216.304849]  [<ffffffff8148f79b>] driver_register+0x91/0xfe
[  216.324545]  [<ffffffff82814177>] ? acpi_fan_init+0x18/0x18
[  216.324813]  [<ffffffff81403705>] acpi_bus_register_driver+0x43/0x45
[  216.344563]  [<ffffffff828141a7>] acpi_processor_init+0x30/0x81
[  216.344845]  [<ffffffff82814177>] ? acpi_fan_init+0x18/0x18
[  216.364590]  [<ffffffff810001e7>] do_one_initcall+0x57/0x134
[  216.364868]  [<ffffffff827e6f8c>] kernel_init+0x146/0x1c0
[  216.384512]  [<ffffffff81d03aa4>] kernel_thread_helper+0x4/0x10
[  216.384819]  [<ffffffff81cfbb5d>] ? retint_restore_args+0xe/0xe
[  216.404578]  [<ffffffff827e6e46>] ? start_kernel+0x3ab/0x3ab
[  216.424530]  [<ffffffff81d03aa0>] ? gs_change+0xb/0xb
[  216.424793] ------------[ cut here ]------------
[  216.425038] WARNING: at fs/sysfs/dir.c:502 sysfs_add_one+0x97/0xab()
[  216.444480] Hardware name: Sun Fire X4800
[  216.444668] sysfs: cannot create duplicate filename '/devices/system/cpu/cpu0/cpuidle'
...

It turns out acpi_processor_power_init() get called two time in acpi_processor_add and acpi_processor_start.

Found several lines are duplicated in those two functions even related commit move them.

The related patches are ok.  Not sure how it could happen, looks like git problem.

-v2: add back acpi_processor_load_module(pr) to acpi_processor_load_start
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: NThomas Renninger <trenn@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Someone forgot to test this one it seems.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation for consolidating all KVP related defines into a single header file
that both the kernel and user level components can use, move the contents of
hv_kvp.h into hyperv.h.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current KVP code carries some private connector related defines.
Update connector.h to have all the KVP defines. As part of this patch
get rid of some unused defines.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes a bug introduced with sysfs name hashes where renaming a
network device appears to succeed but silently makes the sysfs files for
that network device inaccessible.

In at least one configuration this bug has stopped networking from
coming up during boot.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Tested-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are few important bug fixes for LogFS

* tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream:
  Logfs: Allow NULL block_isbad() methods
  logfs: Grow inode in delete path
  logfs: Free areas before calling generic_shutdown_super()
  logfs: remove useless BUG_ON
  MAINTAINERS: Add Prasad Joshi in LogFS maintiners
  logfs: Propagate page parameter to __logfs_write_inode
  logfs: set superblock shutdown flag after generic sb shutdown
  logfs: take write mutex lock during fsync and sync
  logfs: Prevent memory corruption
  logfs: update page reference count for pined pages

Fix up conflict in fs/logfs/dev_mtd.c due to semantic change in what
"mtd->block_isbad" means in commit f2933e86: "Logfs: Allow NULL
block_isbad() methods" clashing with the abstraction changes in the
commits 7086c19d: "mtd: introduce mtd_block_isbad interface" and
d58b27ed: "logfs: do not use 'mtd->block_isbad' directly".

This resolution takes the semantics from commit f2933e86, and just
makes mtd_block_isbad() return zero (false) if the 'block_isbad'
function is NULL.  But that also means that now "mtd_can_have_bb()"
always returns 0.

Now, "mtd_block_markbad()" will obviously return an error if the
low-level driver doesn't support bad blocks, so this is somewhat
non-symmetric, but it actually makes sense if a NULL "block_isbad"
function is considered to mean "I assume that all my blocks are always
good".

Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (w83627ehf) Disable setting DC mode for pwm2, pwm3 on NCT6776F
  hwmon: (sht15) fix bad error code
  MAINTAINERS: Drop maintainer for MAX1668 hwmon driver
  MAINTAINERS: Add hwmon entries for Wolfson
  hwmon: (f71805f) Fix clamping of temperature limits

Here are some fixes to the pin control system that has accumulated since
-rc1.  Mainly Tony Lindgren fixed the module load/unload logic and the
rest are minor fixes and documentation.

* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: add checks for empty function names
  pinctrl: fix pinmux_hog_maps when ctrl_dev_name is not set
  pinctrl: fix some pinmux typos
  pinctrl: free debugfs entries when unloading a pinmux driver
  pinctrl: unbreak error messages
  Documentation/pinctrl: fix a few syntax errors in code examples
  pinctrl: fix pinconf_pins_show iteration

Here are some tty/serial patches for 3.3-rc1

Big thing here is the movement of the 8250 serial drivers to their own
directory, now that the patch churn has calmed down.

Other than that, only minor stuff (omap patches were reverted as they
were found to be wrong), and another broken driver removed from the
system.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* tag 'tty-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: Kill off Moorestown code
  Revert "tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode"
  Revert "tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip"
  serial: Fix wakeup init logic to speed up startup
  docbook: don't use serial_core.h in device-drivers book
  serial: amba-pl011: lock console writes against interrupts
  amba-pl011: do not disable RTS during shutdown
  tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip
  tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode
  omap-serial: make serial_omap_restore_context depend on CONFIG_PM_RUNTIME
  omap-serial :Make the suspend/resume functions depend on CONFIG_PM_SLEEP.
  TTY: fix UV serial console regression
  jsm: Fixed EEH recovery error
  Updated TTY MAINTAINERS info
  serial: group all the 8250 related code together

Here are a bunch of USB patches for 3.3-rc1.

Nothing major, largest thing here is the removal of some drivers that
did not work at all.  Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (52 commits)
  uwb & wusb: fix kconfig error
  USB: Realtek cr: fix autopm scheduling while atomic
  USB: ftdi_sio: Add more identifiers
  xHCI: Cleanup isoc transfer ring when TD length mismatch found
  usb: musb: omap2430: minor cleanups.
  qcaux: add more Pantech UML190 and UML290 ports
  Revert "drivers: usb: Fix dependency for USB_HWA_HCD"
  usb: mv-otg - Fix build if CONFIG_USB is not set
  USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPE
  usb: add support for STA2X11 host driver
  drivers: usb: Fix dependency for USB_HWA_HCD
  kernel-doc: fix new warning in usb.h
  USB: OHCI: fix new compiler warnings
  usb: serial: kobil_sct: fix compile warning:
  drivers/usb/host/ehci-fsl.c: add missing iounmap
  USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core
  USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removal
  USB: cdc-wdm: use two mutexes to allow simultaneous read and write
  USB: cdc-wdm: updating desc->length must be protected by spin_lock
  USB: usbsevseg: fix max length
  ...

1) Setting link attributes can modify the size of the attributes that
   would be reported on a subsequent getlink netlink operation,
   therefore min_ifinfo_dump_size needs to be adjusted.  From Stefan
   Gula.

2) Resegmentation of TSO frames while trimming can violate invariants
   expected by callers, namely that the number of segments can only stay
   the same or decrease, never increase.  If MSS changes, however, we
   can trim data but then end up with more segments.  Fix this by only
   segmenting to the MSS already recorded in the SKB.  That's the
   simplest fix for now and if we want to get more fancy in the future
   that's a more involved change.

   This probably explains some retransmit counter inaccuracies.

   From Neal Cardwell.

3) Fix too-many-wakeups in POLL with AF_UNIX sockets, from Eric Dumazet.

4) Fix CAIF crashes wrt.  namespace handling.  From Eric Dumazet and
   Eric W. Biederman.

5) TCP port selection fixes from Flavio Leitner.

6) More socket memory cgroup build fixes in certain randonfig
   situations.  From Glauber Costa.

7) Fix TCP memory sysctl regression reported by Ingo Molnar, also from
   Glauber Costa.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  af_unix: fix EPOLLET regression for stream sockets
  tcp: fix tcp_trim_head() to adjust segment count with skb MSS
  net/tcp: Fix tcp memory limits initialization when !CONFIG_SYSCTL
  net caif: Register properly as a pernet subsystem.
  netns: Fail conspicously if someone uses net_generic at an inappropriate time.
  net: explicitly add jump_label.h header to sock.h
  net: RTNETLINK adjusting values of min_ifinfo_dump_size
  ipv6: Fix ip_gre lockless xmits.
  xen-netfront: correct MAX_TX_TARGET calculation.
  netns: fix net_alloc_generic()
  tcp: bind() optimize port allocation
  tcp: bind() fix autoselection to share ports
  l2tp: l2tp_ip - fix possible oops on packet receive
  iwlwifi: fix PCI-E transport "inta" race
  mac80211: set bss_conf.idle when vif is connected
  mac80211: update oper_channel on ibss join

This fixes an integration issue with the regulator device tree bindings
which shook out in -rc.  The bindings were overly enthusiatic when
deciding to set a voltage on a regulator and would try to set zero volts
on an unconfigured regulator which isn't supported.

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: Set apply_uV only when min and max voltages are defined

Commit 0884d7aa (AF_UNIX: Fix poll blocking problem when reading from
a stream socket) added a regression for epoll() in Edge Triggered mode
(EPOLLET)

Appropriate fix is to use skb_peek()/skb_unlink() instead of
skb_dequeue(), and only call skb_unlink() when skb is fully consumed.

This remove the need to requeue a partial skb into sk_receive_queue head
and the extra sk->sk_data_ready() calls that added the regression.

This is safe because once skb is given to sk_receive_queue, it is not
modified by a writer, and readers are serialized by u->readlock mutex.

This also reduce number of spinlock acquisition for small reads or
MSG_PEEK users so should improve overall performance.
Reported-by: NNick Mathewson <nickm@freehaven.net>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Alexey Moiseytsev <himeraster@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit fixes tcp_trim_head() to recalculate the number of
segments in the skb with the skb's existing MSS, so trimming the head
causes the skb segment count to be monotonically non-increasing - it
should stay the same or go down, but not increase.

Previously tcp_trim_head() used the current MSS of the connection. But
if there was a decrease in MSS between original transmission and ACK
(e.g. due to PMTUD), this could cause tcp_trim_head() to
counter-intuitively increase the segment count when trimming bytes off
the head of an skb. This violated assumptions in tcp_tso_acked() that
tcp_trim_head() only decreases the packet count, so that packets_acked
in tcp_tso_acked() could underflow, leading tcp_clean_rtx_queue() to
pass u32 pkts_acked values as large as 0xffffffff to
ca_ops->pkts_acked().

As an aside, if tcp_trim_head() had really wanted the skb to reflect
the current MSS, it should have called tcp_set_skb_tso_segs()
unconditionally, since a decrease in MSS would mean that a
single-packet skb should now be sliced into multiple segments.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NNandita Dukkipati <nanditad@google.com>
Acked-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sysctl_tcp_mem() initialization was moved to sysctl_tcp_ipv4.c
in commit 3dc43e3e, since it
became a per-ns value.

That code, however, will never run when CONFIG_SYSCTL is
disabled, leading to bogus values on those fields - causing hung
TCP sockets.

This patch fixes it by keeping an initialization code in
tcp_init(). It will be overwritten by the first net namespace
init if CONFIG_SYSCTL is compiled in, and do the right thing if
it is compiled out.

It is also named properly as tcp_init_mem(), to properly signal
its non-sysctl side effect on TCP limits.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NGlauber Costa <glommer@parallels.com>
Cc: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/4F22D05A.8030604@parallels.com
[ renamed the function, tidied up the changelog a bit ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  [S390] dasd: revalidate server for new pathgroup
  [S390] dasd: revert LCU optimization
  [S390] cleanup entry point definition

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: generic atomic64 support

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  vmwgfx: Fix assignment in vmw_framebuffer_create_handle
  drm/radeon/kms: Fix device tree linkage of i2c buses
  drm: Pass the real error code back during GEM bo initialisation
  Revert "drm/i810: cleanup reclaim_buffers"

NFS client bugfixes for Linux 3.3 (pull 3)

* tag 'nfs-for-3.3-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  SUNRPC: Fix machine creds in generic_create_cred and generic_match

Power management fix for 3.3-rc2

Fix for a hibernate (s2disk) regression introduced during the 3.2
merge window that causes s2disk to trigger BUG_ON() in
freeze_workqueues_begin() if there is not enough swap space to save
the image.

* tag 'pm-fix-for-3.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / Hibernate: Fix s2disk regression related to freezing workqueues

The assignment of handle in vmw_framebuffer_create_handle doesn't actually do anything useful and is incorrectly assigning an integer value to a pointer argument. It appears that this is a typo and should be dereferencing handle rather than assigning to it directly. This fixes a bug where an undefined handle value is potentially returned to user-space.
Signed-off-by: NRyan Mallon <rmallon@gmail.com>
Reviewed-by: Jakob Bornecrantz<jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Properly set the parent device of i2c buses before registering them so
that they will show at the right place in the device tree (rather than
in /sys/devices directly.)
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In particular, I found I was hitting the max-file limit in the VFS,
and the EFILE was being magically transformed into ENOMEM. Confusion
reigns.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 87499ffd.

Where is that paper bag ... ah here.

I've failed to take an odd interaction between my other cleanups and
this reclaim_buffers patch into account and also failed to properly
test it. Looks like there are more dragons and hidden trapdoors in the
drm release path than actual lines of code.

Until I get a clue, let's just revert this.
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

NCT6776F only supports pwm mode for pwm2 and pwm3. Return error if an attempt
is made to set those pwm channels to DC mode.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Commit 2aede851

  PM / Hibernate: Freeze kernel threads after preallocating memory

introduced a mechanism by which kernel threads were frozen after
the preallocation of hibernate image memory to avoid problems with
frozen kernel threads not responding to memory freeing requests.
However, it overlooked the s2disk code path in which the
SNAPSHOT_CREATE_IMAGE ioctl was run directly after SNAPSHOT_FREE,
which caused freeze_workqueues_begin() to BUG(), because it saw
that worqueues had been already frozen.

Although in principle this issue might be addressed by removing
the relevant BUG_ON() from freeze_workqueues_begin(), that would
reintroduce the very problem that commit 2aede851
attempted to avoid into that particular code path.  For this reason,
to fix the issue at hand, introduce thaw_kernel_threads() and make
the SNAPSHOT_FREE ioctl execute it.

Special thanks to Srivatsa S. Bhat for detailed analysis of the
problem.
Reported-and-tested-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: stable@kernel.org

When no platform data was supplied, returned error code was 0.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 2.6.32+
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Merge tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Here are some patches for the 3.3-rc1 tree.

It contains the removal of the sysdev code, now that all users of it are
gone, as well as some sysfs bugfixes that have been reported by users.
There are also some documentation updates here as well.

* tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  sysfs: Complain bitterly about attempts to remove files from nonexistent directories.
  stable: update documentation to ask for kernel version
  base/core.c:fix typo in comment in function device_add
  Documentation: devres: add allocation functions to list of supported calls
  Documentation update for the driver model core
  kernel-doc: fix new warnings in driver-core
  kernel-doc: fix new warnings in debugfs
  kernel-doc: fix new warnings in device.h
  driver core: remove drivers/base/sys.c and include/linux/sysdev.h

* tag 'for-linus' of git://github.com/rustyrussell/linux:
  lguest: remove reference from Documentation/virtual/00-INDEX
  virtio: correct the memory barrier in virtqueue_kick_prepare()
  virtio: fix typos of memory barriers

Merge branch 'stable/for-linus-fixes-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

* 'stable/for-linus-fixes-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/granttable: Disable grant v2 for HVM domains.
  x86: xen: size struct xen_spinlock to always fit in arch_spinlock_t