Allocate, and then map the receive skb before writing any data to the
ring descriptor or storing the skb.  When freeing the receive ring
entries, unmap and free the skb, and then clear the stored skb pointer.

This means we have ring data and skb pointer in one of two states:
either both fully setup, or nothing setup.

This simplifies the cleanup, as we can use just the skb pointer to
indicate whether the descriptor is setup, and thus avoids potentially
calling dma_unmap_single() on a DMA error value.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls.  At this point, the driver then clears
fep->opened.  The NAPI poll function uses this to stop processing in
the receive path.  Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.

Therefore, this variable serves no purpose, so let's remove it.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the network interface goes down, stop the phy to prevent further
link up status changes before taking the MAC or netif sections down.
This prevents further reception of link up events which could
potentially call fec_restart().

Since phy_stop() takes the mutex which adjust_link() runs under, we
also ensure that adjust_link() will not already be processing a link
up event.

We also need to do this when suspending as well - we don't want a
mis-timed phy state change to restart the MAC after we have stopped
it for suspend, and thus need to restart the phy when resuming.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we disconnect from a phy, we should forget our pointer to it so we
don't accidentally try to configure it.  We handle a NULL phy pointer
correctly in most places, except fec_enet_set_pauseparam().  Fix this
too.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fep->phy_dev can not be NULL here for two reasons:
- fec_enet_open() will have successfully connected the phy, or will have
  failed.
- fec_enet_open() will have called phy_start(fep->phy_dev), which
  unconditionally dereferences this pointer.

If it were to be NULL here, then fec_enet_open() will have already
oopsed.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use netif_stop_queue() in several places where we want to ensure that
the start_xmit function is not running.  netif_stop_queue() is not
sufficient to achieve that - it merely sets a flag to indicate that the
transmit queue(s) should not be run.

netif_tx_disable() gives this guarantee, since it takes the transmit
queue lock while marking the queue stopped.  This will wait for the
transmit function to complete before returning.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While running: while :; do iperf -c <HOST> -P 4; done, transmit timeouts
are regularly reported.  With the tx ring dumping in place, we can see
that all entries are in use, and the hardware has finished transmitting
these packets.  However, the driver has not reclaimed these ring
entries.

This can occur if the interrupt handler is invoked at the wrong moment -
eg:

	CPU0				CPU1
	fec_enet_tx()
					interrupt, IEVENT = FEC_ENET_TXF
					FEC_ENET_TXF cleared
					napi_schedule_prep()
	napi_complete()

The result is that we clear the transmit interrupt, but we don't trigger
any cleaning of the transmit ring.  Instead, use a different strategy:

- When receiving a transmit or receive interrupt, disable both tx and rx
  interrupts, but do not acknowledge them.  Schedule a napi poll.  Don't
  loop.

- When we are polled, read IEVENT, acknowledging the pending transmit
  and receive interrupts, before then going on to process the
  appropriate rings.

This allows us to avoid the race, and has a number of other advantages:
- we cut down on the number of transmit interrupts we have to process.
- we only look at the rings which have pending events.
- we gain additional throughput: the iperf total bandwidth increases
  from about 180Mbps to 240Mbps:

[  3]  0.0-10.0 sec  68.1 MBytes  57.0 Mbits/sec
[  5]  0.0-10.0 sec  72.4 MBytes  60.5 Mbits/sec
[  4]  0.0-10.1 sec  76.1 MBytes  63.5 Mbits/sec
[  6]  0.0-10.1 sec  71.9 MBytes  59.9 Mbits/sec
[SUM]  0.0-10.1 sec   288 MBytes   241 Mbits/sec
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting the pause parameters causes a running network interface to be
restarted.  However, the restart forces the FEC into half-duplex mode,
whether or not the remote end is in half-duplex mode.  Misconfigured
duplex mode is a known source of problems on a link.

Fix this by always preserving the duplex mode on configuration changes.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The iMX6 gigabit FEC does not support half-duplex gigabit operation.
Phys attacked to the FEC may support this, and we currently do nothing
to disable this feature.  This may result in an invalid configuration.
Mask out phy support for gigabit half-duplex operation.
Acked-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
net: Improvements and applications of packet flow hash in transmit path

This patch series includes some patches which improve and make use
of skb->hash in the transmit path.

What is included:

- Infrastructure to save a precomputed hash in the sock structure.
  For connected TCP and UDP sockets we only need to compute the
  flow hash once and not once for every packet.
- Call skb_get_hash in get_xps_queue and __skb_tx_hash. This eliminates
  the awkward access to skb->sk->sk_hash in the lower transmit path.
- Move UDP source port generation into a common function in udp.h This
  implementation is mostly based on vxlan_src_port.
- Use non-zero IPv6 flow labels in flow_dissector as port information
  for flow hash calculation.
- Implement automatic flow label generation on transmit (per RFC 6438).
- Don't repeatedly try to compute an L4 hash in skb_get_hash if we've
  already tried to find one in software stack calculation.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add sw_hash flag to skbuff to indicate that skb->hash was computed
from flow_dissector. This flag is checked in skb_get_hash to avoid
repeatedly trying to compute the hash (ie. in the case that no L4 hash
can be computed).
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Automatically generate flow labels for IPv6 packets on transmit.
The flow label is computed based on skb_get_hash. The flow label will
only automatically be set when it is zero otherwise (i.e. flow label
manager hasn't set one). This supports the transmit side functionality
of RFC 6438.

Added an IPv6 sysctl auto_flowlabels to enable/disable this behavior
system wide, and added IPV6_AUTOFLOWLABEL socket option to enable this
functionality per socket.

By default, auto flowlabels are disabled to avoid possible conflicts
with flow label manager, however if this feature proves useful we
may want to enable it by default.

It should also be noted that FreeBSD has already implemented automatic
flow labels (including the sysctl and socket option). In FreeBSD,
automatic flow labels default to enabled.

Performance impact:

Running super_netperf with 200 flows for TCP_RR and UDP_RR for
IPv6. Note that in UDP case, __skb_get_hash will be called for
every packet with explains slight regression. In the TCP case
the hash is saved in the socket so there is no regression.

Automatic flow labels disabled:

  TCP_RR:
    86.53% CPU utilization
    127/195/322 90/95/99% latencies
    1.40498e+06 tps

  UDP_RR:
    90.70% CPU utilization
    118/168/243 90/95/99% latencies
    1.50309e+06 tps

Automatic flow labels enabled:

  TCP_RR:
    85.90% CPU utilization
    128/199/337 90/95/99% latencies
    1.40051e+06

  UDP_RR
    92.61% CPU utilization
    115/164/236 90/95/99% latencies
    1.4687e+06
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the receive side to support RFC 6438 which is to
use the flow label as an ECMP hash. If an IPv6 flow label is set
in a packet we can use this as input for computing an L4-hash. There
should be no need to parse any transport headers in this case.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In vxlan and OVS vport-vxlan call common function to get source port
for a UDP tunnel. Removed vxlan_src_port since the functionality is
now in udp_flow_src_port.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds udp_flow_src_port function which is intended to be
a common function that UDP tunnel implementations call to set the source
port. The source port is chosen so that a hash over the outer headers
(IP addresses and UDP ports) acts as suitable hash for the flow of the
encapsulated packet. In this manner, UDP encapsulation works with RSS
and ECMP based wrt the inner flow.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call standard function to get a packet hash instead of taking this from
skb->sk->sk_hash or only using skb->protocol.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For a connected socket we can precompute the flow hash for setting
in skb->hash on output. This is a performance advantage over
calculating the skb->hash for every packet on the connection. The
computation is done using the common hash algorithm to be consistent
with computations done for packets of the connection in other states
where thers is no socket (e.g. time-wait, syn-recv, syn-cookies).

This patch adds sk_txhash to the sock structure. inet_set_txhash and
ip6_set_txhash functions are added which are called from points in
TCP and UDP where socket moves to established state.

skb_set_hash_from_sk is a function which sets skb->hash from the
sock txhash value. This is called in UDP and TCP transmit path when
transmitting within the context of a socket.

Tested: ran super_netperf with 200 TCP_RR streams over a vxlan
interface (in this case skb_get_hash called on every TX packet to
create a UDP source port).

Before fix:

  95.02% CPU utilization
  154/256/505 90/95/99% latencies
  1.13042e+06 tps

  Time in functions:
    0.28% skb_flow_dissect
    0.21% __skb_get_hash

After fix:

  94.95% CPU utilization
  156/254/485 90/95/99% latencies
  1.15447e+06

  Neither __skb_get_hash nor skb_flow_dissect appear in perf
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the hash computation located in __skb_get_hash to be a separate
function which takes flow_keys as input. This will allow flow hash
computation in other contexts where we only have addresses and ports.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: PM and Wake-on-LAN support

This patchset brings Power Management and Wake-on-LAN support to the
Broadcom SYSTEM PORT driver.

S2 and S3 modes are supported, while we only support Wake-on-LAN using
MagicPackets for now
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for Wake-on-LAN using Magic Packet with or without SecureOn
password is implemented doing the following:

- setting the password to the relevant UniMAC registers
- flagging the device as a wakeup source for the system, as well as
  its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- enabling the MPD interrupt to wake us

The Device Tree binding documentation is also reflected to specify the
third optional Wake-on-LAN interrupt line.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This boolean tells us whether we are using the RXCHK hardware block,
so use a variable name that reflects that. RXCHK might be used in the
future to implement Wake-on-LAN using ARP or unicast packets.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the hardware recommended suspend/resume procedure for
SYSTEMPORT. We leverage the previous factoring work such that we can
logically break all suspend/resume operations into disctint RX and TX
code paths.

When the system enters S3, we will loose all register contents, so
make sure that we correctly re-program all the hardware and software
views of the RX & TX rings as well.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor common code that either enables or disables the network
interface with the networking stack. We are going to reuse these
functions for suspend/resume callbacks.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quite often we need to enable either the transmitter or the receiver
bits in UMAC_CMD, use umac_enable_set() to do that for us.

This is a preliminary change to introduce suspend/resume support in the
driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixed the coding style issues reported by checkpatch.pl

following issues fixed:
	CHECK: Alignment should match open parenthesis
	WARNING: line over 80 characters
	CHECK: Blank lines aren't necessary before a close brace '}'
	WARNING: networking block comments don't use an empty /* line, use /* Comment...
	WARNING: Missing a blank line after declarations
	WARNING: networking block comments start with * on subsequent lines
	CHECK: braces {} should be used on all arms of this statement
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Tested-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the prototype of the do_one_broadcast() method so that it will return void.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Erik Hugne says:

====================
tipc: link state processing improvements

Message delivery is separated from the link state processing, and
we fix a bug in receive-path triggered acks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Link state acks triggered from the receive path is done before
the last received packet have been processed by the link layer.
The effect of this is that the last received packet will not be
included in the ack. This causes problems if the link window is
set to TIPC_MIN_LINK_WIN, where the ack interval will be equal to
the link tolerance, and the link enters a stop-and-go behavior.
We move the ack logic to after link state processing, just before
the packet is delivered to higher layers.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NCarl Sigurjonsson <carl.sigurjonsson@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a cosmetic change, separating message delivery from the
link state processing.
Signed-off-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always store in snt_synack the time at which the server received the
first client SYN and attempted to send the first SYNACK.

Recent commit aa27fc50 ("tcp: tcp_v[46]_conn_request: fix snt_synack
initialization") resolved an inconsistency between IPv4 and IPv6 in
the initialization of snt_synack. This commit brings back the idea
from 843f4a55 (tcp: use tcp_v4_send_synack on first SYN-ACK), which
was going for the original behavior of snt_synack from the commit
where it was added in 9ad7c049 ("tcp: RFC2988bis + taking RTT
sample from 3WHS for the passive open side") in v3.1.

In addition to being simpler (and probably a tiny bit faster),
unconditionally storing the time of the first SYNACK attempt has been
useful because it allows calculating a performance metric quantifying
how long it took to establish a passive TCP connection.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Jerry Chu <hkchu@google.com>
Acked-by: NOctavian Purdila <octavian.purdila@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ondrej Zary says:

====================
tlan: Link handling improvements and Olicom fixes

This patch series improves link handling in tlan driver, allowing the
cable to be (un)plugged anytime and NetworkManager to work properly.

Also there are some bugfixes related to Olicom OC-2326 card.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using internal 10 Mbps PHY, isolate the external PHY from MII bus.
External PHY must be kept powered up because it passes TX from tlan chip to
network.

This fixes weird link-loss problems under load with OC-2326 card at 10 Mbps.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_disable_device() is called in _suspend but there's no corresponding
pci_enable_device() in _resume.
This causes "disabling already-disabled device" warning on 2nd suspend.

Add pci_enable_device() call to _resume to fix this problem.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tlan_reset_adapter, we disable internal PHY when an external one is used.
On cards which use internal PHY in 10 Mbps mode, we enable it later when
setting 10 Mbps mode but it does not really work (PHY fails to reset).
Leave it enabled instead.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a timeout to prevent infinite loop waiting for PHY to reset.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the autonegotiation poll interval from 8 seconds to 2.
This greatly reduces the time needed to detect link presence,
especially on Olicom cards at 10 Mbps (two autonegoatiations required).
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove excess printks when the link is down.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When link is lost on a card which uses internal PHY for 10 Mbit speeds,
restart autonegotiation to allow switching between 10 and 100 Mbps speeds.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Olicom OC-2325 and OC-2326 cards have the MAC address byte-swapped in EEPROM.
Byte-swap the MAC address if it's located at offset 0xF8.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic ethtool support to tlan driver:
 - driver info  - link detect (this allows NetworkManager to detect carrier)
 - EEPROM read
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>