'struct timeval' uses a 32-bit seconds field which will overflow in
year 2038 and beyond. This patch is part of a larger effort to remove
all instances of 'struct timeval' from the kernel and replace them
with 64-bit timekeeping variables.
The patch also fixes the debug printf specifier to avoid the
seconds value being truncated.
The patch was build-tested / debugged by removing the
"if VERBOSE > SHOW_ERROR_MESSAGES" guards.
Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When dev_alloc_skb or pci_dma_mapping_error in rtl8180_init_rx_ring fails,
the memory allocated by pci_zalloc_consistent is not freed.

This patch fixes the bug by adding pci_free_consistent
in error handling code.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The references to some arrays in the rtl8xxxu driver were moved inside
of an #ifdef, but the symbols remain outside, resulting in build warnings:

rtl8xxxu/rtl8xxxu.c:1506:33: error: 'rtl8188ru_radioa_1t_highpa_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1431:33: error: 'rtl8192cu_radioa_1t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1407:33: error: 'rtl8192cu_radiob_2t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1332:33: error: 'rtl8192cu_radioa_2t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:239:35: error: 'rtl8192c_power_base' defined but not used
rtl8xxxu/rtl8xxxu.c:217:35: error: 'rtl8188r_power_base' defined but not used

This adds an extra #ifdef around them to shut up the warnings.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 2fc0b8e5 ("rtl8xxxu: Add TX power base values for gen1 parts")
Fixes: 4062b8ff ("rtl8xxxu: Move PHY RF init into device specific functions")
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Update the MAINTAINERS info to reflect active development of the
rtl8xxxu driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

All the disable_rf() functions were setting REG_TXPAUSE to 0xff to
stop transmission. Do it centrally before calling disable_rf()
instead.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This implements an 8192eu specific enable_rf() function. The 8192eu is
not a combo device, so no need for doing the BT specific bits needed
by the 8723bu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This driver relies on driver_info in struct usb_device_id, so allowing
adding a device via /sys/bus/usb/drivers/rtl8xxxu/new_id will cause a
NULL pointer dereference.

Set .no_dynamic_id = 1 to disable hot add of USB IDs.
Reported-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8188RU does not like PAPE to be enabled, while all the other gen1
parts seem to require it.

This makes the RTL8188RU able to associate for me.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This register is undocumented in the vendor code, but it is set
unconditionally for all 8192cu/8188cu/8188ru parts.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This fixes a long standing bug where mac80211 would send disconnect
packets to the device, after we had shut down the device.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In particular set APS_FSMCO_WLON_RESET in the right register, and do
not overwrite too much of REG_CR.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is simpler than checking for RTL8188C && hi_pa.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch was being missed since rtl_chip will never match RTL8188C
if hi_pa is true.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Per the vendor driver, devices with an external PA needs limiting it's
TX power to 0x20.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Load the RF table in init_phy_rf(), which allows for applying device
specific RF hacks in the same place. Getting rid of more ugly if ()
clutter.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

several functions are not initializing a return status in ret
resulting in garbage to be returned instead of 0 for success.
Currently, the calls to these functions are not checking the
return, however, it seems prudent to return the correct status
in case they are to be checked at a later date.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This dongle was tested successfully by Andrea Merello
Reported-by: NAndrea Merello <andrea.merello@gmail.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Revert "rtl8xxxu: Temporarily disable 8192eu device init"

This reverts commit ccfe1e85.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Write the adjusted value back to the correct register
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This removes an unneeded hack for 8192eu, and allows for initializing
REG_FPGA0_XAB_RF_SW_CTRL at the same point as it is done for all other
parts.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This removes a bunch of if () spaghetti and re-applies the USB bus
quirks for 8188/8192 that had gotten lost.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Rather than scattering the code with #ifdefs, use the fileops
structure to hold device specific PBP values.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This was expired by the vendor driver, but we never ended up using the
backed up value.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This removes another case of ugly if () clutter
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Move setting it to rtl8723au_init_phy_bb()
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This moves the loading of the AGC table into init_phy_bb() and reduces
the if() clutter.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This should get the order right and avoid patching something that is
later overwritten.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This reduces the if () clutter. Longer term it probably makes sense to
split this between gen1 (8723au/8188cu/8192cu) and gen2
(8192eu/8723bu) devices.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This reduce the use of magic values a little.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The old code incorrectly wiped out bits 0-23 by mistake when setting
the RX path for 1T parts.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8723bu is a combo WiFi/BT dongle, and path B is not used for WiFi,
so no point in calibrating it.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

No actual code flow change, but no need to warn about something that
isn't a prioblem.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This caught a bug where too little memory was allocated for RX urbs
for parts using 24 byte RX descriptors
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This shouldn't affect little endian system, but may have prevented the
driver working on big endian systems for devices with the larger 24
byte RX descriptors.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Instead use tx_desc_size() to distinguish between gen1
(8723a/8192c/8188c) and gen2 (8723b/8192e) parts.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8192eu is a 2T part, so setting TX power for path A only, as done by
rtl8723bu_set_tx_power() is not sufficient.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Presumably 8192eu devices do not have leds, so do not enable them.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Like the 8723bu, the vendor driver does not set FPGA0_TX_INFO for
8192eu in the init sequence.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>