When enabling the sub-CRQ IRQ a previous update sent a H_EOI prior
to the enablement to clear any pending interrupts that may be present
across a partition migration. This fixed a firmware bug where a
migration could erroneously indicate that a H_EOI was pending.

The H_EOI should only be sent when enabling during a mobility
event though. Doing so at other time could wrong and can produce
extra driver output when IRQs are enabled when doing TX completion.
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When link is down, writes to the device might fail with
-EIO. Userspace needs an indication when the status is resolved.  As a
fix, tun_net_open() attempts to wake up writers - but that is only
effective if SOCKWQ_ASYNC_NOSPACE has been set in the past. This is
not the case of vhost_net which only poll for EPOLLOUT after it meets
errors during sendmsg().

This patch fixes this by making sure SOCKWQ_ASYNC_NOSPACE is set when
socket is not writable or device is down to guarantee EPOLLOUT will be
raised in either tun_chr_poll() or tun_sock_write_space() after device
is up.

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 1bd4978a ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to drop refcnt to xdp_page if we see a gso packet. Otherwise
it will be leaked. Fixing this by moving the check of gso packet above
the linearizing logic. While at it, remove useless comment as well.

Cc: John Fastabend <john.fastabend@gmail.com>
Fixes: 72979a6c ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we successfully linearize the packet, num_buf will be set to zero
which may confuse error handling path which assumes num_buf is at
least 1 and this can lead the code tries to pop the descriptor of next
buffer. Fixing this by checking num_buf against 1 before decreasing.

Fixes: 4941d472 ("virtio-net: do not reset during XDP set")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should not go for the error path after successfully transmitting a
XDP buffer after linearizing. Since the error path may try to pop and
drop next packet and increase the drop counters. Fixing this by simply
drop the refcnt of original page and go for xmit path.

Fixes: 72979a6c ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After a linearized packet was redirected by XDP, we should not go for
the err path which will try to pop buffers for the next packet and
increase the drop counter. Fixing this by just drop the page refcnt
for the original page.

Fixes: 186b3c99 ("virtio-net: support XDP_REDIRECT")
Reported-by: NDavid Ahern <dsahern@gmail.com>
Tested-by: NDavid Ahern <dsahern@gmail.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure to invoke pci_disable_device() when errors occur in
pcnet32_probe_pci().
Signed-off-by: NBo Chen <chenbo@pdx.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.

Fix that mask to handle 64bit physical address.

Fixes: fe56b9e6 ("qed: Add module with basic common support")
Signed-off-by: NShahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there is no license information in the header of
this file.

The MODULE_LICENSE field contains ("GPL"), which means
GNU Public License v2 or later, so add a corresponding
SPDX license identifier.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since 6335698e the radio with idx of 0
will not get dumped in HWSIM_CMD_GET_RADIO because of the last_idx
checks.  Offset cb->args[0] by 1 similarly to what is done in nl80211.c.

Fixes: 6335698e ("mac80211_hwsim: add generation count for netlink dump operation")
Signed-off-by: NAndrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Correct the indirect register offsets in collecting TX rate limit info
in UP CIM logs.

Also, T5 doesn't support these indirect register offsets, so remove
them from collection logic.

Fixes: be6e36d9 ("cxgb4: collect TX rate limit info in UP CIM logs")
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 9b5ba0df ("ARM: shmobile: Introduce ARCH_RENESAS")
is CONFIG_ARCH_RENESAS a more appropriate platform check than the legacy
CONFIG_ARCH_SHMOBILE, hence use the former.

Renesas SuperH SH-Mobile SoCs are still covered by the CONFIG_CPU_SH4
check.

This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move initialization of statistics buffers from ibmvnic_init function
into ibmvnic_probe. In the current state, ibmvnic_init will be called
again during a device reset, resulting in the allocation of new
buffers without freeing the old ones.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not necessary to disable interrupt lines here during a reset
to handle a non-fatal firmware error. Move that call within the code
block that handles the other cases that do require interrupts to be
disabled and re-enabled.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the firmware map fails for whatever reason, remember to free
up the memory after.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit b196d88a ("tun: fix use after free for ptr_ring") we
need clean up tx ring during release(). But unfortunately, it tries to
do the cleanup blindly after socket were destroyed which will lead
another use-after-free. Fix this by doing the cleanup before dropping
the last reference of the socket in __tun_detach().
Reported-by: NAndrei Vagin <avagin@virtuozzo.com>
Acked-by: NAndrei Vagin <avagin@virtuozzo.com>
Fixes: b196d88a ("tun: fix use after free for ptr_ring")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stress on qedi/qedr load unload lead to list_del corruption.
This is due to ll2 connection terminate freeing resources without
verifying that no more ll2 processing will occur.

This patch unregisters the ll2 status block before terminating
the connection to assure this race does not occur.

Fixes: 1d6cff4f ("qed: Add iSCSI out of order packet handling")
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ll2 flows of flushing the txq/rxq need to be synchronized with the
regular fp processing. Caused list corruption during load/unload stress
tests.

Fixes: 0a7fb11c ("qed: Add Light L2 support")
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver should free all pending isles once it gets a FLUSH cqe from FW.
Part of iSCSI out of order flow.

Fixes: 1d6cff4f ("qed: Add iSCSI out of order packet handling")
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The configuration settings for RBTX4927 were accidentally removed,
leading to a silently broken network interface.

Re-add the missing settings to fix this.

Fixes: 8eb97ff5 ("net: 8390: remove m32r specific bits")
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was possible to delete only one half of an IPv6, which would leave
the second half still programmed and possibly in use. Instead of
checking for the unused bitmap, we need to check the unique bitmap, and
refuse any deletion that does not match that criteria. We also need to
move that check from bcm_sf2_cfp_rule_del_one() into its caller:
bcm_sf2_cfp_rule_del() otherwise we would not be able to delete second
halves anymore that would not pass the first test.

Fixes: ba0696c2 ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We had several issues that would make the programming of IPv6 rules both
inconsistent and error prone:

- the chain ID that we would be asking the hardware to put in the
  packet's Broadcom tag would be off by one, it would return one of the
  two indexes, but not the one user-space specified

- when an user specified a particular location to insert a CFP rule at,
  we would not be returning the same index, which would be confusing if
  nothing else

- finally, like IPv4, it would be possible to overflow the last entry by
  re-programming it

Fix this by swapping the usage of rule_index[0] and rule_index[1] where
relevant in order to return a consistent and correct user-space
experience.

Fixes: ba0696c2 ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we let the kernel pick up a rule location with RX_CLS_LOC_ANY, we
would be able to overwrite the last rules because of a number of issues.

The IPv4 code path would not be checking that rule_index is within
bounds, and it would also only be allowed to pick up rules from range
0..126 instead of the full 0..127 range. This would lead us to allow
overwriting the last rule when we let the kernel pick-up the location.

Fixes: 33061458 ("net: dsa: bcm_sf2: Move IPv4 CFP processing to specific functions")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.

The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.

Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.
Signed-off-by: NMarkus Niebel <Markus.Niebel@tqs.de>
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: NMarco Felsch <m.felsch@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When master device's mac has been changed, the commit
32c10bbf ("ipvlan: always use the current L2 addr of the
master") makes the IPVlan devices's mac changed also, but it
doesn't do related works such as flush the IPVlan devices's
arp table.
Signed-off-by: NKeefe Liu <liuqifa@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The gen bits must be read first from (resp. written last to) DMA memory.
The proper way to enforce this on Linux is to call dma_rmb() (resp.
dma_wmb()).
Signed-off-by: NRegis Duchesne <hpreg@vmware.com>
Acked-by: NRonak Doshi <doshir@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DMA mask must be set before, not after, the first DMA map operation, or
the first DMA map operation could in theory fail on some systems.

Fixes: b0eb57cb ("VMXNET3: Add support for virtual IOMMU")
Signed-off-by: NRegis Duchesne <hpreg@vmware.com>
Acked-by: NRonak Doshi <doshir@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Earlier code of doing bitwise AND with field width bits was wrong.
Instead, simplify code to calculate ntuple_mask based on supplied
fields and then compare with mask configured in hw - which is the
correct and simpler way to validate ntuple mask.

Fixes: 3eb8b62d ("cxgb4: add support to create hash-filters via tc-flower offload")
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid exiting the function with a lingering sysfs file (if the first
call to device_create_file() fails while the second succeeds), and avoid
calling devlink_port_unregister() twice.

In other words, either mlx4_init_port_info() succeeds and returns zero, or
it fails, returns non-zero, and requires no cleanup.

Fixes: 096335b3 ("mlx4_core: Allow dynamic MTU configuration for IB ports")
Signed-off-by: NTarick Bedeir <tarick@google.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to initialize ptr_ring during TUNSETIFF, this is because its
size depends on the tx_queue_len of netdevice. And we try to clean it
up when socket were detached from netdevice. A race were spotted when
trying to do uninit during a read which will lead a use after free for
pointer ring. Solving this by always initialize a zero size ptr_ring
in open() and do resizing during TUNSETIFF, and then we can safely do
cleanup during close(). With this, there's no need for the workaround
that was introduced by commit 4df0bfc7 ("tun: fix a memory leak
for tfile->tx_array").

Reported-by: syzbot+e8b902c3c3fadf0a9dba@syzkaller.appspotmail.com
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Fixes: 1576d986 ("tun: switch to use skb array for tx")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rebooting while qedr is loaded with a VLAN interface present
results in unregister_netdevice waiting for the usage count
to become free.
The fix is that rdma devices should be removed before unregistering
the netdevice, to assure all references to ndev are decreased.

Fixes: cee9fbd8 ("qede: Add qedr framework")
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NMichal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver supports EISA devices in addition to PCI devices, and relied
on the legacy behavior of the pci_dma* shims to pass on a NULL pointer
to the DMA API, and the DMA API being able to handle that.  When the
NULL forwarding broke the EISA support got broken.  Fix this by converting
to the DMA API instead of the legacy PCI shims.

Fixes: 4167b2ad ("PCI: Remove NULL device handling from PCI DMA API")
Reported-by: Ntedheadster <tedheadster@gmail.com>
Tested-by: Ntedheadster <tedheadster@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error clean up path kfree's adapter->ipsec and should be
instead kfree'ing ipsec. Fix this.  Also, the err1 error exit path
does not need to kfree ipsec because this failure path was for
the failed allocation of ipsec.

Detected by CoverityScan, CID#146424 ("Resource Leak")

Fixes: 63a67fe2 ("ixgbe: add ipsec offload add and remove SA")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: NLuc Van Oostenryck <luc.vanoostenryck@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add check for unsupported module and return the error code.
This fixes a Coverity hit due to unused return status from setup_sfp.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Prior to this commit, the rq_last_status was only set when hardware
responded with an error. This leads to rq_last_status being invalid
in the future when hardware eventually responds without error. This
commit resolves the issue by unconditionally setting rq_last_status
with the value returned in the descriptor.

Fixes: 940b61af ("ice: Initialize PF and setup miscellaneous
interrupt")
Signed-off-by: NJeff Shaw <jeffrey.b.shaw@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Resources are not freed in the reverse order of the allocation.
Labels are also mixed-up.

Fix it and reorder code and labels in the error handling path of
'mlxsw_core_bus_device_register()'

Fixes: ef3116e5 ("mlxsw: spectrum: Register KVD resources with devlink")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was a regression at some point from the intended functionality of
commit f60c3704 ("bonding: Fix alb mode to only use first level
vlans.")

Given the return value vlan_get_encap_level() we need to store the nest
level of the bond device, and then compare the vlan's encap level to
this. Without this, this check always fails and learning packets are
never sent.

In addition, this same commit caused a regression in the behavior of
balance_alb, which requires learning packets be sent for all interfaces
using the slave's mac in order to load balance properly. For vlan's
that have not set a user mac, we can send after checking one bit.
Otherwise we need send the set mac, albeit defeating rx load balancing
for that vlan.
Signed-off-by: NDebabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure multicast, broadcast, and zero mac's cannot be the output of rlb
updates, which should all be directed arps. Receive load balancing will be
collapsed if any of these happen, as the switch will broadcast.
Signed-off-by: NDebabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>