Signed-off-by: NEric Bénard <eric@eukrea.com>

this patch really configure the GPIO in GPIO mode.
Signed-off-by: NEric Bénard <eric@eukrea.com>

Tested on i.MX25 and i.MX35 and i.MX51
Signed-off-by: NEric Bénard <eric@eukrea.com>

the attached patch allows SD to work on i.MX51 with Wolfram's drivers
Tested on i.MX51.

Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: NEric Bénard <eric@eukrea.com>

Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: NEric Bénard <eric@eukrea.com>

Signed-off-by: NEric Bénard <eric@eukrea.com>

Signed-off-by: NEric Bénard <eric@eukrea.com>

Signed-off-by: NEric Bénard <eric@eukrea.com>

the PHY is UTMI so don't create an ULPI viewpoint.
Signed-off-by: NEric Bénard <eric@eukrea.com>

Without this exiting WFI can result in cache corruption.
Code taken from Freescale's 2.6.27 BSP and tested on i.MX35
Signed-off-by: NEric Bénard <eric@eukrea.com>

this patch fix the following errors :
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
    error: ‘MX25_SDMA_BASE_ADDR’ undeclared here (not in a function)
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
    error: ‘MX25_INT_SDMA’ undeclared here (not in a function)
Signed-off-by: NEric Bénard <eric@eukrea.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID

* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: NEric Bénard <eric@eukrea.com>

During the reorganisation of the imx-i2c devices
(in 64de5ec1) the 3rd imx-i2c device
for the mx35 got lost. This patch adds the missing device.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.

Applies on 2.6.36-rc7
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: NAmit Kucheria <amit.kucheria@canonical.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Ethernet hangs off OTG
Signed-off-by: NAmit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Get serial port working for now
Signed-off-by: NAmit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The i.MX51 ECSPI has a fifo size of 64 entries instead of 8 entries as
found on the other cspi bus devices.

Cc: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

So the correct clock will be taken for each of the two independent
controllers.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Documentation/gpio.txt specifies that the value argument to
gpio_set_value() should be handled as a boolean (E.G. != 0 is high),
so use the same logic as in _set_direction().
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

i.MX35 CPUs marked with "MCIMX357CJQ5C M99V CTHA0943B" are coming with bogus
L2 cache settings. If these settings are kept unmodified prior enabling the L2
cache the CPU runs amok immediately when its enabled.

This fix should not hurt already working CPUs, as they are using the written
register value already.

Its currently unknown if its possible to detect the production lot from the
software to fix only affected CPUs.

While at it, make sure that mxc_init_l2x0 is only executed on i.MX31/35
Signed-off-by: NJuergen Beisert <jbe@pengutronix.de>
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This fixes

	arch/arm/mach-mx3/mach-cpuimx35.c:143: warning: 'otg_pdata' defined but not used
	arch/arm/mach-mx3/mach-cpuimx35.c:148: warning: 'usbh1_pdata' defined but not used

when USB_ULPI is not selected.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Based on work done earlier by Sascha Hauer
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NEric Bénard <eric@eukrea.com>
[ukl: actually squash the two approaches together]
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Also, remove the deprecated symbols from arch/arm/mach-mx3/cpu.c
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

- remove functions which are no more necessary for tsc2007
- indent platform_data for better readability
Signed-off-by: NEric Bénard <eric@eukrea.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The first argument to I2C_BOARD_INFO is used to assign .type, so it should
not be specified a second time.

For the rtc-pcf8563/pcf8563 entry gcc preferred pcf8563, so did I.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This fixes the following sparse warning:

	arch/arm/mach-imx/pcm970-baseboard.c:224:13: warning: symbol 'pcm970_baseboard_init' was not declared. Should it be static?
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Making the lists signed fixes sparse warnings like:

	arch/arm/mach-imx/mach-mx27_3ds.c:94:31: warning: incorrect type in argument 1 (different signedness)
	arch/arm/mach-imx/mach-mx27_3ds.c:94:31:    expected int const *pin_list
	arch/arm/mach-imx/mach-mx27_3ds.c:94:31:    got unsigned int static [toplevel] *<noident>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This fixes the following sparse warning:

	arch/arm/mach-imx/pcm970-baseboard.c:203:30: warning: symbol 'pcm970_sja1000_platform_data' was not declared. Should it be static?
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This fixes many sparse warnings like:

	arch/arm/mach-imx/clock-imx27.c:597:1: warning: Using plain integer as NULL pointer
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Currently the uarts and timer only work because they are
turned on by reset default. Make them secondary clocks
of their corresponding peripheral clocks to make sure they
are turned on when necessary. Also, register some clocks
to get rid of compiler warnings
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>