This patch fixes lockdep issue due to circular locking dependency of
struct_mutex, i_mutex_key, mmap_sem, relay_channels_mutex.
For GuC log relay channel we create debugfs file that requires i_mutex_key
lock and we are doing that under struct_mutex. So we introduced newer
dependency as:
    &dev->struct_mutex --> &sb->s_type->i_mutex_key#3 --> &mm->mmap_sem
However, there is dependency from mmap_sem to struct_mutex. Hence we
separate the relay create/destroy operation from under struct_mutex.
Also added runtime check of relay buffer status.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

======================================================
WARNING: possible circular locking dependency detected
4.15.0-rc6-CI-Patchwork_7614+ #1 Not tainted
------------------------------------------------------
debugfs_test/1388 is trying to acquire lock:
 (&dev->struct_mutex){+.+.}, at: [<00000000d5e1d915>] i915_mutex_lock_interruptible+0x47/0x130 [i915]

but task is already holding lock:
 (&mm->mmap_sem){++++}, at: [<0000000029a9c131>] __do_page_fault+0x106/0x560

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #3 (&mm->mmap_sem){++++}:
       _copy_to_user+0x1e/0x70
       filldir+0x8c/0xf0
       dcache_readdir+0xeb/0x160
       iterate_dir+0xdc/0x140
       SyS_getdents+0xa0/0x130
       entry_SYSCALL_64_fastpath+0x1c/0x89

-> #2 (&sb->s_type->i_mutex_key#3){++++}:
       start_creating+0x59/0x110
       __debugfs_create_file+0x2e/0xe0
       relay_create_buf_file+0x62/0x80
       relay_late_setup_files+0x84/0x250
       guc_log_late_setup+0x4f/0x110 [i915]
       i915_guc_log_register+0x32/0x40 [i915]
       i915_driver_load+0x7b6/0x1720 [i915]
       i915_pci_probe+0x2e/0x90 [i915]
       pci_device_probe+0x9c/0x120
       driver_probe_device+0x2a3/0x480
       __driver_attach+0xd9/0xe0
       bus_for_each_dev+0x57/0x90
       bus_add_driver+0x168/0x260
       driver_register+0x52/0xc0
       do_one_initcall+0x39/0x150
       do_init_module+0x56/0x1ef
       load_module+0x231c/0x2d70
       SyS_finit_module+0xa5/0xe0
       entry_SYSCALL_64_fastpath+0x1c/0x89

-> #1 (relay_channels_mutex){+.+.}:
       relay_open+0x12c/0x2b0
       intel_guc_log_runtime_create+0xab/0x230 [i915]
       intel_guc_init+0x81/0x120 [i915]
       intel_uc_init+0x29/0xa0 [i915]
       i915_gem_init+0x182/0x530 [i915]
       i915_driver_load+0xaa9/0x1720 [i915]
       i915_pci_probe+0x2e/0x90 [i915]
       pci_device_probe+0x9c/0x120
       driver_probe_device+0x2a3/0x480
       __driver_attach+0xd9/0xe0
       bus_for_each_dev+0x57/0x90
       bus_add_driver+0x168/0x260
       driver_register+0x52/0xc0
       do_one_initcall+0x39/0x150
       do_init_module+0x56/0x1ef
       load_module+0x231c/0x2d70
       SyS_finit_module+0xa5/0xe0
       entry_SYSCALL_64_fastpath+0x1c/0x89

-> #0 (&dev->struct_mutex){+.+.}:
       __mutex_lock+0x81/0x9b0
       i915_mutex_lock_interruptible+0x47/0x130 [i915]
       i915_gem_fault+0x201/0x790 [i915]
       __do_fault+0x15/0x70
       __handle_mm_fault+0x677/0xdc0
       handle_mm_fault+0x14f/0x2f0
       __do_page_fault+0x2d1/0x560
       page_fault+0x4c/0x60

other info that might help us debug this:

Chain exists of:
  &dev->struct_mutex --> &sb->s_type->i_mutex_key#3 --> &mm->mmap_sem

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&mm->mmap_sem);
                               lock(&sb->s_type->i_mutex_key#3);
                               lock(&mm->mmap_sem);
  lock(&dev->struct_mutex);

 *** DEADLOCK ***

1 lock held by debugfs_test/1388:
 #0:  (&mm->mmap_sem){++++}, at: [<0000000029a9c131>] __do_page_fault+0x106/0x560

stack backtrace:
CPU: 2 PID: 1388 Comm: debugfs_test Not tainted 4.15.0-rc6-CI-Patchwork_7614+ #1
Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./J4205-ITX, BIOS P1.10 09/29/2016
Call Trace:
 dump_stack+0x5f/0x86
 print_circular_bug.isra.18+0x1d0/0x2c0
 __lock_acquire+0x14ae/0x1b60
 ? lock_acquire+0xaf/0x200
 lock_acquire+0xaf/0x200
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 __mutex_lock+0x81/0x9b0
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? i915_mutex_lock_interruptible+0x47/0x130 [i915]
 i915_mutex_lock_interruptible+0x47/0x130 [i915]
 ? __pm_runtime_resume+0x4f/0x80
 i915_gem_fault+0x201/0x790 [i915]
 __do_fault+0x15/0x70
 ? _raw_spin_unlock+0x29/0x40
 __handle_mm_fault+0x677/0xdc0
 handle_mm_fault+0x14f/0x2f0
 __do_page_fault+0x2d1/0x560
 ? page_fault+0x36/0x60
 page_fault+0x4c/0x60

v2: Added lock protection to guc->log.runtime.relay_chan (Chris)
    Fixed locking inside guc_flush_logs uncovered by new lockdep.

v3: Locking guc_read_update_log_buffer entirely with relay_lock. (Chris)
    Prepared intel_guc_init_early. Moved relay_lock inside relay_create
    relay_destroy, relay_file_create, guc_read_update_log_buffer. (Michal)
    Removed struct_mutex lock around guc_log_flush and removed usage
    of guc_log_has_relay() from runtime_create path as it needs
    struct_mutex lock.

v4: Handle NULL relay sub buffer pointer earlier in read_update_log_buffer
    (Chris). Fixed comment suffix **/. (Michal)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104693
Testcase: igt/debugfs_test/read_all_entries # with enable_guc=1 and guc_log_level=1
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-3-git-send-email-sagar.a.kamble@intel.com

GuC log streaming needs interrupts enabled prior to GuC resume but
runtime pm interrupt setup was happening post GuC resume. Fix it.
While at it, fix the unwinding of steps in the runtime suspend path.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104695Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-2-git-send-email-sagar.a.kamble@intel.com

Disabling GuC interrupts involves access to GuC IRQ control registers
hence ensure device is RPM awake.

v1-v2: old changelog
1: Add comment about need to synchronize flush work and log runtime
   destroy
2: Moved patch earlier in the series and removed comment about future
work. (Tvrtko)

v3: Added assert_rpm_wakelock_held() to gen9_*_guc_interrupts. (Chris)
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1516808821-3638-1-git-send-email-sagar.a.kamble@intel.com

Let's document why we claim hsub==8,vsub==16 for CCS.

v2: Replace my explanation with Jason's

Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119144152.17224-1-ville.syrjala@linux.intel.comReviewed-by: NJason Ekstrand <jason@jlekstrand.net>

Apparently SKL/KBL/CFL need some manual help to get the
programmed HDMI vswing to stick. Implement the relevant
workaround (display w/a #1143).

Note that the relevant chicken bits live in a transcoder register
even though the bits affect a specific DDI port rather than a
specific transcoder. Hence we must pick the correct transcoder
register instance based on the port rather than based on the
cpu_transcoder.

Also note that for completeness I included support for DDI A/E
in the code even though we never have HDMI on those ports.

v2: CFL needs the w/a as well (Rodrigo and Art)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122174131.28046-1-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Replace the ad-hoc plane indexing scheme used by the frontbuffer
tracking with enum plane_id.

The old video overlay not being part of the plane_id namespace
will just be given the high bit.

v2: Drop the unintended whitespace change (Chris)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123183343.9181-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

When we finally decide the gpu is idle, that is a good time to shrink
our kmem_caches.

v3: Defer until an rcu grace period after we idle.
v4: Think about epoch wraparound and how likely that is.
v5: Use I915_EPOCH_INVALID magic.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124113608.14909-2-chris@chris-wilson.co.uk

By counting the number of times we have woken up, we have a very simple
means of defining an epoch, which will come in handy if we want to
perform deferred tasks at the end of an epoch (i.e. while we are going
to sleep) without imposing on the next activity cycle.

v2: No reason to specify precise number of bits here.
v3: Take Tvrtko's advice and reserve 0 as an invalid epoch.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124113608.14909-1-chris@chris-wilson.co.uk

We only use the preempt context to inject an idle point into execlists.
We never need to reference its logical state, so tell the GPU never to
load it or save it.

v2: BIT(2) for save-inhibit.

N.B. Daniele mentioned this bit mbz for ICL, and has been moved into the
submission process rather than the context image.
Suggested-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123210412.17653-1-chris@chris-wilson.co.uk

Newer platforms may have subtle offset changes, which will increase the
number of defines, so it is probably better to start moving them to its
own header file. Also move the macros used while setting the reg state.

v2: Rename to intel_lrc_reg.h, to be consistent with i915_reg.h and
intel_guc_reg.h (Chris)
v3: License notice shenanigans.
v4: Documentation/process/coding-style.rst is always right (Chris)
v5: Rebase.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124004349.22126-2-michel.thierry@intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The macros we use to init the reg_state had the following issues reported
by checkpatch --strict.

  Macro argument reuse 'reg_state' - possible side-effects
  Macro argument reuse 'pos' - possible side-effects
  Macro argument reuse 'ppgtt' - possible side-effects
  spaces preferred around that '+' (ctx:VxV)

So fix these issues before they are moved to a new header file.
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180124004349.22126-1-michel.thierry@intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

We need to generate the event config value using the uAPI class and not
the driver internal one.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 109ec558 ("drm/i915/pmu: Only enumerate available counters in sysfs")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123134558.3222-1-tvrtko.ursulin@linux.intel.com

Current code always select _CNL_AUX_ANAOVRD1_B
register regardless the pw in use.

CNL_DISP_PW_AUX_B = 9
CNL_DISP_PW_AUX_C = 10
CNL_DISP_PW_AUX_D = 11

And for pick we want

B = 0
C = 1
D = 2

Fixes: ddd39e4b ("drm/i915/cnl: apply Display WA #1178 to fix type C dongles")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123215245.24026-1-rodrigo.vivi@intel.com

Let's ignore VBT request if the pin is clearly wrong.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104139
Cc: Kai Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123174050.4261-1-rodrigo.vivi@intel.comReviewed-by: NRadhakrishna Sripada <radhakrishna.sripada@intel.com>

Now that we can read the CSB from the HWSP, we may avoid having to
perform mmio reads entirely and so forgo the rigmarole of the forcewake
dance.

v2: Include forcewake hint for GEM_TRACE readback of mmio. If we don't
hold fw ourselves, the reads may return garbage.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122100714.15137-1-chris@chris-wilson.co.uk

On gen9+, after an idle period the HW will disable the entire power well
to conserve power (by preventing current leakage). It takes around a 100
microseconds to bring the power well back online afterwards. With the
current hysteresis value of 25us (really 25 * 1280ns), we do not have
sufficient time to respond to an interrupt and schedule the next execution
before the HW powers itself down. (At present, we prevent this by
grabbing the forcewake for prolonged periods of time, but that overkill
fixed in the next patch.) The minimum we want to set the power gating
hysteresis to is the length of time it takes us to service the GPU, which
across a broad spectrum of machines is about 250us.

(Note this also brings guc latency into the same ballpark as execlists.)

v2: Include some notes on where I plucked the numbers from.

Testcase: igt/gem_exec_nop/sequential
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Reviewed-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122135541.32222-1-chris@chris-wilson.co.uk

We fail engine initialization if the scratch VMA cannot be created so
there is no point in error handle it later. If the initialization ordering
gets messed up, we can explode during development just as well.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119100005.9072-2-tvrtko.ursulin@linux.intel.com

Render engine constructor helpers must only be called from the render
engine constructors, but there is no need to burden the production
binaries with warnings which can only be triggered during development.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119100005.9072-1-tvrtko.ursulin@linux.intel.com

In case of eDP because the panel has a fixed mode, the link rate
and lane count at which it is trained corresponds to the link BW
required to support the native resolution of the panel. In case of
panles with lower resolutions where fewer lanes are hooked up internally,
that number is reflected in the MAX_LANE_COUNT DPCD register of the panel.
So it is pointless to fallback to lower link rate/lane count in case
of link training failure on eDP connector since the lower link BW
will not support the native resolution of the panel and we cannot
prune the preferred mode on the eDP connector.

In case of Link training failure on the eDP panel, something is wrong
in the HW internally and hence driver errors out with a loud
and clear DRM_ERROR message.

v2:
* Fix the DEBUG_ERROR and add {} in else (Ville Syrjala)

Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=103369Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507835618-23051-1-git-send-email-manasi.d.navare@intel.com

As we attempt to allocate pages for use in a new WC stash, direct
reclaim may run underneath us and fill up the WC stash. We have to be
careful then not to overflow the pvec.

Fixes: 66df1014 ("drm/i915: Keep a small stash of preallocated WC pages")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103109Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180121173143.17090-1-chris@chris-wilson.co.uk

Avoids some typo pitfalls.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171220201021.17619-1-dhinakaran.pandiyan@intel.com

If we fail to allocate a new request, make sure we recover the pages
that are in the process of being freed by inserting an RCU barrier.

v2: Comment before the shrink and barrier in the error path.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119144657.22606-1-chris@chris-wilson.co.uk

It looks that GuC log functionality is not fully functional yet and
causes issues when enabled by auto(-1) modparam on debug builds.
For example, but not limited to:

[   30.062893] ======================================================
[   30.062894] WARNING: possible circular locking dependency detected
[   30.062895] 4.15.0-rc8-CI-CI_DRM_3648+ #1 Tainted: G     U
[   30.062896] ------------------------------------------------------
[   30.062897] debugfs_test/1268 is trying to acquire lock:
[   30.062898]  (&dev->struct_mutex){+.+.}, at: [<00000000e4213449>] i915_mutex_lock_interruptible+0x47/0x130 [i915]
[   30.062921]
               but task is already holding lock:
[   30.062921]  (&mm->mmap_sem){++++}, at: [<00000000dd7adc93>] __do_page_fault+0x106/0x560
[   30.062924]
               which lock already depends on the new lock.

References: 0ed87953 ("drm/i915/guc: Redefine guc_log_level modparam values")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104693
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104694
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104695Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119124926.29844-1-michal.wajdeczko@intel.comReviewed-by: NMichal Winiarski <michal.winiarski@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Gen11 removes the Resource Streamer, which frees up a big chunk of
the context image. BSpec indicates 12544 DWORDs (13 pages), plus
one page for PPHWSP.

Please notice that, when looking at the BSpec context image table,
the right filter has to be applied as some rows are excluded for
specific GENs. Also, some rows apply per-subslice (for the
calculation above, we have supposed I915_MAX_SUBSLICES = 8).

v2: Rebase.
v3: Use the right size as per the BSpec.
v4:
  - Rebased on top of the default context size (Rodrigo)
  - Clarify in the commit message where the subslice calculation
    comes from.
v5: s/12538/12544/ (Daniele)

BSpec: 18907

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com> (older version)
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515711307-28979-2-git-send-email-oscar.mateo@intel.com

Instead of returning whatever size the latest GEN used. This is because
context sizes for new GENs can go up or down, but the only safe thing to
do for missing cases is to use the largest known one, whatever that is.
Suggested-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515711307-28979-1-git-send-email-oscar.mateo@intel.com

MMIO addresses and register definition for the new interrupt
registers in Gen11.

v2: Removed spelt out VCS and VECS bit definitions. (Daniel Vetter)
v3: Adjust VCS and VECS. (Daniele Ceraolo Spurio)
v4: Bikeshedding (Paulo).

Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109232336.11029-5-paulo.r.zanoni@intel.com

Add the PCI ID for the ICL PCH - ICP.

v2: rebased.
v3: rebased.
v4: fix ICP name.
v5: fix the ID mask (Fei Li).
v6 (from Paulo): bikesheds.

Cc: Li, Fei <fei.li@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-9-paulo.r.zanoni@intel.com

In ICP, there are three TC ports and 3 DDI ports.

v2:
 - Correct Pin mapping.
v3:
 - Update pin mapping into per platform implementation
   rather than previous approach of port wise mapping.
v4:
 - Update GMBUS_NUM_PINS (Paulo)
v5:
 - rebase.
v6:
 - Update function name, GMBUS_PIN_NUM (Paulo)
v7 (from Paulo):
 - Make it apply.
v8 (from Paulo):
 - Maintain consistent if ladder ordering.

Suggested by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-8-paulo.r.zanoni@intel.com

ICP has two backlight controllers - similar to previous platforms like
BXT -, but we only use one controller for now, so we can just reuse
the CNP code.

v2: Remove the usage of ICP_SECOND_PPS_BACKLIGHT register.(Jani)
Reuse CNP code since it is very similar.(Ville)
v3 (from Paulo): Rebase.
v4 (from Paulo): adjust commit message (James) and comment (Rodrigo).

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: NJames Ausmus <james.ausmus@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119184812.2888-1-paulo.r.zanoni@intel.comSigned-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

ICP, like BXT, has has two panel power sequencers.

v2: Simplify the code. Remove unwanted register definitions.
Make code as close to BXT style as possible. (Ville)
Also, remove the use of ICP_SECOND_PPS_BACKLIGHT for now.
Moving forward, if we are sure we need to set this register,
we can access it.

v3: Use INTEL_GEN(dev_priv), make code more readeable. (Ville)

v4 (from Paulo):
 - Coding style fixes.
 - Add a missing HAS_PCH_CNP -> gen10+ check.
 - Rebase.

v5: Use per platform checks rather than INTEL_GEN().
    v4 of this patch breaks on CoffeeLake, since CFL uses
    CNP and per platform check makes sense in that case.

v6 (from Paulo):
 - v5 was a patch on top of v4, not a new version. Now v6 is correctly
   a new version of the original patch.

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-6-paulo.r.zanoni@intel.com

Add register definitions for setting the rawclock.
Set the numerator,denominator and divider values.

v2: Simplify the commit message. Simplify the math.
Add  register bits for numerator. (Paulo)
v3 (from Paulo): coding style bikesheds.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-5-paulo.r.zanoni@intel.com

Add the enum additions to ICP PCH.

v2 (from Paulo): don't set any platforms to it yet since ICP support is
incomplete.
v3 (from Rodrigo): Fix ICP name.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-4-paulo.r.zanoni@intel.com

Icelake is an Intel® Processor containing an Intel® Graphics
Controller.

This is just an initial Icelake definition. PCI IDs, Icelake support
and new features coming in following patches.

v2: Add .ddb_size and .has_guc (Michal Wajdeczko).
v3: Add the ICL_FEATURES macro (Kelvin Gardiner).
v4 (from Paulo): Add missing __initconst (Paulo) and say "graphics
controller" instead of something that looks like an official marketing
name but isn't (Chris).
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-3-paulo.r.zanoni@intel.com

Some Cannonlake SKUs will come with a full split between
port A and port E. This will be called port F although it
is not a 6th port, but only a split.

Note this patch alone is not sufficient for port F enabling,
it's just the first step.

v2: Fix size of dvo_ports found by Ander.
v3: Adding missing cases from intel_bios.c for Port_F
v4: Adding other missing cases and fix the commit message.
v5: Rebase on top of display headers rework.
v6 (from Paulo): improve commit message, bikeshed bit definitions.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111180010.24357-2-paulo.r.zanoni@intel.com

We may have fused or unused pipes in our system. Let's check that the pipe
in question is within limits of accessible pipes. In case, that we are not
able to access the pipe, we return early with a warning.

v2: Rephrasing of the commit message (Jani)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103206Reported-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJaswinder Singh Rajput <jaswinder@perfectintelligent.com>
Suggested-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1513584243-12607-1-git-send-email-mika.kahola@intel.com

SKL+ "sprites" no longer have 16KB max stride limit that earlier
platforms had. Bump up the limit to 32KB.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-7-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Allow sprites to scan out compressed framebuffers.

Since different platforms have a different set of planes that
support CCS let's add a small helper to determine whether a
specific plane supports CCS or not. Currently that information
is spread around in many places, and not all the pieces of
code even agree with each other.

In addition to allowing sprites to scan out compressed fbs,
the other fix here is that we stop rejecting them on pipe C
on CNL.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-6-ville.syrjala@linux.intel.comReviewed-by: NMika Kahola <mika.kahola@intel.com>

Split the g4x and snb cases into separate functions to match how we deal
with all other platforms. Also sort the switch cases to match the format
lists we've declared earlier, to ease comparisons.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-5-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Y/Yf were dropped out from the SKL+ sprite modifier list on account
of some watermark issues Daniel Stone was having. My subsequent testing
seemed to indicate that things work better now, so add the modifiers
back in.

v2: Update the commit message with a better explanation

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-4-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The unreachable() is very much unreachable and the compiler knows
that, so there's no point in having it.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171222192231.17981-3-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>