Should probably just init this in the GMbus code all the time, based on
the cdclk and HPLL like we do on newer platforms.  Ville has code for
that in a rework branch, but until then we can fix this bug fairly
easily.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76301Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NNikolay <mar.kolya@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

When bind failed make sure that CRTC and planes are
completely clean up to avoid properties duplication.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

High Quality Video Data Plane is hardware IP dedicated
to video rendering. Compare to GPD (graphic planes) it
have better scaler capabilities.

HQVDP use VID layer to push data into hardware compositor
without going into DDR. From data flow point of view HQVDP
and VID are nested so HQVPD update/disable VID.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

stih407 SoC have a dedicated hardware cursor plane,
this patch enable it.
The hardware have a color look up table, fix it to
be able to use ARGB8888.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

For stih407 SoC enable the second mixer to get two CRTC.
Allow GPD planes and encoders to be connected to this new CRTC.
Cursor plane can only be set on first CRTC.
GPD clocks needed change the parent clock depending on which
CRTC GPD are used.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

The HDMI path introduce a delay of 6 pixels.
This delay should be take into account while programming
VTG for the HDMI. Without this delay, the HDMI active
window area is shift of 6 pixel on the right.

Set also timing for DVO output.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Change some functions prototype to prepare the introduction of
auxiliary crtc. It will also help to have a DVO encoder.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Make sure that vblank is enabled when crtc commit is call.
Replace drm_vblank_off() by drm_crtc_vblank_off()
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

The hardware expect to have the infoframe checksum in the first byte.
In consequence shift all infoframe on one byte.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Stop use event_lock in vblank disable function.
This was creating a dead lock.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Store the physical address at node creation time
to avoid use of virt_to_dma and dma_to_virt everywhere
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Make sure that mixer control register is correctly reset
before use it.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

gpio used for HDMI hot plug detection is useless,
HDMI_STI register contains an hot plug detection status bit.
Fix binding documentation.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

Depending of the board configuration i2c for ddc could change,
this patch allow to use a phandle to specify which i2c controller to use.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>

We may be hidding bugs by doing that, so let remove it and have the
actual mask value shine through, for better or worse.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

While trying to unify the order of those arguments throughout the
driver, Daniel noticed what we were inverting them in this part of the
code.
Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Drivers where the DRM objects have a lifetime that extends beyond that
of the DRM device need to zero out the DRM object memory to void stale
data such as properties. The DRM core code expects to operate on newly
allocated and zeroed out objects and will behave unexpectedly, such as
add duplicate properties, otherwise.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I was playing with clang and oh surprise! a warning trigerred by
-Wshift-overflow (gcc doesn't have this one):

    WA_SET_BIT_MASKED(GEN7_GT_MODE,
                      GEN6_WIZ_HASHING_MASK | GEN6_WIZ_HASHING_16x4);

    drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
      (0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
      [-Wshift-overflow]
        WA_SET_BIT_MASKED(GEN7_GT_MODE,
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
      'WA_SET_BIT_MASKED'
        WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)

Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.

The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.

To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.

This bug was introduced when reworking the WA emission in:

  Commit 7225342a
  Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
  Date:   Tue Oct 7 17:21:26 2014 +0300

      drm/i915: Build workaround list in ring initialization

v2: Invert the order of the mask and value arguments (Daniel Vetter)
    Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
    _MASKED_FIELD() (Jani Nikula)
    Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
    Add check to ensure the value is within the mask boundaries (Chris Wilson)

v3: Ensure the the value and mask are 16 bits (Dave Gordon)

Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Apparently stuff works that way on those machines.

I agree with Chris' concern that this is a bit risky but imo worth a
shot in -next just for fun. Afaics all these machines have the pci
resources allocated like that by the BIOS, so I suspect that it's all
ok.

This regression goes back to

commit eaba1b8f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu Jul 4 12:28:35 2013 +0100

    drm/i915: Verify that our stolen memory doesn't conflict

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76983
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71031Tested-by: Nlu hua <huax.lu@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMartin Peres <martin.peres@free.fr>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Spotted while reviewing the DRM changes in Linux 3.18 for LinuxFR.

CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMartin Peres <martin.peres@free.fr>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds fbdev/con support for tiled monitors, so that we
only set a mode on the correct half of the monitor, or
span the two halves if needed.

v2: remove unneeded ERROR, fix | vs ||
Signed-off-by: NDave Airlie <airlied@redhat.com>

This takes the tiling info from the connector and
exposes it to userspace, as a blob object in a
connector property.

The contents of the blob is ABI.

v2: add property + function documentation.

v3: move property setup from previous patch.
add boilerplate + fix long line (Daniel)
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This creates a tile group from DisplayID block, and
stores the pieces of parsed info from the DisplayID block
into the connector.

v2: add missing signoff, add new connector bits to docs.

v3: remove some debugging.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Logical ports are never going to have EDID changes,
they are used for the internal ports on MST monitors.

We cache the EDIDs from these to save time at MST probe.

v2: drop misplace tile property line, meant for other patch.
Signed-off-by: NDave Airlie <airlied@redhat.com>

A tile group is an identifier shared by a single monitor,
DisplayID topology has 8 bytes we can use for this, just
use those for now until something else comes up in the
future. We assign these to an idr and use the idr to
tell userspace what connectors are in the same tile group.

DisplayID v1.3 says the serial number must be unique for
displays from the same manufacturer.

v2:
destroy idr (dvdhrm)
add docbook (danvet)
airlied:- not sure how to make docbook add fns to tile group section.

v3: fix missing unlock.
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When we unplug a dp mst branch we unreference the entire tree from
the root towards the leaves. Which is ok, since that's the way the
pointers and so also the refcounts go.

But when we drop the reference we must make sure that we remove the
branches/ports from the lists/pointers before dropping the reference.
Otherwise the get_validated functions will still return it instead
of returning NULL (which indicates a potentially on-going unplug).

The mst branch destroy gets this right for ports: First it deletes
the port from the ports list, then it unrefs. But the ports destroy
function gets it wrong: First it unrefs, then it drops the ref. Which
means a zombie mst branch can still be validate with get_validated_mstb_ref
when it shouldn't.

Fix this.

This should address a backtrace Dave dug out somewhere on unplug:

 [<ffffffffa00cc262>] drm_dp_mst_get_validated_mstb_ref_locked+0x92/0xa0 [drm_kms_helper]
 [<ffffffffa00cc211>] drm_dp_mst_get_validated_mstb_ref_locked+0x41/0xa0 [drm_kms_helper]
 [<ffffffffa00cc2aa>] drm_dp_get_validated_mstb_ref+0x3a/0x60 [drm_kms_helper]
 [<ffffffffa00cc2fb>] drm_dp_payload_send_msg.isra.14+0x2b/0x100 [drm_kms_helper]
 [<ffffffffa00cc547>] drm_dp_update_payload_part1+0x177/0x360 [drm_kms_helper]
 [<ffffffffa015c52e>] intel_mst_disable_dp+0x3e/0x80 [i915]
 [<ffffffffa013d60b>] haswell_crtc_disable+0x1cb/0x340 [i915]
 [<ffffffffa0136739>] intel_crtc_control+0x49/0x100 [i915]
 [<ffffffffa0136857>] intel_crtc_update_dpms+0x67/0x80 [i915]
 [<ffffffffa013fa59>] intel_connector_dpms+0x59/0x70 [i915]
 [<ffffffffa015c752>] intel_dp_destroy_mst_connector+0x32/0xc0 [i915]
 [<ffffffffa00cb44b>] drm_dp_destroy_port+0x6b/0xa0 [drm_kms_helper]
 [<ffffffffa00cb588>] drm_dp_destroy_mst_branch_device+0x108/0x130 [drm_kms_helper]
 [<ffffffffa00cb3cd>] drm_dp_port_teardown_pdt+0x3d/0x50 [drm_kms_helper]
 [<ffffffffa00cdb79>] drm_dp_mst_handle_up_req+0x499/0x540 [drm_kms_helper]
 [<ffffffff810d9ead>] ? trace_hardirqs_on_caller+0x15d/0x200 [<ffffffffa00cdc73>]
 drm_dp_mst_hpd_irq+0x53/0xa00 [drm_kms_helper] [<ffffffffa00c7dfb>]
 ? drm_dp_dpcd_read+0x1b/0x20 [drm_kms_helper] [<ffffffffa0153ed8>]
 ? intel_dp_dpcd_read_wake+0x38/0x70 [i915] [<ffffffffa015a225>]
 intel_dp_check_mst_status+0xb5/0x250 [i915] [<ffffffffa015ac71>]
 intel_dp_hpd_pulse+0x181/0x210 [i915] [<ffffffffa01104f6>]
 i915_digport_work_func+0x96/0x120 [i915]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

On MST systems the monitors don't appear when we set the fb up,
but plymouth opens the drm device and holds it open while they
come up, when plymouth finishes and lastclose gets called we
don't do the delayed fb probe, so the monitor never appears on the
console.

Fix this by moving the delayed checking into the mode restore.

v2: Daniel suggested that ->delayed_hotplug is set under
the mode_config mutex, so we should check it under that as
well, while we are in the area.
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

At least on two MST devices I've tested with, when
they are link training downstream, they are totally
unable to handle aux ch msgs, so they defer like nuts.
I tried 16, it wasn't enough, 32 seems better.

This fixes one Dell 4k monitor and one of the
MST hubs.

v1.1: fixup comment (Tom).
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Otherwise the MST resume paths can hit DPMS paths
which hit state checker paths, which hit WARN_ON,
because the state checker is inconsistent with the
hw.

This fixes a bunch of WARN_ON's on resume after
undocking.
Signed-off-by: NDave Airlie <airlied@redhat.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

This patch checks if the process that opens the /dev/kfd device is 32-bit
process. If so, it returns -EPERM and prints a warning message in dmesg.

This is done to prevent 32-bit user processes from using amdkfd, and hence, HSA
features.

AMD's HSA userspace stack will also support only 64-bit processes on Linux.
Reviewed-by: NAlexey Skidanov <alexey.skidanov@amd.com>
Signed-off-by: NOded Gabbay <oded.gabbay@amd.com>

The watchdog mask bit offset listed for Exynos7 is incorrect.
Fix this.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Naveen Krishna Chatradhi <naveenkrishna.ch@gmail.com
Reviewd-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

So apparently jiffies<->nsec<->ktime isn't accurate or something. At
elast if we timeout there's occasionally still a few hundred us left
(in a 2 second timeout).

Stuff I've tried and thrown out again:
- Sampling the before timestamp before jiffies. Doesn't improve test
  path rate at all.
- Using jiffies. Way to inaccurate, which means way too much drift
  with signals plus automatic ioctl restarting in userspace. In
  hindsight we should have used an absolute timeout, but hey we need
  something for v3 of the i915 gem wait interfaces ;-)
- Trying to figure out where accuracy gets lost. gl testcase really
  don't care all that much about this (as long as isn't not massively
  off), it's just that the testcase gets a bit upset if it receives an
  EITME with timeout > 0.

So as long as we're in the ballbark it's good enough. So patch
everything up if we're at most one jiffies off. I get's me a solid
test again.

This regression is probably introduced in

commit 5ed0bdf2
Author: Thomas Gleixner <tglx@linutronix.de>
Date:   Wed Jul 16 21:05:06 2014 +0000

    drm: i915: Use nsec based interfaces

    Use ktime_get_raw_ns() and get rid of the back and forth timespec
    conversions.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Probably because I'm too lazy to confirm myself and still waiting for
QA ;-)

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82749Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

We've lost the +1 required for correct timeouts in

commit 5ed0bdf2
Author: Thomas Gleixner <tglx@linutronix.de>
Date:   Wed Jul 16 21:05:06 2014 +0000

    drm: i915: Use nsec based interfaces

    Use ktime_get_raw_ns() and get rid of the back and forth timespec
    conversions.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

So fix this up by reinstating our handrolled _timeout function. While
at it bother with handling MAX_JIFFIES.

v2: Convert to usecs (we don't care about the accuracy anyway) first
to avoid overflow issues Dave Gordon spotted.

v3: Drop the explicit MAX_JIFFY_OFFSET check, usecs_to_jiffies should
take care of that already. It might be a bit too enthusiastic about it
though.

v4: Chris has a much nicer color, so use his implementation.

This requires to export nsec_to_jiffies from time.c.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82749
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Acked-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Partial revert of

commit 20664591
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Wed Nov 5 14:26:09 2014 -0800

    drm/i915: check for audio and infoframe changes across mode sets v2

References: https://bugs.freedesktop.org/show_bug.cgi?id=86683Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NLi Xu <li.l.xu@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: NVishnu Motghare <vishnum@xilinx.com>
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]

Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).

For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:

S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->

The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.

Hence, fix it by generating Stop condition (STP) always when NACK is received.

This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a ("i2c: omap: query STP always when NACK is received").
Reviewed-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: NHein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Just like 0x1600 which got blacklisted by 66a7cbc3 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled.  Disable MSI.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NDominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171
Cc: stable@vger.kernel.org

Note that the read manpages explicitly states that the read position
is undefined on error. Since EFAULT is just a userspace bug we are
therefore fine with just dropping the event on the floor.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
[danvet: Add note that just dropping the event is ok.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In function acquire_packet_buffer() we may return -ENOMEM. In that case, we
should set the *buffer_ptr to NULL, so that calling functions which check the
*buffer_ptr value as a criteria for success, will know that
acquire_packet_buffer() failed.
Reviewed-by: NAlexey Skidanov <alexey.skidanov@amd.com>
Signed-off-by: NOded Gabbay <oded.gabbay@amd.com>