Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

here we check for BT state and if BT calibration has started,
give 25ms for BT Calibration to finish. we also take care of 2G/5G
switch and LNA transfer incase WLAN is operating in 5G. in case the BT
state is awake when we do WLAN calibration re-calibrate and we reset
the message exchange between WLAN and BT. BT is given preference when
simultaneous CAL request happens. calibration for WLAN/BT is done
assuming that the other co-existing module is in awake state, if not
we continue to do calibration while if the other module's state changes
we need to do restart the calibration handshake

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WLAN communicates with BT for its calibration by sending WLAN_CAL_REQ,
waits for BT_CAL_GRANT. This is done with the help of GPM messages.
also WLAN_CAL_DONE messages is sent once WLAN calibration is done.

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

send halt BT GPM if the chip is in network sleep and BT state
is awake

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

required buffers and dma allocation is done for GPM and SCHED
messages

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

check for the condition of MCI interrupt being triggered and
appropriately obtain the values of MCI_INTERRUPT_RX_MSG_RAW and
MCI_INTERRUPT_RAW

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

MCI interrupt is an asynchronous one, so take care of it by having a
check in ath9k_hw_intrpend, which actually decides whether the interrupt
is really for the driver from ath_isr

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

enable MCI interrupt when ath9k_hw_enable_interrupts is called,
like during the completion of chip_reset before which the interrupts
are disabled

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

these parameter will be utilized and modified in the MCI hardware codes
state machine

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

these definitions will be used by MCI state machine and the corresponding
hardware code

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

change the AR_DEF_ANTENNA register settings i.e setting default antenna
setting only for antenna diversity enabled chipsets. no point in
doing this for MIMO chipsets
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

GPIO pin 4 is assigned AR9462 chipsets LED.
while GPIO pin 0 worked for obselete AR9462 chipsets though
they are meant for EEPROM as per Russell

Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRussell Hu <rhu@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Optimize ath5k_cw_validate by using the classic (X & (X - 1)) == 0
check to see if a number is power of 2.

v2: Use functions from log2.h instead
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to documentation higher DCUs have higher priority and should
be used for beacons and CAB traffic. More specifically DCU 9 should be
used for beacons and DCU 8 for CAB traffic, I assumed DCU 7 should be
OK for UAPSD traffic.

Note that DCU 8 and 9 are special because they can only be mapped to a single
QCU each but since we use a 1:1 mapping between QCUs and DCUs anyway we don't
have to change much.

P.S. I also did a few related cleanups on qcu.c and ath5k.h
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No need to take ath5k_hw as an argument.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

MRR support and 2GHz radio override belong in ah_capabilities and we
should use them (e.g. so far  we used to set mrr descriptor without
checking if MRR support is enabled + we checked for MRR support 2
times, one by trying to set up an MRR descriptor and another one based
on MAC version).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a module parameter to disable hw rf kill switch (GPIO interrupt) because
in some cases when the card doesn't come with the laptop, EEPROM configuration
doesn't match laptop's configuration and rf kill interrupt always fires up and
disables hw. I thought of moving this to debugfs and make it per-card but
this way it's easier for users and distros to handle.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no short calibration on AR5210, make sure we treat it always
as full calibration.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No functional changes

Add kernel doc for all ath5k_hw_* functions and strcucts. Also do some cleanup,
rename ath5k_hw_init_beacon to ath5k_hw_init_beacon_timers, remove an unused
variable from ath5k_hw_pcu_init and a few obsolete macros, mostly related to XR.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use usleep_range where possible to reduce busy waits
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Noise floor calibration does not interfere with traffic and should run more
often as part of our "short calibration". The full calibration is not the
noise floor calibration but the AGC + Gain_F (on RF5111 and RF5112) calibration
and should run less often because it does interfere with traffic.

So

Short calibration -> I/Q & NF Calibration
Long calibration -> Short + AGC + Gain_F

This patch was for some time on my pub/ dir on www.kernel.org and has been tested
by a few people and me. I think it's O.K. to go in.

I also changed ah_calibration to ah_iq_cal_needed to make more sense.

v2 Use a workqueue instead of a tasklet for calibration
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No functional changes, just a few comments/documentation/cleanup
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add TXNOFRM to INT_TX_ALL since it's a TX interrupt too.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since card has 12 tx queues and we want to keep track of the interrupts
per queue we can't fit all these interrupt bits on a single register.
So we have 5 registers, the primary interrupt status register (PISR) and
the 4 secondary interupt status registers (SISRs).

In order to be able to read them all at once (atomic operation) Atheros
introduced the Read-And-Clear registers to make things easier. So when
reading RAC_PISR register, hw does a read on PISR and all SISRs, returns
the value of PISR, copies all SISR values to their shadow copies (RAC_SISRx)
and clears PISR and SISRs. This saves us from reading PISR/SISRs in a sequence.

So far we 've used this approach and MadWiFi/Windows driver etc also used it
for years.

It turns out this operation is not atomic after all (at least not on all cards)
That means it's possible to loose some interrupts because they came after the
copy step and hw cleared them on the clean step !

That's probably the reason we got missed beacons, got stuck queues etc and
couldn't figure out what was going on.

With this patch we switch from RaC operation to an alternative method (that
makes more sense IMHO anyway, I just chose to be on the safe side so far).
Instead of reading RAC registers, we read the normal PISR/SISR registers and
clear any bits we got by writing them back on the register. This will clear only
the bits we got on our read step and leave any new bits unaffected (at least
that's what docs say). So if any new interrupts come up we won't miss it.

I've tested this with an AR5213 and an AR2425 and it seems O.K.

Many thanks to Adrian Chadd for debuging this and reviewing the patch !

v2: Make sure we don't clear PISR bits that map to SISR generated interrupts
(added a comment on the code for this)
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The conformance test limits (CTL) for each regulatory domains
(FCC/ETSI/MKK) are programmed for each runtime modes (11B,11G,
HT20 and HT40) in EEPROM. The lowest ctledge power value of a
particular running mode should not be used while computing
ctledge power for a different running mode.(i.e 11G's min ctledge
power should not be used while computing ctledge power for HT20).

Currently, the code does not handle this properly which would
result in incorrect txpowers in certain cases. So reset the
twiceMaxEdgePower to the default while computing min ctlegepower
for every mode.

Cc: David Quan <dquan@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When tx agg is being stopped TID is flushed using ath_tx_flush_tid. It
is possible that ath_tx_flush_tid completelly flushes TID (if all
packets in this TID have already been retried). If this happened
ath_tx_aggr_stop would leave TID in cleanup state permanently.
Fix this by making ath_tx_flush_tid remove AGGR_ADDBA_COMPLETE and
AGGR_CLEANUP flags from TID status if TID is empty.
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the past, it was fine to simply call
dev_kfree_skb when it was impossible to
transmit a skb. However, with the new
tx status API:
"mac80211: implement wifi TX status"
Every loose skb needs to be handed back
to mac80211.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

DFS events are reported as PHY errors and need to be processed
with a correct timestamp set before ath9k_skb_preprocess() is
called and the frame is possibly dropped.

This patch puts the rxs->mactime calculation before the skb
is preprocessed to prepare for DFS event reporting.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove all wlan weight macros and group it together for better
understanding & readability. It makes the code reusable for
AR9462 wlan weights.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>