Pull control is availalbe for WM8994 AIF2, generally disabled as part of
the GPIO configuration in order to save power after system startup. As on
newer devices in the series there is no GPIO functionality on these pins
this will happen less naturally so have the driver disable the pulls as the
AIF is probed.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

On WM8994 class devices only the analogue portions of the CODEC require
VMID so when running digital only paths we can leave VMID disabled.
On some earlier devices the FLL uses VMID so we don't use DAPM reference
counting alone, we maintain an internal reference count which is also
enabled and disabled by the FLL startup.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Currently this does not actually do anything, it is being introduced in
order to facilitate additional power optimisations for current generation
devices.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

This error would have no effect on current silicon revisions, the fall
through case has the same behaviour.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Some devices can have performance optimized by setting different offsets
for left and right channels.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Later WM8994 devices implement a new DC servo readback mode with the
register used to access the offset moved to register 0x59. Implement
support for this and enable it on the appropriate devices.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The WM8994 and WM8958 series of devices have two MICBIAS supplies rather
than one, the current widget actually manages the microphone detection
control register bit (which is managed separately by the relevant API).

Fix this, hooking the relevant supplies up to the MICBIAS1 and MICBIAS2
widgets.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

If DAIs are idle but their clocks are in use for some reason (eg, as
SYSCLK or for accessory detect) then set the clock dividers to the maximum
to reduce slightly the power consumption of the unclocked circuits.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Try the completion before we start the FLL so that if an interrupt was
delayed long enough for us to miss it we don't wait for the completion
it signalled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

We should spot them anyway on state changes but logging them gives us
better time information about when the misconfiguration happened.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We can have valid but very low clocks in accessory detection modes.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If we have interrupts then wait for the FLL lock interrupt rather than
using dead reckoning when waiting for the FLL to start.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This ensures appropriate clocking for bypass paths to speaker and
headphone and direct voice paths on affected revisions.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Future devices will not benefit from this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

This delay is very conservative.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

Allowing the two to be used independently.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Commit fafd2176 ("ASoC: Store a list of widgets in a DAPM mux/mixer kcontrol")
changed the control private data type that is passed to snd_soc_cnew when
creating dapm mixer and mux controls. Commit did not update a few codec
drivers that are using their own put callbacks and thus are accessing a
wrong data type.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It will be non-functional with the basises and clocks off anyway, if the
system needs microphone detection enabled over suspend then it should be
causing the CODEC to ignore suspend using the APIs for that to prevent
the biases being disabled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Ensures that we apply volume updates that don't affect the right channel.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

DSP2 in the WM8958 can be used to support an upgraded EQ for use in
demanding applications.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

With appropriate firmware the WM8958 can support Virtual Surround Sound or
VSS, widening the stereo audio image for improved user experience. Enable
support for this mode of operation when the appropriate firmware can be
loaded at runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Allow userspace to supply an update to the ROM firmware. The firmware
request is non-blocking so userspace can load the firmware at its
leisure without delaying startup, the driver will begin using the
firmware the next time MBC is started after it has been supplied.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The DSP2 startup requires that the clock be enable so if we've deferred
clock startup we need to defer DSP2 startup
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

DSP2 on the WM8958 has a default ROM which provides a multi-band
compressor for enhanced performance on mobile devices but can also
support runtime download of alternative firmware. In preparation for
more exploiting this functionality refactor the code to split the
handling of DSP2 into a separate file.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The first WM8958 revision requires similar treatment.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Without this fix the driver won't instantiate properly on relevant
devices.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

Without this fix the driver won't instantiate properly on relevant
devices.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The patch 'ASoC: WM8994: Improve Playback Robustness' did not handle
this case properly.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure that the ADCs are provided with a clock as the previous patch
"ASoC: WM8994: Improve playback robustness" did not handle this case
properly.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Since we began using the late clock disable functionality, ensure that
we don't disable the clock if any of the ADC or DAC paths are still
enabled.  This happens when we have simultaneous playback and recording.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The default WM8958 jack detection handler implements a full set of buttons
and also support for video detection. Support for multi-button jacks is
fairly system specific and will usually require some tuning for headsets
so simplify the implementation to only report a simple short to ground
button, leaving multi-button headsets to be handled by system specific
code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The WM8958 has a different microphone bias architecture to WM8994 so needs
different configuration to WM8994. Support this in platform data.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Allow direct routing of the WM8958 microphone detection signal to a GPIO
to be used, saving the need to demux the interrupt.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>