Memory: 124428K/131072K available (3748K kernel code, 188K rwdata,
648K rodata, 508K init, 290K bss, 6644K reserved)
Kernel virtual memory layout:
  * 0xfffdf000..0xfffff000  : fixmap
  * 0xfde00000..0xfe000000  : consistent mem
  * 0xfddf6000..0xfde00000  : early ioremap
  * 0xc9000000..0xfddf6000  : vmalloc & ioremap
SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

Today, IMMR is mapped 1:1 at startup

Mapping IMMR 1:1 is just wrong because it may overlap with another
area. On most mpc8xx boards it is OK as IMMR is set to 0xff000000
but for instance on EP88xC board, IMMR is at 0xfa200000 which
overlaps with VM ioremap area

This patch fixes the virtual address for remapping IMMR with the fixmap
regardless of the value of IMMR.

The size of IMMR area is 256kbytes (CPM at offset 0, security engine
at offset 128k) so a 512k page is enough
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NScott Wood <oss@buserror.net>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: NZhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

QE and CPM have the same muram, they use the same management
functions. Now QE support both ARM and PowerPC, it is necessary
to move QE to "driver/soc", so move the muram management functions
from cpm_common to qe_common for preparing to move QE code to "driver/soc"
Signed-off-by: NZhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Use genalloc to manage CPM/QE muram instead of rheap.
Signed-off-by: NZhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

rh_alloc() returns (unsigned long)-ERRxx on error, which may
result in overwriting memory outside the MURAM AREA.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NScott Wood <scottwood@freescale.com>

CPM muram is not cached, so use memset_io() instead of memset()
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NScott Wood <scottwood@freescale.com>

When removing prom.h include by of.h, several OF headers will no longer
be implicitly included. Add explicit includes of of_*.h as needed.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@linaro.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: linuxppc-dev@lists.ozlabs.org

Disintegrate asm/system.h for PowerPC.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
cc: linuxppc-dev@lists.ozlabs.org

With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

We need to ensure that MURAM is in a known and cleared out state before
using it as the bootloader could have utilized it from its own purposes
and left it in an unknown state.

If we don't clear it out we've seen issues with UCC ethernet:
* Multi ethernet interfaces can't work simultanously.
* Multi up/down Ethernet interfaces will halt these ports.
* UCC1 RGMII can't work when kernel boots from some hosts.
Signed-off-by: NKai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: NHongjun Chen <Hong-jun.Chen@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Several fixes as well where the +1 was missing.

Done via coccinelle scripts like:

@@
struct resource *ptr;
@@

- ptr->end - ptr->start + 1
+ resource_size(ptr)

and some grep and typing.

Mostly uncompiled, no cross-compilers.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Implement generic OF gpio hooks and thus make device-enabled GPIO chips
(i.e.  the ones that have gpio_chip->dev specified) automatically attach
to the OpenFirmware subsystem.  Which means that now we can handle I2C and
SPI GPIO chips almost* transparently.

* "Almost" because some chips still require platform data, and for these
  chips OF-glue is still needed, though with this change the glue will
  be much smaller.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
CC: linux-kernel@vger.kernel.org
CC: devicetree-discuss@lists.ozlabs.org

The OF gpio infrastructure is great for describing GPIO connections within
the device tree.  However, using a GPIO binding still requires changes to
the gpio controller just to add an of_gpio structure.  In most cases, the
gpio controller doesn't actually need any special support and the simple
OF gpio mapping function is more than sufficient.  Additional, the current
scheme of using of_gpio_chip requires a convoluted scheme to maintain
1:1 mappings between of_gpio_chip and gpio_chip instances.

If the struct of_gpio_chip data members were moved into struct gpio_chip,
then it would simplify the processing of OF gpio bindings, and it would
make it trivial to use device tree OF connections on existing gpiolib
controller drivers.

This patch eliminates the of_gpio_chip structure and moves the relevant
fields into struct gpio_chip (conditional on CONFIG_OF_GPIO).  This move
simplifies the existing code and prepares for adding automatic device tree
support to existing drivers.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

For MPC8569 CPUs we'll need to reset QE after each suspend, so make
qe_reset() code path suitable for repeated invocation, that is:

- Don't initialize rheap structures if already initialized;
- Don't allocate muram for SDMA if already allocated, just reinitialize
  registers with previously allocated muram offset;
- Remove __init attributes from qe_reset() and cpm_muram_init();
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch tweaks the way some PTE bit combinations are defined, in such a
way that the 32 and 64-bit variant become almost identical and that will
make it easier to bring in a new common pte-* file for the new variant
of the Book3-E support.

The combination of bits defining access to kernel pages are now clearly
separated from the combination used by userspace and the core VM. The
resulting generated code should remain identical unless I made a mistake.

Note: While at it, I removed a non-sensical statement related to CONFIG_KGDB
in ppc_mmu_32.c which could cause kernel mappings to be user accessible when
that option is enabled. Probably something that bitrot.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The CPM2 GPIO library code uses the non thread-safe clrbits32/setbits32
macros. This patch protects them with a spinlock.
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch implement GPIO LIB support for the CPM2 GPIOs. The code can
also be used for CPM1 GPIO port E, as both cores are compatible at the
register level.

Based on earlier work by Laurent Pinchart.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

udbg_putc is a *function pointer* that is initialized during
udbg_init_cpm. It might not be initialized properly when called from
udbg_putc_cpm(), so (recursively) call udbg_putc_cpm() directly.
Signed-off-by: NNye Liu <nyet@mrv.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is very trivial patch. We're transitioning to the cpm_muram_*
calls. That's it.

Less trivial changes:
- BD_SC_* defines were defined in the cpm.h and qe.h, so to avoid redefines
  we remove BD_SC from the qe.h and use cpm.h along with cpm_muram_*
  prototypes;
- qe_muram_dump was unused and thus removed;
- added some code to the cpm_common.c to support legacy QE bindings
  (data-only node name).
- For convenience, define qe_* calls to cpm_*. So drivers need not to be
  changed.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The kconfig entry can go away once arch/ppc and references to the config in
drivers are removed.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

A debugging printk is removed, and a comment is fixed to match
the code.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The way the current CPM binding describes available multi-user (a.k.a.
dual-ported) RAM doesn't work well when there are multiple free regions,
and it doesn't work at all if the region doesn't begin at the start of
the muram area (as the hardware needs to be programmed with offsets into
this area).  The latter situation can happen with SMC UARTs on CPM2, as its
parameter RAM is relocatable, u-boot puts it at zero, and the kernel doesn't
support moving it.

It is now described with a muram node, similar to QE.  The current CPM
binding is sufficiently recent (i.e. never appeared in an official release)
that compatibility with existing device trees is not an issue.

The code supporting the new binding is shared between cpm1 and cpm2, rather
than remain separated.  QE should be able to use this code as well, once
minor fixes are made to its device trees.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This code assumes that the ports have been previously set up, with
buffers in DPRAM.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>