Derive supported speeds from LMT field in the READ_CONFIG

Driver was keying off internal cores. Use what the firmware reports instead.
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Change version number to 8.1.2
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Modify RSCN handling to unregister rpis on lost FCP_TARGETs immediately
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Fix panic caused by HBA resets and target side cable pulls
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Fixed module parameter descriptions.
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Code cleanup of lpfc_mbx_cmpl_config_link
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Allow turning on internal loop-back mode
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Code style changes for Discovery code
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Make lpfc_els_rsp_rps_acc and lpfc_els_rsp_rpl_acc static
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Added support for FAN
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add ERROR and WARM_START modes for diagnostic purposes.
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Remove hba_list from struct lpfc_hba
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Correct use of the hostdata field in scsi_host
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Misc FC Discovery changes :
   - Added FC_BYPASSED_MODE statistic
   - Corrected some log message data
   - Fix up Discovery infrastructure to support FAN:
       Allow Fabric entities to flow thru DSM
       Fix up linkup/linkdown unregister login processing for Fabric entities
       Clean up Discovery code
       Utilize nodev_tmo for Fabric entities
   - Use of 3 * ratov for CT handling timeouts
   - Fix up DSM to make more appropriate decisions and clean up code.
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add module parameter to limit number of outstanding commands per lpfc HBA
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Fixed a double insertion of mail box object to the SLI mailbox list.
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Fixed system panic in lpfc_sli_brdreset during dynamic add of LP11K
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Explicitly initialize the skip_post argument to lpfc_sli_send_reset
  on a ERATT interrupt.
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Fixed a race condition in the PLOGI retry logic.
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Handling of ELS commands RRQ, RPS, RPL and LIRR correctly
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Remove unused SLI_IOCB_HIGH_PRIORITY
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Remove unreferenced cfg_fcp_bind_method from struct lpfc_hba
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Remove unused prototypes from lpfc_crtn.h
Signed-off-by: NJamie Wellnitz <Jamie.Wellnitz@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NJames Smart <James.Smart@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- Add functionality to run in polled mode only. Includes run time
  attribute to enable mode.
- Enable runtime writable hba settings for coallescing and delay parameters

Customers have requested a mode in the driver to run strictly polled.
This is generally to support an environment where the server is extremely
loaded and is looking to reclaim some cpu cycles from adapter interrupt
handling.

This patch adds a new "poll" attribute, and the following behavior:

if value is 0 (default):
  The driver uses the normal method for i/o completion. It uses the
  firmware feature of interrupt coalesing. The firmware allows a
  minimum number of i/o completions before an interrupt, or a maximum
  time delay between interrupts.  By default, the driver sets these
  to no delay (disabled) or 1 i/o - meaning coalescing is disabled.

  Attributes were provided to change the coalescing values, but it was
  a module-load time only and global across all adapters.
  This patch allows them to be writable on a per-adapter basis.

if value is 1 :
  Interrupts are left enabled, expecting that the user has tuned the
  interrupt coalescing values. When this setting is enabled, the driver
  will attempt to service completed i/o whenever new i/o is submitted
  to the adapter. If the coalescing values are large, and the i/o
  generation rate steady, an interrupt will be avoided by servicing
  completed i/o prior to the coalescing thresholds kicking in. However,
  if the i/o completion load is high enough or i/o generation slow, the
  coalescion values will ensure that completed i/o is serviced in a timely
  fashion.

if value is 3 :
  Turns off FCP i/o interrupts altogether. The coalescing values now have
  no effect. A new attribute "poll_tmo" (default 10ms) exists to set
  the polling interval for i/o completion. When this setting is enabled,
  the driver will attempt to service completed i/o and restart the
  interval timer whenever new i/o is submitted. This behavior allows for
  servicing of completed i/o sooner than the interval timer, but ensures
  that if no i/o is being issued, then the interval timer will kick in
  to service the outstanding i/o.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- Release task management command before counting outstanding commands.
  TMF was being erroneously counted as an active outstanding command.
- Serialize EH calls and block requests when EH function is running.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Remove locking wrappers around error handlers. Wrappers were added in
early 2.6.13 api change
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- Remove unnecessary scsi_block_requests calls on rport deletes.
  This was deadlocking the sdev removals as they wanted to flush commands.
- No longer block requests when adding the remote port (to block
  discovery). Instead, register, then change port role. Maps to Qlogic
  behavior, and closer to the register-node-upon-first-ELS behavior.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Cause: Link bounces were causing discovery ELS's to be killed.
Driver was not properly flushing ELS commands upon the subsequent
link bounces. Thus, processing of ELS post link bounce erroneously
assumed discovery failure and device loss.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Miscellaneous Cleanups:
- Remove ProgType READ_REV mailbox command value check in lpfc_config_port_prep.
- Convert simple printk to an lpfc_printf_log in queuecommand.
- Modify lpfc_abort_handler message 0749 to display more accurate text and data.
- Minor style cleanup: fix 3 long lines in lpfc_hw.h
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Current upstream 'allmodconfig' build is broken.  This is the obvious
patch...
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is the drivers/scsi/ part of the big kfree cleanup patch.

Remove pointless checks for NULL prior to calling kfree() in drivers/scsi/.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: NKai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use schedule_timeout_uninterruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>