Otherwise, cross compilation may fail with error messages like:

...
size: arch/arm/boot/compressed/../../../../vmlinux: File format is ambiguous
size: Matching formats: elf32-littlearm elf32-littlearm-symbian elf32-littlearm-vxworks
  LD      arch/arm/boot/compressed/vmlinux
  arm-angstrom-linux-uclibcgnueabi-ld:--defsym _kernel_bss_size=: syntax error
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add initial dts file for EXYNOS4210 SoC. This dts file describes
the SoC specific devices and properties. Along with this, add dts
file for Samsung's SMDKV310 board and Insignal's ORIGEN board which
uses the EXYNOS4210 dts file and extends it to describe the board
specific properties.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This brings all the GPIO key definitions from board-seaboard.c into
tegra-seaboard.dtsi.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The ADT7461 is a temperature monitoring IC. One is present on the DVC
I2C bus on Seaboard.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Update the device tree to indicate which I2C controller is the DVC
controller. AUXDATA needs to be updated too, since the compatible
value changed.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add support for the tegra30 based cardhu development board. Cardhu is a tablet
formfactor reference design for tegra30. The patch provides a device tree for
the board, updates Makefile.boot to build the dtb, includes the platform in
Kconfig and updates board-dt.c.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds the initial device tree for tegra30
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add some runtime test cases for the library of device tree parsing functions.

v2: - Add testcase for phandle with 0 args
    - Don't run testcases if testcase data isn't present in device tree
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Before we enable the MMU, we must ensure that the TTBR registers contain
sane values. After the MMU has been enabled, we jump to the *virtual*
address of the following function, so we also need to ensure that the
SCTLR write has taken effect.

This patch adds ISB instructions around the SCTLR write to ensure the
visibility of the above.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Convert tegra20 IRQ intialization to the GIC devicetree binding. Modify the
interrupt definitions in the dts files according to
Documentation/devicetree/bindings/arm/gic.txt

v3 (swarren):
* Moved of_irq_init() call into board-dt.c to avoid ifdef'ing it.
  - Even with a dummy replacement if !CONFIG_OF, the reference from
    tegra_dt_irq_match[] to gic_of_init() would still have to be ifdef'd
  - It's plausible that tegra_dt_irq_match[] may need to contain more
    entries in the future, and defining what they are seems more suitable
    for board-dt.c than irq.c
v2 (swarren):
* Removed some stale GIC init code from board-dt.c
* Undid some accidental 0x -> 0x0 search/replace.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
[olof: added include of <asm/hardware/gic.h> for compile to pass]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Mark any SDHCI controllers that aren't registered by the board files as
disabled in the device-tree files.

In practice, these controllers:

* Have nothing hooked up to them at all, or
* For ports intended for SDIO usage, the drivers for anything that might
  be attached are not in the device-tree yet. If/when drivers appear, the
  SD/MMC port can be re-enabled.

The only possible exception is TrimSlice's mico SD slot, but that wasn't
enabled in the board files before anyway, and doesn't work when all the
SDHCI controllers are enabled anyway.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Mark any serial ports that aren't registered by the board files as disabled
in the device-tree files.

In practice, none of the now-disabled ports ended up succeeding device
probing because of the missing clock-frequency property. However,
explicitly marking the devices disabled has the advantage of squashing
the dev_warn() the failed probe causes, and documenting that we intend
the port not to be used, rather than accidentally left out the property.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

With board files, all I2C busses run at 400KHz. Fix the device-tree
to be consistent with this. It's possible this is incorrect, but at
least it keeps the board files and device-tree consistent.

Also, disable any I2C controllers that the board files don't register,
also for consistency.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The command-lines present in the existing /chosen node are not necessarily
correct for all users. Ideally, we should simply use the command-line
supplied by the boot-loader.

In fact, using the boot-loader's cmdline is quite easy; either the
bootloader fully supports DT, in which case it can modify the DT passed
to the kernel to include its command-line, or CONFIG_APPENDED_DTB can
be used in conjunction with CONFIG_ARM_ATAG_DTB_COMPAT, and the kernel
will substitute the bootloader's command-line into the DT.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

There are no drivers in the kernel at present which can make use of the
memory reserved by /memreserve/, so there is no point reserving it. Remove
/memreserve/ to allow the user more memory. It's also unclear whether any
future driver would actually require /memreserve/, or allocate memory
through some other mechanism.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This adds a dts file for paz00. As a side effect, this also enables
the embedded controller which controls the keyboard, touchpad, power,
leds, and some other functions.

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NMarc Dietrich <marvin24@gmx.de>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

* Add device-tree file for TrimSlice
* Add that to the list of .dts files to build
* Update board-dt.c to recognize TrimSlice board name

v2: Makefile: Add board-trimslice-pinmux.c to obj-$(CONFIG_MACH_TEGRA_DT).
v3: Makefile: Use brackets not braces around var names
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The I2S and DAS nodes don't have children, and hence don't need to set
address/size cells.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

For now they are a minimal binding. It needs to be amended with
vendor-specific settings for phy setup and link tuning, etc.

v2: Added bindings specification and phy_type properties
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NStephen Warren <swarren@nvidia.com>

Ventana uses the same SDHCI GPIOs as Seaboard; PI6 (70) is the power GPIO
for the SD port, and there is no power GPIO for the MMC chip.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The patch 'arm/dt: Add dtb make rule' adds support to
create a .dtb file. But this is never removed afterwards.
Remove the generated .dtb file if 'distclean' is called.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Jason Liu <jason.hui@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It adds device tree source and documentation for imx6q platform.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This adds the devicetree source and documentation for the Calxeda highbank
platform.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Reviewed-by: NJamie Iles <jamie@jamieiles.com>
Reviewed-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>

Create a new device tree source file for Atmel at91sam9g45 SoC family.
The Evaluation Kit at91sam9m10g45ek includes it.
This first basic support will be populated as drivers and boards will be
converted to device tree.
Contains serial, dma and interrupt controllers.

The generic board file still takes advantage of platform data for early serial
init. As we need a storage media and the NAND flash driver is not converted to
DT yet, we keep old initialization for it.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>

If TEXT_OFFSET is too large (e.g. like on MSM) the resulting immediate
argument gets wider than 8 bits.

Noticed by David Brown <davidb@codeaurora.org>
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Cc: Rob Herring <robherring2@gmail.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>

It adds device tree support for imx51 babbage board.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

It adds device tree support for imx53 boards.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Get rid of this complaint from dash:

    AS      arch/arm/boot/compressed/lib1funcs.o
  /bin/sh: 1: [: y: unexpected operator
    LD      arch/arm/boot/compressed/vmlinux
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

uImages need a load address specified. This makes them
incompatible with multiple zreladdrs. Catch this error
before building an uImage so that we do not end up with
broken uImages. The load address can still be specified
with LOADADDR= on the command line.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Without CONFIG_AUTO_ZRELADDR being set the kernel needs a single
zreladdr for building zImages. Bail out if we detect multiple
zreladdrs without CONFIG_AUTO_ZRELADDR.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add a pinmux node to tegra20.dtsi in order to instantiate the future
pinmux device.

v2: Specify reg property precisely; don't just point at the whole APB_MISC
register range.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add nodes for devices used by PM code (mpu, dsp, iva).

Add a cpus node as well as recommended in the DT spec.

Remove mpu, dsp, iva devices init if is populated.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>

Used the main OCP node to add bindings with the l3_noc driver.
Remove l3_noc static device creation if DT is populated.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>

Add OMAP3 beagleboard DTS file to use the omap3.dtsi SoC file.

Add a default bootargs line to allow a boot from RAMDISK.

Add memory node information.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Add initial OMAP3 soc file with empty ocp bus.

Based on initial patch from Manju:
http://www.spinics.net/lists/linux-omap/msg55830.htmlSigned-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Add the SDP/Blaze (Software Development Board) support with
device tree.
That file is based on the omap4-panda.dts.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Based on the original omap4-panda.dts file from Manju.
http://www.spinics.net/lists/linux-omap/msg55836.html

Add memory information and a default bootargs to allow
a boot from RAMDISK.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>