The receive buffer offset is constant in this driver.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

No need to grap full size MTU buffer for possibly small transmit
bounce buffers.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make the PHY and statistic timer run on one second boundary
for powersaving.

On resume, the driver should check for link up immediately, to
get online faster (rather than waiting for the next second).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The chip executes microcode present in internal RAM,
whose content is loaded from EEPROM on power cycle.
This patch allows an update of the microcode through PIO
without forcing a power cycle.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update FW to 4.1.
Proceed to subsequent HW tuning to improve RDMA perfs..
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Streamline sge page management.
Fix dma mappings when buffers are recycled.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Recent gcc versions emit warnings when unsigned variables are compared < 0 or >= 0.
Signed-off-by: NBill Nottingham <notting@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

fmvj18x_cs:
      NEC PK-UG-J001
      Panasonic CF-VML201
      Panasonic TO-PDL9610

pcnet_cs:
       MICRO-RESEARCH  MC336LAN
Signed-off-by: NKomuro <komurojun-mbn@nifty.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Whitespace updates for usbnet core, mostly switching to tab-only indents.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If connected via SGMII, initialize with SGMII mode configured.
Signed-off-by: NKapil Juneja <Kapil.Juneja@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add code for initialising and configuring TBI interface and
programming it for connecting to on-chip SERDES (Lynx PHY)
in case of SGMII mode selected through HRCW at reset.

also add defines for TBI register configuration. TBI
interface is programmed towards the SERDES.

refactored mdio read/write functions to differentiate
programming local interface MII regs (e.g., for TBI) from
always programming the mdio master (TSEC1, for programming
the PHYs).
Signed-off-by: NKapil Juneja <Kapil.Juneja@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The ICPlus IP175C sports a 100Mbit/s 4-port switch in addition
to a dedicated 100Mbit/s WAN port.
Signed-off-by: NMichael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

s2io cleanup suggestions, per discussion on mailing lists.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds PCI error recovery support to the
s2io 10-Gigabit ethernet device driver. Third revision,
blocks interrupts and the watchdog.

Tested, seems to work well.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Acked-by: NRamkrishna Vepa <Ramkrishna.Vepa@neterion.com>
Cc: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Cc: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver version number has not been updated since the driver was
included in the main kernel tree and there is no plan on updating this
in the future either. At this point, the only correct way to refer to
the version is to use the kernel version. The 0.4.4 version is
confusing since there are external version with higher version number
even though they are not actually any newer than the in-tree version.

Let's get rid of the version number in the kernel tree in order to
avoid this kind of confusion.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use list_for_each_entry() instead of manual iteration and
substitute some list_for_each() loops with list_for_each_entry().
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This may be useful in mesh setups when most stations act as repeaters only.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleanup using list_for_each_entry.

Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Joe Jezak <josejx@gentoo.org>
Cc: Daniel Drake <dsd@gentoo.org>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A disagreement between the specifications and the bcm43xx code has just
been discovered and is hereby fixed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vendor driver code suggests that CR47 patching happens on every channel
change for every RF (depending on bit 8 in POD).

Due to a bug in their driver (upper bits of RF_Mode get zeroed out, then
are examined for 1s when setting some other flags), this isn't actually
what happens, and their generic CCK patching routine never takes effect.

Some of their RF configurations do include explicit (duplicated) code
for CR47 patching though. This patch makes zd1211rw match that
behaviour.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for another radio appearing in new devices: the
Ubec UW2453. It's more complicated than the other RF's we support, but
Ubec publish full tech specs so we're able to understand the vendor code
relatively well.

Now that we support UW2453, we also support Atheros' new USB chip: the
AR5007UG. From the little info we have, this appears to be just a
rebranded ZD1211B.

This RF code doesn't work very well -- lots more TX/RX errors than the
other RFs. However, the vendor driver doesn't do any better, so this is
all we can do for now.

[kune@deine-taler.de: bug fixes]
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These changes are needed for UW2453 RF support:

Add pointer which RF drivers can use to store private RF data
Add exit hook so that RF drivers can free private data
Allow RF's to disable the generic TX power integration handling code
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tested by Guy Gallagher
zd1211 chip 0586:3407 v4721 high 00-13-49 AL2230_RF pa0 g---
FCC ID SI5WUB200Z
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add top-of-file comment blocks to rtl818x headers and attribute origin
of magic values to original r8187 driver.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

93cx6 datasheet available here:

        http://ww1.microchip.com/downloads/en/DeviceDoc/21749F.pdf

Figure 1-1 and Table 1-2 on pages 4-5 indicate that both Clock High
Time and Clock Low Time have largest minimum times of 450ns.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a mac80211 based wireless driver for the rtl8187 USB
wireless card.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This will add a comment for the 1us delay which is taken
after the pulse has been switched. The 1us delay is based
on the specifications so that should be made clear.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a library for reading from 93cx6 eeproms.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Woo-hoo. I'm sure somebody will report a "this doesn't compile, and
I have a new root exploit" five minutes after release, but it still
feels good ;)
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  qd65xx: fix PIO mode selection
  sis5513: adding PCI-ID

Commit 1c710c89 added the utimensat()
system call, but didn't handle the case of checking for the writability
of the target right, when the target was a file descriptor, not a
filename.

We cannot use vfs_permission(MAY_WRITE) for that case, and need to
simply check whether the file descriptor is writable.  The oops from
using the wrong function was noticed and narrowed down by Markus
Trippelsdorf.

Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: NAl Viro <viro@ftp.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a post-2.6.21 regression.

read_cache_page_async() has two invocations of mark_page_accessed() which will
launch pages right onto the active list.

Remove the first one, keeping the latter one.  This avoids marking unwanted
pages active (in the retry loop).
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NNick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PIO4 is a maximum PIO mode supported by a driver.  Using "255" as a max_mode
argument to ide_get_best_pio_mode() could result in wrong timings being used
by a driver (for "pio" equal to 5) or OOPS (for "pio" values > 5 && < 255).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Reviewed-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>

The SiS966 has one additional PCI-ID 1180.

If the chipset is using this PCI-ID, the primary channel is connected to the
first PATA-port. The secondary channel is connected to SATA-ports in IDE
emulation mode.  The legacy IO-ports are used.

The including of the PCI-ID into pata_sis is not sufficient, because the legacy
driver in drivers/ide is initialized before pata_sis.
Signed-off-by: NUwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The dependency of DLM on SYSFS got lost in
commit 6ed7257b resulting in the
following compile error with CONFIG_DLM=y, CONFIG_SYSFS=n:

<--  snip  -->

...
  LD      .tmp_vmlinux1
fs/built-in.o: In function `dlm_lockspace_init':
/home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/fs/dlm/lockspace.c:231: undefined reference to `kernel_subsys'
fs/built-in.o: In function `configfs_init':
/home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/fs/configfs/mount.c:143: undefined reference to `kernel_subsys'
make[1]: *** [.tmp_vmlinux1] Error 1

<--  snip  -->
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The printk level in this printk is bogus, as the previous printk
didn't have a terminating \n resulting in ..

Intel E7520/7320/7525 detected.<6>Disabling irq balancing and affinity

It also never printed a \n at all in the case where we didn't do
the quirk.

Change it to only make noise if it actually does something useful.
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes the following 2.6.22 regression with CONFIG_KALLSYMS=n:

<--  snip  -->

...
  CC      arch/m32r/kernel/traps.o
In file included from /home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/arch/m32r/kernel/traps.c:14:
/home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/include/linux/kallsyms.h: In function 'lookup_symbol_name':
/home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/include/linux/kallsyms.h:66: error: 'ERANGE' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/include/linux/kallsyms.h:66: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/include/linux/kallsyms.h:66: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/include/linux/kallsyms.h: In function 'lookup_symbol_attrs':
/home/bunk/linux/kernel-2.6/linux-2.6.22-rc6-mm1/include/linux/kallsyms.h:71: error: 'ERANGE' undeclared (first use in this function)
make[2]: *** [arch/m32r/kernel/traps.o] Error 1

<--  snip  -->
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When cleaning up HIDP sessions, we currently close the ACL connection
before deregistering the input device. Closing the ACL connection
schedules a workqueue to remove the associated objects from sysfs, but
the input device still refers to them -- and if the workqueue happens to
run before the input device removal, the kernel will oops when trying to
look up PHYSDEVPATH for the removed input device.

Fix this by deregistering the input device before closing the
connections.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>