As for most of the users the 1.10 firmware is an improvement we should
use this firmware always now.
Signed-off-by: NPatrick Boettcher <pb@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This is a minor change to help with tracking the viability of the
encoder chip within the PVR USB2 device.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMarco Schluessler <marco@lordzodiac.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Someone added a new case without adding a break to the one before it.

Thanks to Margus <b-berski at mbox200 dot swipnet dot se> for spotting this.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Coverity (CID 1929) spotted the following: if a transfer buffer
allocation fails, the last allocated urb is leaked (it hasn't been
stored in dev->urb[] yet so em28xx_uninit_isoc misses it). The patch
also includes a small typo fix.
Signed-off-by: NFlorin Malita <fmalita@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When the radio is active the video should be muted when a capture
starts. However, this was done at the wrong time and the mute settings
were overwritten when cx2341x_update was called.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If the ivtvfb module isn't loaded, the valid YUV output area should be set to
full-screen. This patch fixes the case where the valid output area was not
reset when the output broadcast format was changed from NTSC to PAL. This
resulted in output being limited to the top 480 lines of the display.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When the ivtvfb module is loaded, the YUV output is relative to the
framebuffer output. When a virtual screen size is used, the output area for
the YUV may actually be off screen. To prevent the hardware from crashing,
the current driver will ignore an off-screen position and leave the output
visible at the last on-screen position. This may not be desirable, so this
patch will switch off the YUV output should the image move off-screen, and
re-enable it should the image move on-screen again.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Prevent unloading the framebuffer if it is still in use.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If you try to access the video device from within an udev rule,
then you get into a circular locking situation.

Changed the driver to postpone the registration of the devices until
everything else has been fully initialized, so that the newly created
device can be used immediately.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Resizing an MPEG 1 stream would cut off the right half of the
image due to a missing divide by 2 in VIDIOC_S_FMT.

Also did some minor cleanup in this part of the code.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch partially reverts a previous change that caused the
CX2341X_OSD_SET_PIXEL_FORMAT firmware calls to be skipped when the pixel
format of the framebuffer wasn't altered by FBIOPUT_VSCREENINFO.

Unfortunately, another firmware call on the PVR350 sometimes scrambles the
display when trying to adjust the framebuffer settings. This patch re-enables
the CX2341X_OSD_SET_PIXEL_FORMAT calls to try and prevent this from
occurring.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Thanks-to: Martin Dauskardt <md001@gmx.de>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Trying to open the radio when a capture is in progress will make it
impossible to open the radio again since the radio stream wasn't released.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When a cx8802 sub-driver was unregistered, the struct cx8802_driver, which was
kmalloc()ed by cx8802_register_driver(), was deleted from the list of drivers,
but never freed.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Less code and more efficient.

Got ride of a variable that counted the number of devices in
cx8802_unregister_driver() but was never used.  Looked leftover from a
cut&paste.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It was a struct cx8802_driver for no apparent reason.  Nothing uses a
cx8802_driver in the cx8802_dev struct.  The only field that was used was
devlist, a list_head.

The code in cx8802_remove() that removed any loaded sub-drivers was broken.
It would delete the current list entry, but didn't use list_for_each_safe.  It
also called list_del() on the list _head_ inside the list_for_each loop?  It
would crash if it was run, which I don't think can ever happen.

Since the cx8802 sub-drivers use the cx8802 driver, they have to be unloaded
first.  So there isn't any way for a sub-driver to still be loaded when
cx8802_remove() is called...  Except maybe with PCI hot-plug, if one removes
the PCI card while the drivers are loaded?

So I left some code in to handle that if it's actually possible.  It will
remove the sub-drivers from the device cx8802_remove() was called on, and only
that device.  If one has two DVB cards and unplugs one, there is no reason to
unload the DVB drivers for both cards.  I have no way to test this, but it
can't be worse than what was there before.

cx8802_get_driver() is passed a cx8802_dev pointer and looks for the requested
driver on that device.  It first loops over the cx8802 device list looking for
the device it was passed, which is pointless.  It doesn't need to find the
device pointer in the list, as it already has the pointer.

The list_head in the cx8802_driver struct, which joins all the _drivers_
attached to a device, was named devlist.  Changed that to drvlist, since the
devlist is used for a list of _devices_ in other cx8802 structs.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

card_priv was only used to store a pointer to the vp3054 state struct.
There's no need to use a void * since it doesn't have multiple types.

Make the field conditional on VP3045 support.  It was already conditional on
DVB support, but it's only used if VP3045 support is on, so that makes for a
better option to check.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add some ifdefs around fields only used for blackbird support, similar to the
way the dvb fields are only included with dvb support.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

make tvaudio thread freezeable, and add proper support for that
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fixes few more problems I found in my saa7134 resume code:

* Race between IRQ handler and .suspend()/.resume() functions

* Removes timeout timers on active buffers - those
	buffers will be recaptured after resume

* Adds suspend/resume for IR code - probably
	necessary if using polling mode

* Adds #ifdef CONFIG_PM overs suspend code

* Runs  a quirk in set_tvnorm in suspend/resume too

* Rearranges the order of calls in saa7134_resume to
	be exactly as in saa7134_initdev thus the card is
	initialized in exactly the same way

* Since DMA audio capture suspend/resume isn't yet supported,
	avoid re-enabling it on resume for now
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We shouldn't dereference "itv" when we know it's NULL...

Spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Initialize strength to zero.

Thanks to Adrian Bunk, who spotted this with the Coverity checker.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Both cx23885_initdev and cx23885_dev_setup free the device in their
error path so a failure in the latter causes a double-free. Since
cx23885_dev_setup is only called from cx23885_initdev, it should be safe
to remove its deallocation and leave the cleanup up to the allocating
function.

Coverity CID 1922.
Signed-off-by: NFlorin Malita <fmalita@gmail.com>
CC: Steven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

As videobuf_cgmbuf is defined only if CONFIG_VIDEO_V4L1_COMPAT is enabled,
move the EXPORT_SYMBOL_GPL declaration inside the #ifdef block.  Fixes
compilation for x86_64 defconfig.
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

cinergyT2, remove bad usage of ERESTARTSYS

test of cinergyt2->disconnect_pending doesn't ensure pending signal and so
ERESTARTSYS would reach userspace, which is not permitted. Change it to
EAGAIN.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Remove the obsolete VIDIOC_G_MPEGCOMP and VIDIOC_S_MPEGCOMP ioctls from
the V4L2 API as per the removal schedule (October 2007).
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

struct video_device used to define a .hardware field. While
initialized on severl drivers, this field is never used inside V4L.
However, drivers using it need to include the old V4L1 header.

This seems to cause compilation troubles with some random configs.
Better just to remove it from all drivers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Remove obsolete V4L v1 reference.

Thanks to Ingo Molnar for pointing this issue.
Signed-off-by: NPekka Seppänen <pexu@kapsi.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Lets mixer apps display a dB range for the volume control.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add two mute controls.  One mutes everything, the other just mutes the analog
pass-through output.

Rename the existing volume control.  The controls are now:
Playback Volume
Playback Switch
Capture Switch

These names might seem odd, but I believe they are more correct.  The previous
"Capture Volume" control didn't actually effect the volume of the captured
audio.  Instead it controls the volume of the analog pass-thought output.  It
appears that pass-through controls like this are usually considered to be in
the playback direction, not capture.  For example, "CAPTURE feedback Playback
Volume" is the name used for a control that appears to have the same effect in
the ca0106 driver.  We only have one volume control, so we can omit the
"CAPTURE feedback" part.

If someone where to add PCM playback support to the driver, then this would be
the volume control.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
  Blackfin arch: update boards files
  Blackfin arch: dma add some API and cleanup bf54x DMA definition
  Blackfin arch: cleanup and promote the general purpose timers api to a core blackfin component
  Blackfin arch: add a cheesy install target
  Blackfin arch: add functions for converting between sclks and usecs
  Blackfin arch: add assembly function for doing 64bit unsigned division
  Blackfin arch: -mno-fdpic works
  Blackfin arch: use "char bfin_board_name[]" rather than "char *bfin_board_name" per discussion on lkml as the former uses less storage
  Blackfin arch: Fixing Bug: balance calls to get_task_mm with corresponding mmput calls
  Blackfin serial driver Kconfig: depend on DMA not being enabled rather than a specific DMA size
  Blackfin arch: Fix bug: missing CHIPID register field definition of BF54x
  Blackfin arch: Fix up /proc/cpuinfo so it is like everyone else
  Blackfin arch: Optimization - no need to make additional math here
  Blackfin arch: force irq_flags into the .data section
  Blackfin arch BF548 defconfig: enable watchdog by default
  Blackfin arch: add new processor ADSP-BF52x arch/mach support

* 'audit.b43' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  [PATCH] audit: watching subtrees
  [PATCH] new helper - inotify_evict_watch()
  [PATCH] new helper - inotify_clone_watch()
  [PATCH] new helpers - collect_mounts() and release_collected_mounts()
  [PATCH] pass dentry to audit_inode()/audit_inode_child()

This path mustn't have been tested :( I did attempt to exercise it
by injecting failures here, but I suspect PageMappedToDisk may have
been getting in the way. Will need more of a look, although I think
nobh mode is OK for an -rc1 (it shouldn't eat anyone's data).

Commit 03158cd7 ("fs: restore nobh")
introcduced a NULL deref.  Spotted by the Coverity checker.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>

Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>