- 30 3月, 2015 5 次提交
-
-
由 Liu Ying 提交于
The MIPI DSI node contains some ports which represent possible DRM CRTCs it can connect with. Each port has a 'reg' property embedded. This property will be wrongly interpretted by the MIPI DSI bus driver, because the driver will take each subnode which contains a 'reg' property as a DSI peripheral device. This patch moves the existing MIPI DSI ports into a new 'ports' node so that the MIPI DSI bus driver may distinguish its DSI peripheral device(s) from the existing ports. Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NLiu Ying <Ying.Liu@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Peter Chen 提交于
Since imx6sx-sdb reva board is experimental and will not be used formally (eg, no software release based on it), we set revb board as the formal imx6sx-sdb board. The imx6sx-sdb uses pfuse200 as pmic which has only one power supply for both VDDARM_IN and VDDSOC_IN, so VDDARM_IN and VDDSOC_IN have to use the same (higher one in the same frequency) one as its power supply, that's the reason we override the OPP setting in board dts file. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Peter Chen 提交于
The imx6sx sdb board has two revisions, the current mainline one is reva which is experimental and mainly for internal use. In this commit, we rename imx6sx-sdb.dts to imx6sx-sdb.dtsi, and move the reva dedicated contents to imx6sx-sdb-reva.dts. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Bhuvanchandra DV 提交于
MCP2515 CAN controller is available on Colibri Evaluation board. Hence enable MCP2515 CAN. Acked-by: NStefan Agner <stefan@agner.ch> Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Bhuvanchandra DV 提交于
Signed-off-by: NBhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: NStefan Agner <stefan@agner.ch> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 17 2月, 2015 3 次提交
-
-
由 Arnaud Ebalard 提交于
"isil" and "isl" prefixes are used at various locations inside the kernel to reference Intersil corporation. This patch is part of a series fixing those locations were "isl" is used in compatible strings to use the now expected "isil" prefix instead (NASDAQ symbol for Intersil and most used version). Note: isl9305 is an I2C device so the patch does not in fact currently depend on the introduction of "isil"-based compatible string in isl9305 driver (provided by another patch) because I2C core does not check the prefix yet. Signed-off-by: NArnaud Ebalard <arno@natisbad.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darshana Padmadas <darshanapadmadas@gmail.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Ray Jui 提交于
Add I2C device nodes and its properties in bcm-cygnus.dtsi but keep them disabled there. Individual I2C devices can be enabled in board specific dts file when I2C slave devices are enabled in the future Signed-off-by: NRay Jui <rjui@broadcom.com> Reviewed-by: NScott Branden <sbranden@broadcom.com> Reviewed-by: NKevin Cernekee <cernekee@chromium.org> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
由 Florian Fainelli 提交于
The L2 cache properties were completely off with respect to what the hardware is configured for. Fix the cache-size, cache-line-size and cache-sets to reflect the L2 cache controller we have: 512KB, 16 ways and 32 bytes per cache-line. Fixes: 46d4bca0 ("ARM: BCM63XX: add BCM63138 minimal Device Tree") Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
-
- 14 2月, 2015 2 次提交
-
-
由 Gregory CLEMENT 提交于
The Marvell Armada 38x SoCs contains an RTC which differs from the RTC used in the other mvebu SoCs until now. This commit adds the Device Tree description of this interface at the SoC level. Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Arnaud Ebalard <arno@natisbad.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Boris BREZILLON <boris.brezillon@free-electrons.com> Cc: Lior Amsalem <alior@marvell.com> Cc: Tawfik Bayouk <tawfik@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Arnaud Ebalard 提交于
Now that alarm support for ISL12057 chip is available w/ the specific "isil,irq2-can-wakeup-machine" property, let's use that feature of the driver dedicated to NETGEAR ReadyNAS 102, 104 and 2120 specific routing of RTC Alarm IRQ#2 pin; on those devices, this pin is not connected to the SoC but to a PMIC, which allows the device to be powered up when RTC alarm rings. For that to work, the chip needs to be explicitly marked as a device wakeup source using this "isil,irq2-can-wakeup-machine" boolean property. This makes 'wakealarm' sysfs entry available to configure the alarm. Signed-off-by: NArnaud Ebalard <arno@natisbad.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Peter Huewe <peter.huewe@infineon.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darshana Padmadas <darshanapadmadas@gmail.com> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Grant Likely <grant.likely@linaro.org> Cc: Rob Landley <rob@landley.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Kumar Gala <galak@codeaurora.org> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 09 2月, 2015 2 次提交
-
-
由 Sylwester Nawrocki 提交于
Now when the CDCLK I2S output clock can be handled through the clock API the Odroid X2/U3 can be switched to the simple-audio-card DT binding. Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: NMark Brown <broonie@kernel.org>
-
由 Sylwester Nawrocki 提交于
Clock related properties are added to the Exynos4 I2S device nodes so they can be referred to as clock providers. Missing i2s_opclk1 clock is added to the I2S0 node and clock properties are added to the MAX98090 codec node to allow it to control/read frequency of the MCLK clock directly. Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: NMark Brown <broonie@kernel.org>
-
- 06 2月, 2015 1 次提交
-
-
由 Sylwester Nawrocki 提交于
I2S1, I2S2 on Exynos4 SoC series have limited functionality compared to I2S0, "samsung,s3c6410-i2s" compatible should be used for them. Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: NMark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
-
- 05 2月, 2015 1 次提交
-
-
由 Andy Shevchenko 提交于
Instead of using magic number in the code the patch provides DW_DMA_MAX_NR_MASTERS constant. While here, restrict the reading of data width array by amount of the actual number of AHB masters. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
- 04 2月, 2015 15 次提交
-
-
由 Chanwoo Choi 提交于
This patch add dt node for PPMU_{DMC0|DMC1|LEFTBUS|RIGHTBUS} for exynos4412-trats2 board. Each PPMU dt node includes one event of 'PPMU Count3'. Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com> Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Chanwoo Choi 提交于
This patch adds PPMU dt node for Exynos3250 based Rinato and Monk boards. The PPMU node is used to get the utilization of DMC0/DMC1/ LEFTBUS/RIGHTBUS Block. Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com> Acked-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Chanwoo Choi 提交于
This patch add PPMUs (Platform Performance Monitoring Unit) dt node for Exynos4 (Exynos4210/4212/4412) SoCs. PPMU dt node is used for monitor the utilization of each IP. The Exynos4210/Exynos4212/Exynos4412 SoC includes following PPMUs: - PPMU_DMC0 0x106A_0000 - PPMU_DMC1 0x106B_0000 - PPMU_CPU 0x106C_0000 - PPMU_ACP 0x10AE_0000 - PPMU_RIGHT_BUS 0x112A_0000 - PPMU_LEFT_BUS 0x116A_0000 - PPMU_FSYS 0x1263_0000 - PPMU_LCD0 0x11E4_0000 - PPMU_CAMIF 0x11AC_0000 - PPMU_IMAGE 0x12AA_0000 - PPMU_TV 0x12E4_0000 - PPMU_3D 0x1322_0000 - PPMU_MFC_LEFT 0x1366_0000 - PPMU_MFC_RIGHT 0x1367_0000 Additionally, the Exynos4210 SoC includes following PPMUs: - PPMU_LCD1 0x1224_0000 Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com> Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Chanwoo Choi 提交于
This patch adds PPMU (Platform Performance Monitoring Unit) dt node to estimate the utilization of each IP in Exynos SoC through DEVFREQ Event subsystem. This patch adds following PPMU dt nodes: - PPMU_DMC0 0x106a0000 - PPMU_DMC1 0x106b0000 - PPMU_RIGHTBUS 0x112A0000 - PPMU_LEFTBUS 0x116A0000 - PPMU_CAMIF 0x11AC0000 - PPMU_LCD0 0x11E40000 - PPMU_FSYS 0x12630000 - PPMU_3D 0x13220000 - PPMU_MFC 0x13660000 - PPMU_CPU 0x106c0000 Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com> Acked-by: NKyungmin Park <kyungmin.park@samsung.com> Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 YoungJun Cho 提交于
This patch adds mipi dsi device node to exynos4415.dtsi. Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com> Acked-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 YoungJun Cho 提交于
This patch adds fimd device node to exynos4415.dtsi. Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com> Acked-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Sylwester Nawrocki 提交于
This is required to fix regression after introducing the PMU device nodes required for the PMU driver modified in commit 14fc8b93 ("ARM: EXYNOS: Add platform driver support for Exynos PMU"). This change is needed to make MIPI DSI displays and MIPI CSI-2 camera sensors working again on Exynos4 boards. Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Inha Song 提交于
This patch add WM1811 audio codec, I2S interface and the sound machine nodes to enable audio on exynos4412-trats2 board. Signed-off-by: NInha Song <ideal.song@samsung.com> Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Sylwester Nawrocki 提交于
In order to get exact 24MHz clock frequency value for the camera sensor and avoid rounding errors the parent clock must be CLK_XUSBXTI, not CLK_MOUT_MPLL_USER_T. Currently the sensor's master clock frequency is too high and the sensor doesn't work properly. This fixes commit 0357a443 ("ARM: dts: Specify default clocks for Exynos4 camera devices"). Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Sylwester Nawrocki 提交于
Assign proper FIMC-IS UART gate clock in the device DT node and not use the SRC_MASK gate. This fixes regression introduced in commit a37c82a3 ("clk: samsung: exynos4: Remove SRC_MASK_ISP gates"). Without this change exynos4 fimc-is driver fails to probe with an error log: [ 1.842447] ERROR: could not get clock /camera/fimc-is@12000000:uart(13) [ 1.848529] exynos4-fimc-is 12000000.fimc-is: failed to get clock: uart [ 1.855275] exynos4-fimc-is: probe of 12000000.fimc-is failed with error -2 Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Krzysztof Kozlowski 提交于
Add to Trats2 DTS new node for configuring the max77693 charger driver. Only the maxim,constant-microvolt differs from default value but set all of the optional properties anyway. Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Krzysztof Kozlowski 提交于
Remove fixed regulators (duplicating what max77686 provides) and add GPIO enable control to max77686 regulators. This gives the system full control over those regulators. Previously the state of such regulators was a mixture of what max77686 driver set over I2C and what regulator-fixed set through GPIO. Removal of 'regulator-always-on' from CAM_ISP_CORE_1.2V (buck9) allows disabling it when it is not used. Previously this regulator was always enabled because its enable state is a OR of: - ENB9 GPIO (turned always on by regulator-fixed), - BUCK9EN field in BUCK9CTRL register (off by max77686 through I2C). Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Krzysztof Kozlowski 提交于
Add suspend to RAM configuration for max77686 regulators. Some LDOs and bucks are disabled. This reduces energy consumption during S2R, approximately from 17 mA to 9 mA. Additionally remove old and not supported bindings: - regulator-mem-off - regulator-mem-idle - regulator-mem-on The max77686 driver does not parse them and they are not documented anywere. Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk> Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Krzysztof Kozlowski 提交于
Add node for fuel gauge present in Maxim 77693 PMIC. This allows control over battery charging state on Trats2 board. The fuel gauge is compatible with max17042 battery driver (Maxim 17042/17047/17050). Although datasheet rev 2.2 for MAX77693 describes fuel gauge as Maxim 17042-like, the chip on Trats2 board identifies itself as Maxim 17047-like. Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: NKukjin Kim <kgene@kernel.org>
-
由 Vignesh R 提交于
The charge delay value is by default 0x400. But it can be set to lower values on some boards, as long as false pen-ups are avoided. Lowering the value increases the sampling rate (though current sampling rate is sufficient for TSC operation). In some boards, the value has to be increased to avoid false pen-up events. Hence, charge delay has been made a DT parameter. Signed-off-by: NVignesh R <vigneshr@ti.com> Acked-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
-
- 03 2月, 2015 1 次提交
-
-
由 Tomasz Figa 提交于
This patch adds stdout-path property to chosen nodes of Exynos4 boards to enable use of earlycon feature without the need to hardcode port number in kernel itself. Signed-off-by: NTomasz Figa <t.figa@samsung.com> Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 31 1月, 2015 5 次提交
-
-
由 Tony Lindgren 提交于
Looks like on 3517 davinci_emac MAC address registers have a different layout compared to dm816x and am33xx. Let's add a function to get the 3517 MAC address. Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Roger Quadros 提交于
On this board USB2 is meant to be used as peripheral only. The ID pin for USB2 is hardwired HIGH. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
On this EVM, the USB cable state has to be determined via the ID pin tied to a GPIO line. We use the gpio-usb-extcon driver to read the ID pin and the extcon framework to forward the USB cable state information to the USB driver so the controller can be configured in the right mode (host/peripheral). NOTE: the ports on this board cannot switch roles. They are configured either host or peripheral by hardwiring the respective ID pins. Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
On this EVM, the USB cable state has to be determined via the ID pin tied to a GPIO line. We use the gpio-usb-extcon driver to read the ID pin and the extcon framework to forward the USB cable state information to the USB driver so the controller can be configured in the right mode (host/peripheral). Gets USB peripheral mode to work on this EVM. Signed-off-by: NRoger Quadros <rogerq@ti.com> Reviewed-by: NFelipe Balbi <balbi@ti.com> Acked-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
由 Roger Quadros 提交于
On this EVM, the USB cable state has to be determined via the ID pin tied to a GPIO line. We use the gpio-usb-extcon driver to read the ID pin and the extcon framework to forward the USB cable state information to the USB driver so the controller can be configured in the right mode (host/peripheral). Gets USB peripheral mode to work on this EVM. Signed-off-by: NRoger Quadros <rogerq@ti.com> Reviewed-by: NFelipe Balbi <balbi@ti.com> Acked-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 30 1月, 2015 5 次提交
-
-
由 Peter Griffin 提交于
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161, update the miphy365 phy driver to access sysconfig register offsets via syscfg dt property. This is because the reg property should not be mixing address spaces like it does currently for miphy365. This change then also aligns us to how other platforms such as keystone and bcm7445 pass there syscon offsets via DT. This patch breaks DT compatibility, but this platform is considered WIP, and is only used by a few developers who are upstreaming support for it. This change has been done as a single atomic commit to ensure it is bisectable. Signed-off-by: NPeter Griffin <peter.griffin@linaro.org> Reviewed-by: NArnd Bergmann <arnd@arndb.de> Acked-by: NMaxime Coquelin <maxime.coquelin@st.com> Tested-by: NMaxime Coquelin <maxime.coquelin@st.com>
-
由 Heiko Stuebner 提交于
Currently the hdmi driver is using one of the soc i2c busses for ddc probing and while documentation always specifies i2c5 as hdmi-i2c it could very well be any other bus as well. Therefore this is a property of the board and should be specified there. Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
-
由 Heiko Stuebner 提交于
This enables the recently added display nodes on the firefly and evb, letting the boards output graphic data over the hdmi port. This includes enabling of i2c5 on the evb that is used for ddc probing and setting the lcd-regulators to always on until the hdmi driver learns about using them. Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
-
由 Heiko Stuebner 提交于
Use the same transfer speed on both the rk808 and act8846 variants and remove the status=okay from the rk808 one which is already set in the shared rk3288-evb.dtsi . Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
-
由 Heiko Stuebner 提交于
The evaluation board using the act8846 as main pmic uses two additional regulators to provide the cpu and gpu voltage. Add these and also add the link to cpu supply from vdd_cpu. Signed-off-by: NHeiko Stuebner <heiko@sntech.de> Tested-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
-