Sorry, one of the patches I sent in an earlier series
has some dumb mistakes. One was that I had changed the
parameter for the errata workaround function but forgot
to make that change in the code that called it.

The second mistake was a forgotten return value at the end
of the function in case the workaround was not needed.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TSO packets with one segment or with an MSS less than 224 can
cause errors on some backing devices, so disable GSO in those cases.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some backing devices cannot handle small packets well,
so pad any small packets to avoid that. It was recommended
that the VNIC driver should not send packets smaller than the
minimum MTU value provided by firmware, so pad small packets
to be at least that long.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The extra four bytes of a VLAN packet was throwing off
TX buffer entry values used by the driver. Account for those
bytes when in buffer size and buffer entry calculations
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a VLAN tag is present in the Ethernet header, account
for that when providing the L2 header to firmware.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If port VLAN is enabled, set PFQDE.HIDE_VLAN during VF reset.

Setting only PFQDE.PFQDE during VF reset was clearing PFQDE.HIDE_VLAN.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The new ixgbevf_set_rx_buffer_len() function causes a harmless warnings
in configurations with large page size:

drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c: In function 'ixgbevf_set_rx_buffer_len':
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1758:15: error: unused variable 'max_frame' [-Werror=unused-variable]

This rephrases the code so that the compiler can see the use of that
variable, making it slightly easier to read in the process.

Fixes: f15c5ba5 ("ixgbevf: add support for using order 1 pages to receive large frames")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe enabled rlec counter and the rx_error used it.
We can export the counter directly via ethtool -S ethX.
Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With commit 7f05b467 ("xfrm: check for xdo_dev_state_free")
we no longer need to add an empty callback function
to the driver, so now let's remove the useless code.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix up the Tx trailer length calculation.  We can't believe the
trailer len from the xstate information because it was calculated
before the packet was put together and padding added.  This bit
of code finds the padding value in the trailer, adds it to the
authentication length, and saves it so later we can put it into
the Tx descriptor to tell the device where to stop the checksum
calculation.

Fixes: 59259470 ("ixgbe: process the Tx ipsec offload")
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure the Security Association is using
a 128-bit authentication, since that's the only
size that the hardware offload supports.
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes the following sparse warnings:

drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:371:5: warning:
 symbol 'mlxsw_sp_kvdl_single_occ_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:384:5: warning:
 symbol 'mlxsw_sp_kvdl_chunks_occ_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:397:5: warning:
 symbol 'mlxsw_sp_kvdl_large_chunks_occ_get' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Functions lan743x_csr_read and lan743x_csr_read are local to the source
and do not need to be in global scope, so make them static.

Cleans up sparse warning:
drivers/net/ethernet/microchip/lan743x_main.c:56:5: warning: symbol
lan743x_csr_read' was not declared. Should it be static?
drivers/net/ethernet/microchip/lan743x_main.c:61:6: warning: symbol
'lan743x_csr_write' was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function lan743x_phy_init assigns pointer 'netdev' but this is never read
and hence it can be removed. The return error code handling can also be
cleaned up to remove the variable 'ret'.

Function lan743x_phy_link_status_change assigns pointer 'phy' twice and
this is never read, so it also can be removed.

Finally, function lan743x_tx_napi_poll initializes pointer 'adapter'
and then re-assigns the same value into this pointer a little later on
so this second assignment is redundant and can be also removed.

Cleans up clang warnings:
drivers/net/ethernet/microchip/lan743x_main.c:951:2: warning: Value
stored to 'netdev' is never read
drivers/net/ethernet/microchip/lan743x_main.c:971:3: warning: Value
stored to 'phy' is never read
drivers/net/ethernet/microchip/lan743x_main.c:1583:26: warning: Value
stored to 'adapter' during its initialization is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlxsw_spectrum supports offloading of a tc action mirred egress mirror
to a gretap or an ip6gretap netdevice, which necessitates calls to
functions defined in ip_gre, ip6_gre and ip6_tunnel modules. Previously
this was enabled by introducing a hard dependency of MLXSW_SPECTRUM on
NET_IPGRE and IPV6_GRE. However the rest of mlxsw is careful about
picking which modules are absolutely required, and therefore the better
approach is to make mlxsw_spectrum tolerant of absence of one or both of
the GRE flavors.

Hence rework the NET_IPGRE and IPV6_GRE dependencies to just guard
matching modularity, and hide the corresponding code in spectrum_span.c
in an #if IS_ENABLED. Mark mlxsw_sp_span_entry_tunnel_parms_common as
maybe unused, to muffle warnings if neither GRE flavor is selected,
which seems cleaner than introducing a composite #if.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the function next to the rest of gretap4 functions. Thus the
generic functions shared between gretap4 and gretap6 are in one block at
the beginning, followed by a gretap4 block, followed by a gretap6 block.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to abstract away access to the
ipv6.sysctl.multipath_hash_policy variable, which is not available on
systems compiled without IPv6 support, introduce a wrapper function
ip6_multipath_hash_policy() that falls back to 0 on non-IPv6 systems.

Use this wrapper from mlxsw/spectrum_router instead of a direct
reference.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

check firmware capabilities before setting ethtool
link mode mask, also add few missing speeds.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

50Gbps is a supported speed, Stop reporting it as
unsupported speed.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a scenario where the command queued to firmware get dropped or times
out, MTU change from host will not propagate to firmware. So, it is
required for host driver to wait for response from firmware or timeout
and then return correct status to caller of ndo_change_mtu.

Also moved the common code for MTU change from PF and VF driver files to
common file lio_core.c
Signed-off-by: NVeerasenareddy Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF changes unicast mac address by sending mailbox msg to PF, then PF
completes the mac address modification. It may fail when the target
uc mac address is already in the mac_vlan table. VF should be aware
of it by reading the message result.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's not allowed to add two same unicast mac address entries to the
mac_vlan table. When modify the uc mac address of a VF device to the
same value with the PF device's, the PF device will lose its entry of
the mac_vlan table.

Lookup the mac address in the mac_vlan table, and add it if the entry
is inexistent.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Error code -EIO was used to indicate mutilple errors in function
hclge_get_mac_vlan_cmd_status().This patch fixes it by using
error code depending on the error type.

For no space error, return -ENOSPC.
For entry not found, return -ENOENT.
For command send fail, return -EIO.
For invalid op code, return -EINVAL.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An enum type variable was used to store an "int" type return value.
This patch fixes it.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the buffer overflow warning by refactoring
hclgevf_bind_ring_to_vector and hclge_get_ring_chain_from_mbx.

Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: dde1a86e ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vlan ctag filter is enabled, the loopback selftest fails because
loopback selftest does not support vlan.

This patch fixes it by disabling the vlan ctag filter when runnig
loopback selftest.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add support for querying pfc puase packets statistic
in hclge_ieee_getpfc, which is used to tell user how many pfc
puase packets have been sent and received by this mac port.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Original skb->truesize reports the received packet size,
not the actual buffer size NIC driver allocated(1 Page).
The linux net protocol will misjudge the true size of rx queue.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the firmware cmd to setup mac pause params is the same as the
firmware cmd to pfc pause params, this patch unifies the pause params
setup function.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function of dev_close and dev_open is just likes ifconfig <netif> down
and ifconfig <netif> up. The ipv6 address will be lost after dev_close and
dev_open are called. This patch uses hns3_nic_net_stop to replace dev_close
and uses hns3_nic_net_open to replace dev_open.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.

This patch fixes it by updating the link state in ae_stop function.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When driver is in initial state, the mac_vlan table table is empty.
So the delete operation for mac address must fail. Existence check
is needed here. Otherwise, the error message will make user confused.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T6 cards can support up to 100 G speeds. So, increase
max programmable tx rate limit to 100 Gbps.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the coalesce configuation lost problem when
setting the channel number by restoring all vectors's coalesce
configuation to vector 0's, because all vectors belonging to
the same netdev have the same coalesce configuation for now.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refoctors the coalesce related struct by introducing
the hns3_enet_coalesce struct, in order to fix the coalesce
configuation lost problem when changing the channel number.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Coalesce configuration will be set to default value by
hns3_nic_init_vector_data during reset, which causes the
coalesce configuration loss problem.

This patch fixes it by setting the default value in
hns3_nic_alloc_vector_data, which will not be called in the
reset process.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a get_vector function, which allocate the vectors
for a client, but there is not a put_vector to free the
vector.

This patch introduces the put_vector function in order to
fix the coalesce configuration lost problem during reset
process.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In hns3_set_ringparam, hns3_uninit_all_ring frees the
memory pointed by priv->ring_data[i].ring, and
hns3_change_all_ring_bd_num use that pointer without mallocing,
which will cause a use-after-free problem.

The patch fixes it by not freeing the memory in
hns3_uninit_all_ring, and uses hns3_put_ring_config to free it
when necessary.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pause configuration will be set to default value by hclge_tm_schd_init
during reset, which causes the RSS configuration loss problem.

This patch fixes it by calling hclge_tm_init_hw during reset process
, which will set the pause configuration to default value.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RSS configuration will be set to default value by hclge_rss_init_hw
during reset, which causes the RSS configuration loss problem.

This patch fixes it by setting the default value in
hclge_rss_init_cfg function, which will not be called in the reset
process.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>