Just as the function ipu_dmfc_config_wait4eot() tells, the DMFC wait4eot bit
depends on the number of DMFC slots to be used, so it should be called after
the slots are determined in the function ipu_dmfc_alloc_bandwidth().
Based on tests, this patch may eliminate display distortion issue on overlay
plane with small resolutions.  To reproduce the issue, we may run this drm
modetest case - 'modetest -P 19:64x64'.
Signed-off-by: NLiu Ying <gnuiyl@gmail.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

The function name 'ipu_dmfc_config_wait4eot' matches the implementation of
the function better than 'ipu_dmfc_init_channel', since it only touches the
wait4eot bits.
Signed-off-by: NLiu Ying <gnuiyl@gmail.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

Since the function ipu_dmfc_init_channel() always returns zero, we may
change the return type to void to simplify the code.
Signed-off-by: NLiu Ying <gnuiyl@gmail.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

The driver already advertises multi-planar YUV support, but
previously the U/V offset and stride setup was missing.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

The IPU addresses multiplanar formats using a base address and relative
offsets for the secondary planes. Since those offsets must be positive
and not too large, and none of the plane parameters except the base address
may be changed while scanout is active, store the pitches and u/v offsets
and check all values against IDMAC limitations.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

This patch changes the dev_info() call to dev_dbg() in ipu_plane_update()
to print out the information that a plane's CRTC is changed, because this
kind of information is only useful for debugging.
Signed-off-by: NLiu Ying <Ying.Liu@freescale.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

DRM_FORMAT_RGB565 is missing from ipu_plane_formats.
The support is there, just need to make it available to userspace.
Signed-off-by: NEnrico Jorns <ejo@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

Done with coccinelle for the most part. It choked on
msm/mdp/mdp5/mdp5_plane.c like so:
"BAD:!!!!!  enum drm_plane_type type;"
No idea how to deal with that, so I just fixed that up
by hand.

Also it thinks '...' is part of the semantic patch, so I put an
'int DOTDOTDOT' placeholder in its place and got rid of it with
sed afterwards.

I didn't convert drm_plane_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.

@@
typedef uint32_t;
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
 int drm_universal_plane_init(struct drm_device *dev,
                              struct drm_plane *plane,
                              unsigned long possible_crtcs,
                              const struct drm_plane_funcs *funcs,
                              const uint32_t *formats,
                              unsigned int format_count,
                              enum drm_plane_type type
+                             ,const char *name, int DOTDOTDOT
                              )
{ ... }

@@
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
 int drm_universal_plane_init(struct drm_device *dev,
                              struct drm_plane *plane,
                              unsigned long possible_crtcs,
                              const struct drm_plane_funcs *funcs,
                              const uint32_t *formats,
                              unsigned int format_count,
                              enum drm_plane_type type
+                             ,const char *name, int DOTDOTDOT
                              );

@@
expression E1, E2, E3, E4, E5, E6, E7;
@@
 drm_universal_plane_init(E1, E2, E3, E4, E5, E6, E7
+                         ,NULL
                          )

v2: Split crtc and plane changes apart
    Pass NUL for no-name instead of ""
    Leave drm_plane_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
    Annotate the function with __printf() attribute (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670795-2853-1-git-send-email-ville.syrjala@linux.intel.com

Use drm_universal_plane_init to create the planes, create the primary
plane first and use drm_crtc_init_with_planes to associate it with
the crtc.
This gets rid of the unused fallback primary plane previously created
by drm_crtc_init and fixes a NULL pointer dereference issue that can
be triggered by a modeset from userspace when fbdev helpers are
enabled [1].

[1] https://lkml.org/lkml/2015/11/4/107Reported-by: NLiu Ying <Ying.Liu@freescale.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NLiu Ying <Ying.Liu@freescale.com>

This patch allows to use the ARGB4444 color format on planes.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

This patch allows to use the RGBX and RGBA 8:8:8:8 formats.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

This patch enables the ARGB1555, ABGR1555, RGBA5551,
and BGRA5551 formats to be used on planes.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

This patch allows interlaced frame buffer scanout for interlaced output
via HDMI or TV-Encoder.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

The imx-drm driver was put into staging mostly for the following reasons,
all of which have been addressed or superseded:
 - convert the irq driver to use linear irq domains
 - work out the device tree bindings, this lead to the common of_graph
   bindings being used
 - factor out common helper functions, this mostly resulted in the
   component framework and drm of_graph helpers.

Before adding new fixes, and certainly before adding new features,
move it into its proper place below drivers/gpu/drm.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

While the DMA channel is running, it is not allowed to change anything
but the inactive (double) buffer base address, so resizing a plane or
changing to a frame buffer with different pixel format is not possible.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This allows to update the buffer base address while the DMA
channel is running. It is needed to flip the frame buffer of
an active plane.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Setting the stride can only be done on inactive channels, while
the buffer base address can also be updated for running channels
using the hardware double buffering feature.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For the overlay plane scanning out a framebuffer with an alpha component,
enable the DP local alpha feature on the partial plane.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All those ipu_*_put() calls in ipu_plane_dpms() are unnecessary,
because the only occurrence of ipu_plane_dpms() with 'mode' not being
DRM_MODE_DPMS_ON is in function ipu_disable_plane(), which already
has a ipu_plane_put_resources() call to put those ipu resources right
after ipu_plane_dpms().

So with those redundant ipu_*_put() calls removed from ipu_plane_dpms(),
the only left code in the function is ipu_plane_enable|disable().  Thus,
we can just call ipu_plane_enable|disable() as needed directly and
remove the ipu_plane_dpms() function completely.
Suggested-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When unbinding imx-drm, the following oops was observed:

Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = e995c000
[00000004] *pgd=4fea5831
Internal error: Oops: 817 [#1] SMP ARM
Modules linked in: bnep rfcomm bluetooth nfsd exportfs hid_cypress brcmfmac brcmutil snd_soc_fsl_ssi snd_soc_fsl_spdif imx_pcm_fiq imx_pcm_dma snd_soc_sgtl5000 imx_sdma imx2_wdt imx_ldb(C) imx_thermal snd_soc_imx_sgtl5000 snd_soc_imx_spdif snd_soc_imx_audmux
CPU: 1 PID: 779 Comm: bash Tainted: G         C    3.16.0-rc2+ #1230
task: ea9eb180 ti: ea378000 task.ti: ea378000
PC is at ipu_dp_put+0x10/0x18
LR is at ipu_plane_dpms+0x60/0x8c
pc : [<c0350d20>]    lr : [<c04bd9e8>]    psr: 200f0013
sp : ea379d80  ip : ea379d90  fp : ea379d8c
r10: 00100100  r9 : 00000000  r8 : 00200200
r7 : e9ba0264  r6 : e9ba01f8  r5 : 00000000  r4 : ea34b800
r3 : 00000000  r2 : 00000000  r1 : 0000009b  r0 : 00000000
Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c53c7d  Table: 3995c04a  DAC: 00000015
Process bash (pid: 779, stack limit = 0xea378240)
Stack: (0xea379d80 to 0xea37a000)
...
Backtrace:
[<c0350d10>] (ipu_dp_put) from [<c04bd9e8>] (ipu_plane_dpms+0x60/0x8c)
[<c04bd988>] (ipu_plane_dpms) from [<c04bda40>] (ipu_disable_plane+0x2c/0x60)
[<c04bda14>] (ipu_disable_plane) from [<c04bda9c>] (ipu_plane_destroy+0x28/0x60)
[<c04bda74>] (ipu_plane_destroy) from [<c033ff84>] (drm_mode_config_cleanup+0x1b8/0x250)
[<c033fdcc>] (drm_mode_config_cleanup) from [<c04bc234>] (imx_drm_driver_unload+0x44/0x4c)
[<c04bc1f0>] (imx_drm_driver_unload) from [<c03394a4>] (drm_dev_unregister+0x2c/0xa0)
[<c0339478>] (drm_dev_unregister) from [<c0339f8c>] (drm_put_dev+0x30/0x6c)
[<c0339f5c>] (drm_put_dev) from [<c04bc1cc>] (imx_drm_unbind+0x14/0x18)
[<c04bc1b8>] (imx_drm_unbind) from [<c03530b4>] (component_master_del+0xbc/0xd8)
...
Code: e1a0c00d e92dd800 e24cb004 e3a03000 (e5c03004)

This is caused by a missing check in ipu_plane_dpms for a NULL pointer.

Fixes: b8d181e4 ("staging: drm/imx: add drm plane support")
Cc: <stable@vger.kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ipu_cpmem_*() calls now take a channel pointer instead of a
pointer into cpmem for that channel.
Signed-off-by: NSteve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>

The i.MX Image Processing Unit (IPU) contains a number of image processing
blocks that sit right in the middle between DRM and V4L2. Some of the modules,
such as Display Controller, Processor, and Interface (DC, DP, DI) or CMOS
Sensor Interface (CSI) and their FIFOs could be assigned to either framework,
but others, such as the dma controller (IDMAC) and image converter (IC) can
be used by both.
The IPUv3 core driver provides an internal API to access the modules, to be
used by both DRM and V4L2 IPUv3 drivers.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The former has to be done before disabling the DMFC, the latter has to be
done afterwards. Otherwise the DMFC FIFOs never get cleared properly.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are only a few users of the DRM_LOG_KMS() macro. We can simplify
the DRM code a bit by replacing them by DRM_DEBUG_KMS().

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix the following static checker warning:

drivers/staging/imx-drm/ipuv3-plane.c:75:2: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t' [-Wformat]

Use %pad to print 'dma_addr_t'.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CRTC offsets are only set with the initial modeset, any
subseqent pageflips assume them to be kept the same, so
we need to remember the current state until another modeset
changes it.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We didn't take the pixel format into account, so x-direction
offsets were off by a factor of 2 or 4 for 16bpp and 32bpp
framebuffers.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Even though we do not enable the hardware double buffering feature
right now, set the second base address pointer (EBA1) as well to
increase robustness.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for a drm overlay plane on DI0 using the DP.
In principle, the overlay plane could also be used on DI1, but to switch
the overlay plane between display interfaces, the base planes would have
to be exchanged transparently while both display interfaces are inactive.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>