ath6kl/sdio.c:875: CHECK: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Recommended by checkpatch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

My patch 24fc32b3 ("ath6kl: add ath6kl_bmi_write_hi32()") caused a regression
in ath6kl_upload_board_file() and the board_address variable was not
properly initialised in some cases:

ath6kl/init.c:1068:6: warning: ‘board_address’ may be used uninitialized
in this function

Most likely this broke ar6004 support but I can't test that right now.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Portion of the commit id 080eec4f ("ath6kl: Clear the IE in firmware
if not set") was overwritten by mistake due to a merge
conflict. This patch fixes the code back to how it should be.

kvalo: more details to the commit log
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl_bmi_[read|write]_hi32() did not have endian support, fix that.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

drivers/net/wireless/ath/ath6kl/init.c:78: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/init.c:397: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/init.c:407: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:189: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:704: WARNING: line over 80 characters
drivers/net/wireless/ath/ath6kl/htc.c:2452: WARNING: line over 80 characters
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Also fixes quite a few checkpatch warnings like this:

ath6kl/hif.h:226: CHECK: spinlock_t definition without comment
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl/cfg80211.c:462: CHECK: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The error handling in ath6kl_target_config_wlan_params() was just weird,
fix that. This also fixes some of the open parenthesis alignment issues
reported by checkpatch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are few 32 bit reads from the host interest area. Add
ath6kl_bmi_read_hi32() to make it easier to do that. As code is cleaner
this also fixes few checkpatch warnings.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We have a lot of 32 bit writes to the host interest area and the code
doing that is ugly. Clean that up by adding ath6kl_bmi_write_hi32().

This also fixes few checkpatch warnings.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

drivers/net/wireless/ath/ath6kl/cfg80211.c:1295: CHECK: multiple assignments should be avoided
drivers/net/wireless/ath/ath6kl/cfg80211.c:3000: CHECK: multiple assignments should be avoided
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

All found by checkpatch:

ath6kl/wmi.c:1036: CHECK: Logical continuations should be on the previous line
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix the issues which checkpatch found and were easy to fix. Especially
callers of ath6kl_bmi_write() are tricky and that needs to be fixed
separately.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl/debug.c:739: ERROR: Macros with complex values should be
enclosed in parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

reported by checkpatch:

ath6kl/core.h:748: ERROR: "foo * bar" should be "foo *bar"
ath6kl/core.h:751: ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

* In order to save the target power in WOW suspend state,
  configure the best optimal values for the below parameters,
     - listen interval.
     - beacon miss interval.
     - scan parameters.

  Default values for above attributes are reverted in
  wow resume operation.

* The default listen interval is set before the host issue
  connect request.

* New function is added to configure beacon miss count.

kvalo: minor changes to fix open parenthesis alignment
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware has the option to support the listen interval
per vif specific. Fix this.

Listen interval can be set by the TUs or by the number
of beacons. Current code enables the user to configure
the listen interval in the unit of 'number of beacons'
using debugfs entry "listen_interval". Going forward,
we need to alter the listen interval in the unit of TUs
to get good power numbers while going to WOW suspend/resume.

Allowing the user to change the listen interval in
the unit of "number of beacons"  in debugfs and changing
listen interval in wow suspend/resume in the unit of
time (TUs) would lead us to confuse.

This patch make sures the listen interval is changed only
in the unit of time (TUs).
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Below two scenarios are taken care in this patch which helped
to fix the firmware crash during wow suspend/resume.

* TX operation (ctrl tx and data tx) has to be controlled based
  on suspend state. i.e, with respect to WOW mode, control packets
  are allowed to send from the host until the suspend state goes
  ATH6KL_STATE_WOW and the data packets are allowed until WOW
  suspend operation starts.

* Similarly, wow resume is NOT allowed if WOW suspend is in progress.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It gives flexibility to the user to define suspend policy
when the suspend mode is set to WOW and the device is in
disconnected state at the time of suspend.

New module parameter wow_mode is added to get the choice
from the user. This parameter is valid only if the module
parameter suspend_mode is set to WOW.

To force WOW in connected state and cut power
in disconnected state:
  suspend_mode=0x3 wow_mode=0x1

To force WOW in connected state and deep sleep
in disconnected state (this is also the default wow_mode):
   suspend_mode=0x3 wow_mode=0x2

If there is no value specified to wow_mode during insmod,
deep sleep mode will be tried in the disconnected state.

kvalo: clarified commit log
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

"ath6kl: Defer wiphy and netdev registration till the end of ath6kl_core_init()"
causes kernel panic by accessing the unallocated debug resources during
boot time. To fix this, split the debug initialization funtion into two,
one initializes the debug resource and the other takes care of debugfs
initialization. When this issue shows up the kernel crash dump would
look like

 ath6kl_debug_fwlog_event+0x9c/0x10a
 [<c10666c9>] register_lock_class+0x57/0x288
 [<c1065cd3>] ? trace_hardirqs_on+0xb/0xd
 [<f801f4c9>] ? ath6kl_debug_fwlog_event+0x9c/0x10a
 [<c1066a8a>] __lock_acquire+0x96/0xbe5
 [<c106007b>] ? alarmtimer_suspend+0x80/0x127
 [<c10258da>] ? vprintk+0x394/0x3b1
 [<f801f4c9>] ? ath6kl_debug_fwlog_event+0x9c/0x10a
 [<c10676b3>] lock_acquire+0xda/0xf9
 [<f801f4c9>] ? ath6kl_debug_fwlog_event+0x9c/0x10a
 [<c1532ce3>] _raw_spin_lock+0x28/0x58
 [<f801f4c9>] ? ath6kl_debug_fwlog_event+0x9c/0x10a
 [<f801f4c9>] ath6kl_debug_fwlog_event+0x9c/0x10a
 [<f80310a4>] ath6kl_wmi_control_rx+0x69d/0xb50 [ath6kl_core]
 [<f802d2e1>] ? ath6kl_rx+0x3c/0x839 [ath6kl_core]
 [<f802d35d>] ath6kl_rx+0xb8/0x839 [ath6kl_core]
 [<c104b81e>] ? local_clock+0x2d/0x4e
 [<c102a0af>] ? _local_bh_enable_ip+0x94/0x98
 [<f802bfc0>] ? ath6kl_alloc_amsdu_rxbuf+0xb7/0xb7
 [<f8023b28>] ath6kl_htc_rxmsg_pending_handler+0x891/0x988 [ath6kl_core]
 [<f802bf00>] ? ath6kl_refill_amsdu_rxbufs+0x89/0x92
 [<f802d2a5>] ? aggr_timeout+0xed/0xed [ath6kl_core]
 [<f802bfc0>] ? ath6kl_alloc_amsdu_rxbuf+0xb7/0xb7
 [<f802c420>] ? ath6kl_tx_complete+0x376/0x376 [ath6kl_core]
 [<f8020e92>] ath6kl_hif_intr_bh_handler+0xf7/0x33e
 [<c138ab00>] ? mmc_host_disable+0x15/0x3a
 [<f8123b5c>] ath6kl_sdio_irq_handler+0x3c/0x90 [ath6kl_sdio]
 [<c1392f56>] sdio_irq_thread+0xb6/0x29c
 [<c1392ea0>] ? sdio_claim_irq+0x1cb/0x1cb
 [<c103d4c0>] kthread+0x67/0x6c
 [<c103d459>] ? __init_kthread_worker+0x42/0x42
 [<c153903a>] kernel_thread_helper+0x6/0xd
 BUG: unable to handle kernel NULL pointer dereference at
EIP: [<f801f4d4>] ath6kl_debug_fwlog_event+0xa7/0x10a

kvalo: rename new function to ath6kl_debug_init_fs() and add a comment
why it's needed
Reported-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Conflicts:
	drivers/net/wireless/ath/ath6kl/cfg80211.c

No need to copy received local buffer content to bounce buffer
(DMA buffer) while performing sync READ operation from the chip.

It's applicable for only WRITE operation.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The commit "ath6kl: Use a mutex_lock to avoid
race in diabling and handling irq" introduces a
state where ath6kl_sdio_irq_handler() would be waiting
to claim the sdio function for receive indefinitely
when things happen in the following order.

ath6kl_sdio_irq_handler()
	- aquires mtx_irq
	- sdio_release_host()
					ath6kl_sdio_irq_disable()
						- sdio_claim_host()
						- sleep on mtx_irq
	ath6kl_hif_intr_bh_handler()
		- (indefinitely) wait for the sdio
		  function to be released to exclusively claim
		  it again for receive operation.

Fix this by replacing the mtx_irq with an atomic
variable and a wait_queue.

kvalo: add ath6kl_sdio_is_on_irq() due to open parenthesis alignment
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Collect residue firmware logs following firmware assert.
Firmware sends logs to host once the 1500 byte log buffer
has been filled. At time of assert, there could be residue
logs lying in the firmware. This patch pulls those residue
logs. This would give the full picture of the firmware.
Signed-off-by: NEtay Luz <eluz@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

firmware debug utility expects firmware log record size
to be 1500 bytes. This patch ensures that the
firmware record will be exactly 1500 bytes.

kvalo: remove trailing space
Signed-off-by: NEtay Luz <eluz@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The ath6kl FW does not distinguish between different types of hidden
SSIDs (empty or null), so treat all cfg80211 requests for hidden ssid
the same.
Signed-off-by: NThomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Remove check so that IE in firmware is cleared if not set. Without this fix, any
previously set IE will be used incorrectly in the next frame. For example,
consider the scenario where a P2P device scan is followed by a regular station
scan. The P2P IE set by the P2P scan needs to be cleared, otherwise the station
scan will contain the P2P IE.

kvalo: indentation fixes
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As regulatory events are processed even before the wiphy is registered,
calling regulatory_hint() at early stage should be fixed.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes the wiphy and initial netdev registration the last step
in dev initialization. Apart from the fact that this looks right,
it can also be used to setup wiphy with the regulatory information
received from firmware after uploading the firmware. Also it fixes
a FIXME in ath6kl_core_init() where mac address is copied into
netdev->dev_addr, ath6kl_interface_add() takes care of this as well.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When the wmi event is vif specific, the validation of vif index
is taken care in ath6kl_wmi_proc_events_iface(). This also avoids
the need for a netdev to be registered while receiving initial events
like "target_ready" and "regulatory domain".
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Split the wmi event processing into the one which needs to be
vif specific and the reset. This is a step towards avoiding
the need for wiphy and a netdev registration before getting
any message from firmware.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Move netdev->hw_features setting from ath6kl_core_init() to
init_netdev() so that it is done for every interface.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are some code which initializes various wiphy members
left outside ath6kl_cfg80211_init(), in ath6kl_core_init().
Move them into a single palce.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

That commit intended for 3.4 renamed IEEE80211_TX_CTL_POLL_RESPONSE as
IEEE80211_TX_CTL_NO_PS_BUFFER.  Meanwhile, "carl9170: fix frame delivery
if sta is in powersave mode" added a reference to
IEEE80211_TX_CTL_POLL_RESPONSE in the fixes stream for 3.3.  This simple
patch fixes that merge boo-boo.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previous RX error checking was done exclusive-or for different error
types and caused DFS pulse events to be dropped when other error
flags (e.g. CRC) were set simultaneously.

This patch decouples PHY error processing from other types and ensures
that all pulses detected by HW are accounted by the pattern detector.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the enum il4965_calib_enabled_state because it is not used.
Signed-off-by: NGreg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the enum il_calib. It defined one identifier: IL_CALIB_MAX.
Remove the function il4965_calib_free_results. It was doing nothing
because IL_CALIB_MAX is zero. Next, remove calib_results from the
il_priv structure and also remove the associated return
type/struct il_calib_result.
Signed-off-by: NGreg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the menuconfig system doesn't indent the debug options
for the 3945 /4965, add some text to make it clear which
debug options are being configured.
Signed-off-by: NGreg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>