The local APIC is no longer forced off when "nosmp" has been specified.
Correct the message printed.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Disable the 8259A acting in the "virtual wire" mode to keep the interrupt
line inactive while fiddling with local APIC interrupt vector registers
associated with its destination inputs.  To be on the safe side,
especially concerning flipping the trigger mode.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Disable the 8259A when routing of the timer interrupt through the chip to
the local APIC of the primary processor has failed.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Remove the "disable_8254_timer" and "enable_8254_timer" kernel
parameters.  Now that AEOI acknowledgements are no longer needed for
correct timer operation, the 8259A can be kept disabled unconditionally
unless interrupts, either timer or watchdog ones, are actually passed
through it.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The code that used to be in do_slow_gettimeoffset() that relied on the
IRR bit of the master 8259A PIC for IRQ0 to check the state of the output
timer 0 of the PIT is no longer there.  As a result, there is no need to
use the POLL command to acknowledge the timer interrupt in the "8259A
Virtual Wire", except for the NMI watchdog when the i82489DX APIC is used
(this is because this particular APIC treats NMIs as level-triggered and
keeping the input asserted would keep motherboard NMI sources held off for
too long).  Remove the unneeded bits and adjust comments accordingly.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This reverts commit 0b6a39f7.

The changes in tip/x86/apic solve this better.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Since the trampoline code is now used for ACPI resume from suspend to RAM,
the trampoline page tables have to be fixed up during boot not only on SMP
systems, but also on UP systems that use the trampoline.

Reference: http://bugzilla.kernel.org/show_bug.cgi?id=10923Reported-by: NDionisus Torimens <djtm@gmx.net>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Some Dell laptops enter resume with apparent garbage in the segment
descriptor registers (almost certainly the result of a botched
transition from protected to real mode.)  The only way to clean that
up is to enter protected mode ourselves and clean out the descriptor
registers.

This fixes resume on Dell XPS M1210 and Dell D620.

Reference: http://bugzilla.kernel.org/show_bug.cgi?id=10927Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Tested-by: NKirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The build of the Alpha Linux kernel currently fails[1] with inconsistent
kallsyms data.  As I never saw that before, I thought about hardware
problems.  But in fact it is a bug in the Linux kernel.

The end of the rodata section is marked with the "__end_rodata" symbol.
This symbol have different aligning constraints than the inittext parts
and therefor the start marked "_sinittext".  Because of that the
__end_rodata symbol shifts between < _sinittext and == _sinittext.  The
later variant is seen as a code symbol and recorded in the kallsyms data.

On fix would be to move the exception table a little bit and get some
space between that two areas.

[1]: http://buildd.debian.org/fetch.cgi?pkg=linux-2.6&arch=alpha&ver=2.6.25-5&stamp=1213919009&file=log&as=raw

Cc: maximilian attems <max@stro.at>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide __ucmpdi2() for MN10300 so that allmodconfig can be built.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Export kernel_thread() and empty_zero_page so that allmodconfig can be
built for MN10300.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When converting the page number in a pte/pmd/pud/pgd between
machine and pseudo-physical addresses, the converted result was
being truncated at 32-bits.  This caused failures on machines
with more than 4G of physical memory.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: "Christopher S. Aker" <caker@theshore.net>
Cc: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The txx9_tmr_init() will not clear a timer counter register in a certain
case.  The counter register is cleared on 1->0 transition of TCE bit if
CRE=1.  So just clearing the TCE bit is not enough.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The introduction of a real dma cache invalidate makes it important
to have a correct cache line size, otherwise the kernel will gives
out two memory segment, which might share one cache line. The R4400
Indy/Indigo2 CPU modules are using a second level cache line size
of 128 bytes, so MIPS_L1_CACHE_SHIFT needs to be bumped up to 7 for
IP22.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It's possible that the crime interrupt handler is called without
pending interrupts (probably a hardware issue). To avoid irritating
"unexpected irq 71" messages, we now just ignore the spurious crime
interrupts.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

fix this warning:

arch/x86/mm/init_64.c: In function 'early_memtest':
arch/x86/mm/init_64.c:524: warning: passing argument 2 of 'find_e820_area_size' from incompatible pointer type
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fedora reports that mem_init()'s zap_low_mappings(), extended to SMP in
61165d7a x86: fix app crashes after SMP
resume causes 32-bit Intel Mac machines to reboot very early when
booting with EFI.

The EFI code appears to manage low mappings for itself when needed; but
like many before it, confuses PSE with PAE.  So it has only been mapping
half the space it needed when PSE but not PAE.  This remained unnoticed
until we moved the SMP zap_low_mappings() before
efi_enter_virtual_mode().  Presumably could have been noticed years ago
if anyone ran a UP kernel on such machines?
Reported-by: NPeter Jones <pjones@redhat.com>
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Glauber Costa <gcosta@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Tested-by: NPeter Jones <pjones@redhat.com>

Suspend/resume ("echo mem > /sys/power/state") does not work with
vanilla kernels -- the system does not suspend correctly and just
hangs. This patch fixes this so suspend/resume works:

1) of_iomap does not map the whole 0xC000 of the MPC5200 immr so
saving registers does not work.
2) PCI registers need to be saved and restored.
Signed-off-by: NTim Yamin <plasm@roo.me.uk>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The legacy serial driver does not work with an 8250 type UART that is
described in the device tree with the reg-offset and reg-shift
properties.  This change makes legacy_serial ignore these devices.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This change to the makefile corrects the build of a simpleImage with initrd.
Signed-off-by: NJohn Linn <john.linn@xilinx>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

commit 43238382
       x86: change size of node ids from u8 to s16

set the range for NODES_SHIFT to 1..15.

The possible range is 1..9

Fixes Bugzilla #10726
Reported-by: NDave Jones <davej@codemonkey.org.uk>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The symbol account_system_vtime is used by the kvm module but
not exported.  This breaks building with CONFIG_VIRT_CPU_ACCOUNTING
and CONFIG_KVM=m.
Signed-off-by: NDoug Chapman <doug.chapman@hp.com>
Acked-by: NHidetosho Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

On a system where there are no hot pluggable cpus "additional_cpus"
is still set to -1 at the point where we call per_cpu_scan_finalize().
If we didn't find an SRAT table and so pick the default "32" for the
number of cpus, when we get to:
high_cpu = min(high_cpu + reserve_cpus, NR_CPUS);
we will end up initializing for just 31 cpus ... and so we will
die horribly when bringing up cpu#32.

Problem introduced by: 2c6e6db4
"Minimize per_cpu reservations."
Acked-by: NRobin Holt <holt@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

This patch annotates the platform_secondary_init function in
arch/arm/mach-realview/platsmp.c with trace_hardirqs_off to avoid a
warning when LOCKDEP and TRACE_IRQFLAGS are enabled.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When I update kernel 2.6.25 from 2.6.24, gdb does not work.
On 2.6.25, ptrace(PTRACE_GETFPXREGS, ...) returns ENODEV.

But 2.6.24 kernel's ptrace() returns EIO.
It is issue of compatibility.

I attached test program as pt.c and patch for fix it.

#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <signal.h>
#include <errno.h>
#include <sys/ptrace.h>
#include <sys/types.h>

struct user_fxsr_struct {
	unsigned short	cwd;
	unsigned short	swd;
	unsigned short	twd;
	unsigned short	fop;
	long	fip;
	long	fcs;
	long	foo;
	long	fos;
	long	mxcsr;
	long	reserved;
	long	st_space[32];	/* 8*16 bytes for each FP-reg = 128 bytes */
	long	xmm_space[32];	/* 8*16 bytes for each XMM-reg = 128 bytes */
	long	padding[56];
};

int main(void)
{
  pid_t pid;

  pid = fork();

  switch(pid){
  case -1:/*  error */
    break;
  case 0:/*  child */
    child();
    break;
  default:
    parent(pid);
    break;
  }
  return 0;
}

int child(void)
{
  ptrace(PTRACE_TRACEME);
  kill(getpid(), SIGSTOP);
  sleep(10);
  return 0;
}
int parent(pid_t pid)
{
  int ret;
  struct user_fxsr_struct fpxregs;

  ret = ptrace(PTRACE_GETFPXREGS, pid, 0, &fpxregs);
  if(ret < 0){
    printf("%d: %s.\n", errno, strerror(errno));
  }
  kill(pid, SIGCONT);
  wait(pid);
  return 0;
}

/* in the kerel, at kernel/i387.c get_fpxregs() */
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Vegard Nossum reported crashes during cpu hotplug tests:

  http://marc.info/?l=linux-kernel&m=121413950227884&w=4

In function _cpu_up, the panic happens when calling
__raw_notifier_call_chain at the second time. Kernel doesn't panic when
calling it at the first time. If just say because of nr_cpu_ids, that's
not right.

By checking the source code, I found that function do_boot_cpu is the culprit.
Consider below call chain:
 _cpu_up=>__cpu_up=>smp_ops.cpu_up=>native_cpu_up=>do_boot_cpu.

So do_boot_cpu is called in the end. In do_boot_cpu, if
boot_error==true, cpu_clear(cpu, cpu_possible_map) is executed. So later
on, when _cpu_up calls __raw_notifier_call_chain at the second time to
report CPU_UP_CANCELED, because this cpu is already cleared from
cpu_possible_map, get_cpu_sysdev returns NULL.

Many resources are related to cpu_possible_map, so it's better not to
change it.

Below patch against 2.6.26-rc7 fixes it by removing the bit clearing in
cpu_possible_map.
Signed-off-by: NZhang Yanmin <yanmin_zhang@linux.intel.com>
Tested-by: NVegard Nossum <vegard.nossum@gmail.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

WARNING: arch/x86/mm/built-in.o(.text+0x3a1): Section mismatch in
reference from the function set_pte_phys() to the function
.init.text:spp_getpage()
The function set_pte_phys() references
the function __init spp_getpage().
This is often because set_pte_phys lacks a __init
annotation or the annotation of spp_getpage is wrong.

arch/x86/mm/init_64.c: In function 'early_memtest':
arch/x86/mm/init_64.c:520: warning: passing argument 2 of
'find_e820_area_size' from incompatible pointer type
Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Cc: "Linus Torvalds" <torvalds@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

--
WARNING: vmlinux.o(.text+0x721a): Section mismatch in reference from the function ___fill_code_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_code_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_code_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.

WARNING: vmlinux.o(.text+0x7238): Section mismatch in reference from the function ___fill_code_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_code_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_code_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.

WARNING: vmlinux.o(.text+0x7250): Section mismatch in reference from the function ___fill_code_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_code_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_code_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.

WARNING: vmlinux.o(.text+0x7264): Section mismatch in reference from the function ___fill_code_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_code_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_code_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.

WARNING: vmlinux.o(.text+0x72a2): Section mismatch in reference from the function ___fill_data_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_data_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_data_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.

WARNING: vmlinux.o(.text+0x72bc): Section mismatch in reference from the function ___fill_data_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_data_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_data_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.

WARNING: vmlinux.o(.text+0x72d4): Section mismatch in reference from the function ___fill_data_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_data_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_data_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.

WARNING: vmlinux.o(.text+0x72e8): Section mismatch in reference from the function ___fill_data_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_data_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_data_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
--
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Initialize the lock of bad_irq_desc properly.
The content of irq_desc array is replaced by bad_irq_desc in blackfin
arch irqchip init code. So, do it properly as common irq init code.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

This patch updates the kvm host code to use the pvclock structs
and functions, thereby making it compatible with Xen.

The patch also fixes an initialization bug: on SMP systems the
per-cpu has two different locations early at boot and after CPU
bringup.  kvmclock must take that in account when registering the
physical address within the host.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch updates the kvm host code to use the pvclock structs.
It also makes the paravirt clock compatible with Xen.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch updates the xen guest to use the pvclock structs
and helper functions.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Acked-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

This patch adds structs for the paravirt clocksource ABI
used by both xen and kvm (pvclock-abi.h).

It also adds some helper functions to read system time and
wall clock time from a paravirtual clocksource (pvclock.[ch]).
They are based on the xen code.  They are enabled using
CONFIG_PARAVIRT_CLOCK.

Subsequent patches of this series will put the code in use.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Acked-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>

As noted by Akinobu Mita alloc_bootmem and related functions never return
NULL and always return a zeroed region of memory.  Thus a NULL test or
memset after calls to these functions is unnecessary.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The fix applied in e0c6d97c
"security hole in sn2_ptc_proc_write" didn't take into account
the case where count==0 (which results in a buffer underrun
when adding the trailing '\0').  Thanks to Andi Kleen for
pointing this out.
Signed-off-by: NCliff Wickman <cpw@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Call check_sal_cache_flush() after platform_setup() as
check_sal_cache_flush() now relies on being able to call platform
vector code.

Problem was introduced by: 3463a93d
"Update check_sal_cache_flush to use platform_send_ipi()"
Signed-off-by: NJes Sorensen <jes@sgi.com>
Tested-by: NAlex Chiang: <achiang@hp.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Non-PAE operation has been deprecated in Xen for a while, and is
rarely tested or used.  xen-unstable has now officially dropped
non-PAE support.  Since Xen/pvops' non-PAE support has also been
broken for a while, we may as well completely drop it altogether.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Switching msrs can occur either synchronously as a result of calls to
the msr management functions (usually in response to the guest touching
virtualized msrs), or asynchronously when preempting a kvm thread that has
guest state loaded.  If we're unlucky enough to have the two at the same
time, host msrs are corrupted and the machine goes kaput on the next syscall.

Most easily triggered by Windows Server 2008, as it does a lot of msr
switching during bootup.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

KVM has a heuristic to unshadow guest pagetables when userspace accesses
them, on the assumption that most guests do not allow userspace to access
pagetables directly. Unfortunately, in addition to unshadowing the pagetables,
it also oopses.

This never triggers on ordinary guests since sane OSes will clear the
pagetables before assigning them to userspace, which will trigger the flood
heuristic, unshadowing the pagetables before the first userspace access. One
particular guest, though (Xenner) will run the kernel in userspace, triggering
the oops.  Since the heuristic is incorrect in this case, we can simply
remove it.
Signed-off-by: NAvi Kivity <avi@qumranet.com>

kvm_mmu_pte_write() does not handle 32-bit non-PAE large page backed
guests properly. It will instantiate two 2MB sptes pointing to the same
physical 2MB page when a guest large pte update is trapped.

Instead of duplicating code to handle this, disallow directory level
updates to happen through kvm_mmu_pte_write(), so the two 2MB sptes
emulating one guest 4MB pte can be correctly created by the page fault
handling path.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@qumranet.com>