Using better of_property_read_u32() than generic of_get_property().

Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

The SB600 and SB700 southbridge chips from ATI/AMD only have
connections for the primary IDE port. As these chips have unique
pci device ID's use these to mark the secondary port as 'dummy'
Signed-off-by: NDarren Stevens <darren@stevens-zone.net>
Signed-off-by: NTejun Heo <tj@kernel.org>

libata-sff.c checks for legacy mode by testing if both primary and
secondary ports on a controller are in legacy mode and selects legacy
if either one is. However on some south bridge chips (e.g AMD
SB600/SB700) the secondary port is not wired, and when it is disabled
by setting the disable bit in the PCI header it appears as a fixed
legacy port.

Prevent incorrect detection by not testing ports that are marked as
'dummy'

tj: Addressed Sergei's review points.  Other style edits.
Signed-off-by: NDarren Stevens <darren@stevens-zone.net>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

@t1 and @t2i are calculated along with @t2 but never used.  Drop them.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NDavid Binderman <dcb314@hotmail.com>

Ls2088a is new introduced arm-based soc with sata support with
following features:
1. Complies with the serial ATA 3.0 specification and the AHCI 1.3.1
   specification
2. Contains a high-speed descriptor-based DMA controller
3. Supports the following:
   a. Speeds of 1.5 Gb/s (first-generation SATA), 3 Gb/s
      (second-generation SATA), and 6 Gb/s (third-generation SATA)
   b. FIS-based switching
   c. Native command queuing (NCQ) commands
   d. Port multiplier operation
   e. Asynchronous notification
   f. SATA BIST mode
Signed-off-by: NTang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

For ls1021a, and armv8 chasis 2 socs, sata ecc must be disabled.
If ecc register is not found in sata node in dts, report error.

This is a chip erratum described as bellow:
The Read DMA operations get early termination indication from the
controller. This issue is observed as CRC error in the status registers.
The issue is due to address collision at address 0 in the dual port
memory. The read is a dummy read to flush out the header, but due to
collision the controller logs the mbit error reported by the ECC check
logic. This results in the early termination of the Read DMA operation
by the controller. The issue happens to all the interface
speeds(GEN1/2/3) for all the products.

Workaround:
Disable ECC feature on those platforms.
Signed-off-by: NTang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Enable DMA coherence in SATA controller on condition that
dma-coherent property exists in sata node in DTS.
Signed-off-by: NTang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

This reverts commit a234f739.

The commit tried to get rid of the shared global SCSI response buffer.
Unfortunately, it added blocking allocation to atomic path.  Revert it
for now.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>

When CONFIG_HWMON is disabled, we now get a link failure:

ERROR: "devm_hwmon_device_register_with_groups" [drivers/ata/ahci_imx.ko] undefined!
drivers/ata/ahci_imx.o: In function `imx_ahci_probe':
ahci_imx.c:(.text.imx_ahci_probe+0x304): undefined reference to `devm_thermal_zone_of_sensor_register'

This makes the code calling into the hwmon subsystem compile-time
conditional, and adds a Kconfig dependency to avoid the corner
case of having HWMON=m and AHCI_IMX=y, by forcing AHCI_IMX=m in this
case. The thermal subsystem already has a check in its header, but
that also doesn't cover the THERMAL=m case, so we need a somewhat
complex Kconfig expression to handle all cases.

Fixes: 54643a83 ("ahci: imx: Add imx53 SATA temperature sensor support")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NReviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Add Atari Falcon PATA controller driver.  The major difference
when compared to legacy IDE's falconide host driver is that we
are using polled PIO mode and thus avoiding the need for STDMA
locking magic altogether.

Tested under ARAnyM emulator.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

For Atari Falcon PATA support we need to check the current command
in its ->sff_data_xfer method.  Update core code and all users
accordingly.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

When libata was merged m68k lacked IOMAP support.  This has not been
true for a long time now so allow subsystem to be used on m68k.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

Note of the emulated commands in the pageout/pagein path, so just do
a GFP_NOIO dynamic allocation.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NTejun Heo <tj@kernel.org>

No need to copy a zeroed buffer to the caller if the command is defined
to not have a response in the SCSI spec.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NTejun Heo <tj@kernel.org>

We always need to call ->scsi_done after we've finished emulating a
command, so do it in a single place at the end of ata_scsi_simulate.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NTejun Heo <tj@kernel.org>

It's always the scsi_done callback, and we can get at that easily
in the place where ->done is called.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NTejun Heo <tj@kernel.org>

It's only used in libata-scsi.c, so move it closer to the users.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NTejun Heo <tj@kernel.org>

We only need to look at 4 bytes of the inquiry response for ATAPI
devices.  Instead of using the global ata_scsi_rbuf just use a
a stack buffer.  Also factor the fixup into it's own little helper
function to make it more readable.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NTejun Heo <tj@kernel.org>

Replace the sparse 256-pointer array for looking up protocol strings by
a switch() statement to reduce kernel size.

According to bloat-o-meter, this saves 910 bytes on m68k (32-bit), and
1892 bytes on arm64 (64-bit).
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

Convert to devm_ioremap_resource() which provides more consistent error
handling.

Note that devm_ioremap_resource() provides its own error messages.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

For an ATA device supporting the sense data reporting feature set, a
failed command will trigger the execution of ata_eh_request_sense if
the result task file of the failed command has the ATA_SENSE bit set
(sense data available bit). ata_eh_request_sense executes the REQUEST
SENSE DATA EXT command to retrieve the sense data of the failed
command. On success of REQUEST SENSE DATA EXT, the ATA_SENSE bit will
NOT be set (the command succeeded) but ata_eh_request_sense
nevertheless tests the availability of sense data by testing that bit
presence in the result tf of the REQUEST SENSE DATA EXT command.  This
leads us to falsely assume that request sense data failed and to the
warning message:

atax.xx: request sense failed stat 50 emask 0

Upon success of REQUEST SENSE DATA EXT, set the ATA_SENSE bit in the
result task file command so that sense data can be returned by
ata_eh_request_sense.
Signed-off-by: NDamien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org

The header allows GPL v2 only, so declare "GPL v2" for MODULE_LICENSE
Signed-off-by: NUwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

Add a hwmon entry to get the temperature from the die of imx53
SATA.

The original patch was made by Richard Zhu for kernel 2.6.x:
ENGR00134041-MX53-Add-the-SATA-AHCI-temperature-monitor.patch
Signed-off-by: NFabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: NTejun Heo <tj@kernel.org>

Marko reports that CX1-JB512-HP shows the same timeout issues as
CX1-JB256-HP.  Let's apply MAX_SEC_128 to all devices in the series.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NMarko Koski-Vähälä <marko@koski-vahala.com>
Cc: stable@vger.kernel.org # v3.19+

acpi_get_object_info() allocates the returned structure, which the
caller has to free when the call succeeds.  Free it when appropriate.

Fixes: c9802a4b ("ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.")
Signed-off-by: NMichał Kępień <kernel@kempniu.pl>
Signed-off-by: NTejun Heo <tj@kernel.org>

If NO_DMA=y:

    ERROR: "bad_dma_ops" [drivers/ata/libata.ko] undefined!

To fix this, protect the DMA code by #ifdef CONFIG_HAS_DMA, and provide
dummies of ata_sg_clean() and ata_sg_setup() for the !CONFIG_HAS_DMA
case.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

Commit 70e6ad0c ("[PATCH] libata: prepare ata_sg_clean() for
invocation from EH") made ata_sg_clean() global, but no user outside
libata-core.c has ever materialized.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

If NO_DMA=y:

    ERROR: "bad_dma_ops" [drivers/ata/libahci_platform.ko] undefined!
    ERROR: "dmam_alloc_coherent" [drivers/ata/libahci.ko] undefined!

Add a block dependency on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

If NO_DMA=y:

    ERROR: "dmam_alloc_coherent" [drivers/ata/libata.ko] undefined!

Add a dependency on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

If NO_DMA=y:

    ERROR: "bad_dma_ops" [drivers/ata/sata_highbank.ko] undefined!

Add a dependency on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

If NO_DMA=y:

    ERROR: "dma_pool_alloc" [drivers/ata/sata_mv.ko] undefined!
    ERROR: "dmam_pool_create" [drivers/ata/sata_mv.ko] undefined!
    ERROR: "dma_pool_free" [drivers/ata/sata_mv.ko] undefined!

Add a dependency on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTejun Heo <tj@kernel.org>

Merge tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver fixes from Darren Hart:
 "Just two small fixes for platform drivers x86:

   - use brightness_set_blocking for LED-setting callbacks on Fujitsu
     laptops

   - fix surface3_button build errors"

* tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  platform/x86: fujitsu-laptop: use brightness_set_blocking for LED-setting callbacks
  platform/x86: fix surface3_button build errors

Pull audit fixes from Paul Moore:
 "Two small fixes relating to audit's use of fsnotify.

  The first patch plugs a leak and the second fixes some lock
  shenanigans. The patches are small and I banged on this for an
  afternoon with our testsuite and didn't see anything odd"

* 'stable-4.10' of git://git.infradead.org/users/pcmoore/audit:
  audit: Fix sleep in atomic
  fsnotify: Remove fsnotify_duplicate_mark()

Pull i915 drm fixes from Jani Nikula:
 "Here's a bunch of drm/i915 fixes for v4.10-rc3. It includes GVT-g
  fixes.

  My new year's resolution is to start using signed tags for pulls. If
  that feels like a déjà vu, it's ((new year's) resolution), not (new
  (year's resolution))"

[ Taking this directly from Jani because Dave Airlie is only partially
  connected right now.  - Linus ]

* tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel:
  drm/i915: Prevent timeline updates whilst performing reset
  drm/i915: Silence allocation failure during sg_trim()
  drm/i915: Don't clflush before release phys object
  drm/i915: Fix oops in overlay due to frontbuffer tracking
  drm/i915: Fix oopses in the overlay code due to i915_gem_active stuff
  drm/i915: Initialize overlay->last_flip properly
  drm/i915: Move the min_pixclk[] handling to the end of readout
  drm/i915: Force VDD off on the new power seqeuencer before starting to use it
  drm/i915/gvt: fix typo in cfg_space range check
  drm/i915/gvt: fix an issue in emulating cfg space PCI_COMMAND
  drm/i915/gvt/kvmgt: trival: code cleanup
  drm/i915/gvt/kvmgt: prevent double-release of vgpu
  drm/i915/gvt/kvmgt: check returned slot for gfn
  drm/i915/gvt/kvmgt: dereference the pointer within lock
  drm/i915/gvt: reset the GGTT entry when vGPU created
  drm/i915/gvt: fix an error in opregion handling

Pull pin control fixes from Linus Walleij:
 "Three small pin control fixes for the v4.10 series. Very little to say
  about them, just driver fixes.

   - one fix to the AMD pinctrl ACPI glue

   - fix requests on the Meson driver

   - fix bitfield widths on Samsungs Exynos 5433"

* tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: samsung: Fix the width of PINCFG_TYPE_DRV bitfields for Exynos5433
  pinctrl: meson: fix gpio request disabling other modes
  pinctrl/amd: Set the level based on ACPI tables

Pull ARM SoC fixes from Arnd Bergmann:
 "This is a rather large set of bugfixes, as we just returned from the
  Christmas break. Most of these are relatively unimportant fixes for
  regressions introduced during the merge window, and about half of the
  changes are for mach-omap2.

  A couple of patches are just cleanups and dead code removal that I
  would not normally have considered for merging after -rc2, but I
  decided to take them along with the fixes this time.

  Notable fixes include:

   - removing the skeleton.dtsi include broke a number of machines, and
     we have to put empty /chosen nodes back to be able to pass kernel
     command lines as before

   - enabling Samsung platforms no longer hardwires CONFIG_HZ to 200, as
     it had been for no good reason for a long time"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
  MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
  drivers: psci: annotate timer on stack to silence odebug messages
  ARM64: defconfig: enable DRM_MESON as module
  ARM64: dts: meson-gx: Add Graphic Controller nodes
  ARM64: dts: meson-gxl: fix GPIO include
  ARM: dts: imx6: Disable "weim" node in the dtsi files
  ARM: dts: qcom: apq8064: Add missing scm clock
  ARM: davinci: da8xx: Fix sleeping function called from invalid context
  ARM: davinci: Make __clk_{enable,disable} functions public
  ARM: davinci: da850: don't add emac clock to lookup table twice
  ARM: davinci: da850: fix infinite loop in clk_set_rate()
  ARM: i.MX: remove map_io callback
  ARM: dts: vf610-zii-dev-rev-b: Add missing newline
  ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
  ARM: dts: imx31: fix AVIC base address
  ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
  arm64: dts: vexpress: Support GICC_DIR operations
  ARM: dts: vexpress: Support GICC_DIR operations
  firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
  arm64: dts: msm8996: Add required memory carveouts
  ...

Pull xen fixes and cleanups from Juergen Gross:

 - small fixes for xenbus driver

 - one fix for xen dom0 boot on huge system

 - small cleanups

* tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Xen: ARM: Zero reserved fields of xatp before making hypervisor call
  xen: events: Replace BUG() with BUG_ON()
  xen: remove stale xs_input_avail() from header
  xen: return xenstore command failures via response instead of rc
  xen: xenbus driver must not accept invalid transaction ids
  xen/evtchn: use rb_entry()
  xen/setup: Don't relocate p2m over existing one

Rather than keep a list of all possible compression types in the
Makefile, set the target explicitly from Kconfig.
Reviewed-by: NFrancisco Blas Izquierdo Riera (klondike) <klondike@klondike.es>
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>