Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 01 11月, 2011 1 次提交
  3. 26 7月, 2011 1 次提交
  5. 27 5月, 2011 1 次提交
  7. 24 5月, 2011 1 次提交
  9. 15 4月, 2011 1 次提交
  11. 09 3月, 2011 1 次提交
  13. 01 3月, 2011 1 次提交
  15. 23 10月, 2008 2 次提交
  17. 07 9月, 2008 2 次提交
  19. 27 4月, 2008 3 次提交
  21. 17 4月, 2008 1 次提交
  23. 09 2月, 2008 2 次提交
    • J
      uml: runtime host VMSPLIT detection · 536788fe
      由 Jeff Dike 提交于 
      Calculate TASK_SIZE at run-time by figuring out the host's VMSPLIT - this is
needed on i386 if UML is to run on hosts with varying VMSPLITs without
recompilation.

TASK_SIZE is now defined in terms of a variable, task_size.  This gets rid of
an include of pgtable.h from processor.h, which can cause include loops.

On i386, task_size is calculated early in boot by probing the address space in
a binary search to figure out where the boundary between usable and non-usable
memory is.  This tries to make sure that a page that is considered to be in
userspace is, or can be made, read-write.  I'm concerned about a system-global
VDSO page in kernel memory being hit and considered to be a userspace page.

On x86_64, task_size is just the old value of CONFIG_TOP_ADDR.

A bunch of config variable are gone now.  CONFIG_TOP_ADDR is directly replaced
by TASK_SIZE.  NEST_LEVEL is gone since the relocation of the stubs makes it
irrelevant.  All the HOST_VMSPLIT stuff is gone.  All references to these in
arch/um/Makefile are also gone.

I noticed and fixed a missing extern in os.h when adding os_get_task_size.

Note: This has been revised to fix the 32-bit UML on 64-bit host bug that
Miklos ran into.
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      536788fe
    • D
      aout: mark arches that support A.OUT format · b0b933c0
      由 David Howells 提交于 
      Mark arches that support A.OUT format by including the following in their
master Kconfig files:

	config ARCH_SUPPORTS_AOUT
		def_bool y

This should also be set if the arch provides compatibility A.OUT support for
an older arch, for instance x86_64 for i386 or sparc64 for sparc.

I've guessed at which arches don't, based on comments in the code, however I'm
sure that some of the ones I've marked as 'yes' actually should be 'no'.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      b0b933c0
  25. 04 12月, 2007 1 次提交
  27. 29 10月, 2007 1 次提交
  29. 17 10月, 2007 1 次提交
    • J
      uml: fix stub address calculations · 54ae36f2
      由 Jeff Dike 提交于 
      The calculation of CONFIG_STUB_CODE and CONFIG_STUB_DATA didn't take into
account anything but 3G/1G and 2G/2G, leaving the other vmsplits out in the
cold.

I'd rather not duplicate the four known host vmsplit cases for each of these
symbols.  I'd also like to calculate them based on the highest userspace
address.

The Kconfig language seems not to allow calculation of hex constants, so I
moved this to as-layout.h.  CONFIG_STUB_CODE, CONFIG_STUB_DATA, and
CONFIG_STUB_START are now gone.  In their place are STUB_CODE, STUB_DATA, and
STUB_START in as-layout.h.

i386 and x86_64 seem to differ as to whether an unadorned constant is an int
or a long, so I cast them to unsigned long so they can be printed
consistently.  However, they are also used in stub.S, where C types don't work
so well.  So, there are ASM_ versions of these constants for use in stub.S.  I
also ifdef-ed the non-asm-friendly portion of as-layout.h.

With this in place, most of the rest of this patch is changing CONFIG_STUB_*
to STUB_*, except in stub.S, where they are changed to ASM_STUB_*.

defconfig has the old symbols deleted.

I also print these addresses out in case there is any problem mapping them on
the host.

The two stub.S files had some trailing whitespace, so that is cleaned up here.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NJeff Dike <jdike@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      54ae36f2
  31. 31 1月, 2007 1 次提交
  33. 27 1月, 2007 1 次提交
  35. 12 10月, 2006 1 次提交
  37. 02 5月, 2006 1 次提交
  39. 27 3月, 2006 1 次提交
  41. 19 1月, 2006 1 次提交
    • P
      [PATCH] uml: arch Kconfig menu cleanups · ce2d2aed
      由 Paolo 'Blaisorblade' Giarrusso 提交于 
      *) mark as "EXPERIMENTAL" various items that either aren't very stable or
   that are actively crashing the setup of users which don't really need them
   (i.e.  HIGHMEM and 3-level pagetables on x86 - nobody needs either,
   everybody reports "I'm using it and getting trouble").

*) move net/Kconfig near to the rest of network configurations, and
   drivers/block/Kconfig near "Block layer" submenu.

*) it's useless and doesn't work well to force NETDEVICES on and to disable
   the prompt like it's done.  Better remove the attempt, and change that to a
   simple "default y if UML".

*) drop the warning about "report problems about HPPFS" - it's redundant
   anyway, as that's the usual procedure, and HPPFS users are especially
   technical (i.e.  they know reporting bugs is _good_).
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      ce2d2aed
  43. 14 11月, 2005 1 次提交
  45. 18 9月, 2005 1 次提交
  47. 05 9月, 2005 2 次提交
  49. 08 7月, 2005 1 次提交
    • J
      [PATCH] uml: skas0 - separate kernel address space on stock hosts · d67b569f
      由 Jeff Dike 提交于 
      UML has had two modes of operation - an insecure, slow mode (tt mode) in
which the kernel is mapped into every process address space which requires
no host kernel modifications, and a secure, faster mode (skas mode) in
which the UML kernel is in a separate host address space, which requires a
patch to the host kernel.

This patch implements something very close to skas mode for hosts which
don't support skas - I'm calling this skas0.  It provides the security of
the skas host patch, and some of the performance gains.

The two main things that are provided by the skas patch, /proc/mm and
PTRACE_FAULTINFO, are implemented in a way that require no host patch.

For the remote address space changing stuff (mmap, munmap, and mprotect),
we set aside two pages in the process above its stack, one of which
contains a little bit of code which can call mmap et al.

To update the address space, the system call information (system call
number and arguments) are written to the stub page above the code.  The
%esp is set to the beginning of the data, the %eip is set the the start of
the stub, and it repeatedly pops the information into its registers and
makes the system call until it sees a system call number of zero.  This is
to amortize the cost of the context switch across multiple address space
updates.

When the updates are done, it SIGSTOPs itself, and the kernel process
continues what it was doing.

For a PTRACE_FAULTINFO replacement, we set up a SIGSEGV handler in the
child, and let it handle segfaults rather than nullifying them.  The
handler is in the same page as the mmap stub.  The second page is used as
the stack.  The handler reads cr2 and err from the sigcontext, sticks them
at the base of the stack in a faultinfo struct, and SIGSTOPs itself.  The
kernel then reads the faultinfo and handles the fault.

A complication on x86_64 is that this involves resetting the registers to
the segfault values when the process is inside the kill system call.  This
breaks on x86_64 because %rcx will contain %rip because you tell SYSRET
where to return to by putting the value in %rcx.  So, this corrupts $rcx on
return from the segfault.  To work around this, I added an
arch_finish_segv, which on x86 does nothing, but which on x86_64 ptraces
the child back through the sigreturn.  This causes %rcx to be restored by
sigreturn and avoids the corruption.  Ultimately, I think I will replace
this with the trick of having it send itself a blocked signal which will be
unblocked by the sigreturn.  This will allow it to be stopped just after
the sigreturn, and PTRACE_SYSCALLed without all the back-and-forth of
PTRACE_SYSCALLing it through sigreturn.

This runs on a stock host, so theoretically (and hopefully), tt mode isn't
needed any more.  We need to make sure that this is better in every way
than tt mode, though.  I'm concerned about the speed of address space
updates and page fault handling, since they involve extra round-trips to
the child.  We can amortize the round-trip cost for large address space
updates by writing all of the operations to the data page and having the
child execute them all at the same time.  This will help fork and exec, but
not page faults, since they involve only one page.

I can't think of any way to help page faults, except to add something like
PTRACE_FAULTINFO to the host.  There is PTRACE_SIGINFO, but UML doesn't use
siginfo for SIGSEGV (or anything else) because there isn't enough
information in the siginfo struct to handle page faults (the faulting
operation type is missing).  Adding that would make PTRACE_SIGINFO a usable
equivalent to PTRACE_FAULTINFO.

As for the code itself:

- The system call stub is in arch/um/kernel/sys-$(SUBARCH)/stub.S.  It is
  put in its own section of the binary along with stub_segv_handler in
  arch/um/kernel/skas/process.c.  This is manipulated with run_syscall_stub
  in arch/um/kernel/skas/mem_user.c.  syscall_stub will execute any system
  call at all, but it's only used for mmap, munmap, and mprotect.

- The x86_64 stub calls sigreturn by hand rather than allowing the normal
  sigreturn to happen, because the normal sigreturn is a SA_RESTORER in
  UML's address space provided by libc.  Needless to say, this is not
  available in the child's address space.  Also, it does a couple of odd
  pops before that which restore the stack to the state it was in at the
  time the signal handler was called.

- There is a new field in the arch mmu_context, which is now a union.
  This is the pid to be manipulated rather than the /proc/mm file
  descriptor.  Code which deals with this now checks proc_mm to see whether
  it should use the usual skas code or the new code.

- userspace_tramp is now used to create a new host process for every UML
  process, rather than one per UML processor.  It checks proc_mm and
  ptrace_faultinfo to decide whether to map in the pages above its stack.

- start_userspace now makes CLONE_VM conditional on proc_mm since we need
  separate address spaces now.

- switch_mm_skas now just sets userspace_pid[0] to the new pid rather
  than PTRACE_SWITCH_MM.  There is an addition to userspace which updates
  its idea of the pid being manipulated each time around the loop.  This is
  important on exec, when the pid will change underneath userspace().

- The stub page has a pte, but it can't be mapped in using tlb_flush
  because it is part of tlb_flush.  This is why it's required for it to be
  mapped in by userspace_tramp.

Other random things:

- The stub section in uml.lds.S is page aligned.  This page is written
  out to the backing vm file in setup_physmem because it is mapped from
  there into user processes.

- There's some confusion with TASK_SIZE now that there are a couple of
  extra pages that the process can't use.  TASK_SIZE is considered by the
  elf code to be the usable process memory, which is reasonable, so it is
  decreased by two pages.  This confuses the definition of
  USER_PGDS_IN_LAST_PML4, making it too small because of the rounding down
  of the uneven division.  So we round it to the nearest PGDIR_SIZE rather
  than the lower one.

- I added a missing PT_SYSCALL_ARG6_OFFSET macro.

- um_mmu.h was made into a userspace-usable file.

- proc_mm and ptrace_faultinfo are globals which say whether the host
  supports these features.

- There is a bad interaction between the mm.nr_ptes check at the end of
  exit_mmap, stack randomization, and skas0.  exit_mmap will stop freeing
  pages at the PGDIR_SIZE boundary after the last vma.  If the stack isn't
  on the last page table page, the last pte page won't be freed, as it
  should be since the stub ptes are there, and exit_mmap will BUG because
  there is an unfreed page.  To get around this, TASK_SIZE is set to the
  next lowest PGDIR_SIZE boundary and mm->nr_ptes is decremented after the
  calls to init_stub_pte.  This ensures that we know the process stack (and
  all other process mappings) will be below the top page table page, and
  thus we know that mm->nr_ptes will be one too many, and can be
  decremented.

Things that need fixing:

- We may need better assurrences that the stub code is PIC.

- The stub pte is set up in init_new_context_skas.

- alloc_pgdir is probably the right place.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      d67b569f
  51. 01 5月, 2005 1 次提交
  53. 17 4月, 2005 1 次提交
    • L
      Linux-2.6.12-rc2 · 1da177e4
      由 Linus Torvalds 提交于 
      Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
      1da177e4