add qe node to t104xqds.dtsi
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

add qe node to t104xrdb.dtsi
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

add qe node to t104xd4rdb.dtsi and t1040si-post.dtsi.
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Now that the FMAN mac driver has been merged the fman node is relevant.

The kmcoge4 board implements 3 ethernet interfaces, 1 with a RGMII phy
and 2 with fixed 1 Giga SGMII links.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Add support for the Artesyn MVME7100 Single Board Computer.

The MVME7100 is a 6U form factor VME64 computer with:

    - A two e600 cores Freescale MPC8641D CPU
    - 2 GB of DDR2 onboard memory
    - Four Gigabit Ethernets
    - Five 16550 compatible UARTs
    - One USB 2.0 port
    - Two PCI/PCI eXpress Mezzanine Card (PMC/XMC) Slots
    - A DS1375 Real Time Clock (RTC)
    - 512 KB of Non-Volatile Memory (NVRAM)
    - Two 64 KB EEPROMs
    - 128 MB NOR and 4/8 GB NAND Flash

This patch is based on linux-4.7-rc1 and has been only boot tested.

Limitations:
    This patch covers only models 171 and 173
    No plans to support CPLD timers

Know issues:
    All four PHYs work in polling mode

Configuration is missing for:
    PCI IDSEL and PCI Interrupt definition

Support is missing for:
    Cache and memory controllers (which are very similar to the 85xx ones
        but right now I don't know if we can re-use their support)
    Watchdog, USB, NVRAM, NOR, NAND, EEPROMs, VME, PMC/XMC and RTC
Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

Add usb aliases for consistency with the other platforms.
Signed-off-by: NLaurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: NSriram Dash <sriram.dash@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Change USB controller version name to 2.5 in compatible string for T1040
Signed-off-by: NSriram Dash <sriram.dash@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

This patch adds an OPAL console backend to the powerpc boot wrapper so
that decompression failures inside the wrapper can be reported to the
user. This is important since it typically indicates data corruption in
the firmware and other nasty things.

Currently this only works when building a little endian kernel. When
compiling a 64 bit BE kernel the wrapper is always build 32 bit to be
compatible with some 32 bit firmwares. BE support will be added at a
later date. Another limitation of this is that only the "raw" type of
OPAL console is supported, however machines that provide a hvsi console
also provide a raw console so this is not an issue in practice.
Actually-written-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NOliver O'Halloran <oohall@gmail.com>
[mpe: Move #ifdef __powerpc64__ to avoid warnings on 32-bit]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fix PCI interrupt map definition from 2 to 4 cells. Move
interrupt-map and interrupt-map-mask and clone interrupts
into the pcie child nodes.
Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

Commit dc37374b ("powerpc/fsl: Move Freescale device tree files
into fsl folder") moved a lot of device tree files into fsl directory,
fixing Makefile for cuImage target only.  Unfortunately there are other
targets which require embedding a device tree into the kernel image
(e.g. dtbImage.%).  So use a more generic approach.
Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
[scottwood: cleaned up commit message]
Signed-off-by: NScott Wood <oss@buserror.net>

For T1040, T1042, T1023, and T1024, they should use the compatible
string "fsl,qoriq-rcpm-2.1".
Signed-off-by: NChenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

On the t208xrdb and t1040rdb, the SPI device is n25q512ax3
instead of n25q512a.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@freescale.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Device tree update for the Applied micro processor 460ex on-chip SATA to use
"dmas" property.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Starting with commit <8947e396> ("Documentation: dt: mtd:
replace "nor-jedec" binding with "jedec, spi-nor"") we have
"jedec,spi-nor" binding indicating support for JEDEC identification.

Use it for all flashes that are supposed to support READ ID op
according to the datasheets.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@freescale.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

This patch adds pcsphy node to FManV3 device tree.
Signed-off-by: NIgal Liberman <igal.liberman@freescale.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Describe the PHY topology for all configurations supported by each board

Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: NShruti Kanetkar <Shruti@freescale.com>
Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: NIgal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

Avoid duplication of the interrupt-parent, migrate to 4 interrupt-cells
and set the right clock-frequency for pcie (100 Mhz).
Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NAlessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: NScott Wood <oss@buserror.net>

add the missing RAID Engine device node for p5040.
otherwise, the device can not be detected.
Signed-off-by: NXuelin Shi <xuelin.shi@nxp.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Signed-off-by: NAdam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Also add nodes and properties for thermal management support. Meanwhile
preprocessor support is needed using thermal of framework.
Signed-off-by: NJia Hongtao <hongtao.jia@freescale.com>
Reviewed-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Also add nodes and properties for thermal management support. Meanwhile
preprocessor support is needed using thermal of framework.
Signed-off-by: NJia Hongtao <hongtao.jia@freescale.com>
Reviewed-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

p1010rdb uses the irq[4:5] for inta and intb to pcie,
it is active-high, so set it.
Signed-off-by: NZhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

FMan V3H has 2 different MURAM sizes:
    In B4860/4420 the MURAM size is 512KB.
    In T4240 and T2080 the MURAM size is 384KB.

The MURAM size in FMan V3H device tree is 384KB.
This patch updates the MURAM size for B4 to 512KB.
Signed-off-by: NIgal Liberman <igal.liberman@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Signed-off-by: NHarninder Rai <harninder.rai@freescale.com>
Signed-off-by: NMinghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: NHou Zhiqiang <B48286@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

All users of QPACE have upgraded to QPACE2 so remove the Cell QPACE code.
Signed-off-by: NRashmica Gupta <rashmicy@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This file was originally cloned off of the MPC8641D-HPCN reference
platform, which actually had a PHY IRQ line connected. However this
board does not. The bogus entry was largely inert and went undetected
until commit 321beec5 ("net: phy: Use
interrupts when available in NOLINK state") was added to the tree.

With the above commit, the board fails to NFS boot since it sits waiting
for a PHY IRQ event that of course never arrives. Removing the bogus
entries from the DTS file fixes the issue.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

if the language is not english objdump output is not parsed correctly
and format is "". Later, "ld -m $format" fails.

This patch adds "LANG=C" to force english output for objdump.
Signed-off-by: NLaurent Vivier <laurent@vivier.eu>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: NShruti Kanetkar <Shruti@freescale.com>
Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: NIgal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: NShruti Kanetkar <Shruti@freescale.com>
Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: NIgal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

This allows new-style clock references to be used, which is needed for
fman.  The old clock nodes will be removed and all clock references
converted to new-style once the qoriq-cpufreq driver is updated to stop
depending on the old-style references in cpu nodes.
Signed-off-by: NScott Wood <scottwood@freescale.com>

Add a device tree binding for Freescale MPC512x LocalPlus Bus FIFO and
introduce the document describing that binding.
Signed-off-by: NAlexander Popov <alex.popov@linux.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Add a boot wrapper script function run_cmd which will run a shell command
quietly and only print the output if either V=1 or an error occurs.

Also, run the ps3 dd commands with run_cmd to clean up the build output.
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

To make provision for more than one L2 caches in the system, change the
name from L2 to L2_1; same as in T4 platforms.
* Also remove the L2 entry from common file
  "arch/powerpc/boot/dts/fsl/b4si-post.dtsi"
  Keep them only in separate files for b4860 and b4420.
Signed-off-by: NShaveta Leekha <shaveta@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

It makes no sense that some Freescale device tree files are in fsl
directory while some others not. This patch move Freescale device tree
files into fsl folder. To do that the following two steps are made:
- Move Freescale device tree files into fsl folder.
- Update the include path in these files from "fsl/*.dtsi" to "*.dtsi".

Please add "fsl/" prefix when you make dtb using Makefile.
Signed-off-by: NJia Hongtao <hongtao.jia@freescale.com>
[scottwood: fixed cuImage rule]
Signed-off-by: NScott Wood <scottwood@freescale.com>

In case of B4860 LIODN register for sRIO is not in GUTs block but in
the sRIO register space.
Signed-off-by: NVarun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

This board uses a P5020 chip, and boots just fine using
the corenet_generic code. The device tree is very similar to the
P5020DS, except that there is no Flash memory. The environment is,
instead, stored on an MMC card on the motherboard.
Signed-off-by: NAndy Fleming <afleming@gmail.com>
[scottwood: fixed trailing whitespace]
Signed-off-by: NScott Wood <scottwood@freescale.com>