all architectures converted
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Support is hooked up via a cpu start method specified in the device
tree, and also depends on DT nodes that describe the interfaces for
performing IPI and identifying which cpu execution is taking place on.
The currently used method is a form of spin table, where secondary
cpus are unblocked by writing to a special address.
Signed-off-by: NRich Felker <dalias@libc.org>

At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.

Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.

No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.
Signed-off-by: NRich Felker <dalias@libc.org>

There is no arch-specific sched_clock implementation for sh, resulting
in use of the old default jiffies-based implementation. Instead, use
the modern generic sched_clock framework so that drivers can register
better backends.
Signed-off-by: NRich Felker <dalias@libc.org>

The futex cmpxchg runtime testing in kernel/futex.c depends on
accesses to address 0 producing EFAULT, which obviously does not work
on nommu. Since SH always has cmpxchg, disable the broken runtime
detection.

At some point this should be fixed at the kernel/futex.c level. UP
machines can always provide a working cmpxchg with interrupt masking,
and SMP cannot function without a working cmpxchg anyway.
Signed-off-by: NRich Felker <dalias@libc.org>

Signed-off-by: NRich Felker <dalias@libc.org>

This replaces:

- "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB" as this can
  now be selected directly.

- "select ARCH_WANT_OPTIONAL_GPIOLIB" with no dependency: GPIOLIB
  is now selectable by everyone, so we need not declare our
  intent to select it.

When ordering the symbols the following rationale was used:
if the selects were in alphabetical order, I moved select GPIOLIB
to be in alphabetical order, but if the selects were not
maintained in alphabetical order, I just replaced
"select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB".

Cc: Michael Büsch <m@bues.ch>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The binary GCD algorithm is based on the following facts:
	1. If a and b are all evens, then gcd(a,b) = 2 * gcd(a/2, b/2)
	2. If a is even and b is odd, then gcd(a,b) = gcd(a/2, b)
	3. If a and b are all odds, then gcd(a,b) = gcd((a-b)/2, b) = gcd((a+b)/2, b)

Even on x86 machines with reasonable division hardware, the binary
algorithm runs about 25% faster (80% the execution time) than the
division-based Euclidian algorithm.

On platforms like Alpha and ARMv6 where division is a function call to
emulation code, it's even more significant.

There are two variants of the code here, depending on whether a fast
__ffs (find least significant set bit) instruction is available.  This
allows the unpredictable branches in the bit-at-a-time shifting loop to
be eliminated.

If fast __ffs is not available, the "even/odd" GCD variant is used.

I use the following code to benchmark:

	#include <stdio.h>
	#include <stdlib.h>
	#include <stdint.h>
	#include <string.h>
	#include <time.h>
	#include <unistd.h>

	#define swap(a, b) \
		do { \
			a ^= b; \
			b ^= a; \
			a ^= b; \
		} while (0)

	unsigned long gcd0(unsigned long a, unsigned long b)
	{
		unsigned long r;

		if (a < b) {
			swap(a, b);
		}

		if (b == 0)
			return a;

		while ((r = a % b) != 0) {
			a = b;
			b = r;
		}

		return b;
	}

	unsigned long gcd1(unsigned long a, unsigned long b)
	{
		unsigned long r = a | b;

		if (!a || !b)
			return r;

		b >>= __builtin_ctzl(b);

		for (;;) {
			a >>= __builtin_ctzl(a);
			if (a == b)
				return a << __builtin_ctzl(r);

			if (a < b)
				swap(a, b);
			a -= b;
		}
	}

	unsigned long gcd2(unsigned long a, unsigned long b)
	{
		unsigned long r = a | b;

		if (!a || !b)
			return r;

		r &= -r;

		while (!(b & r))
			b >>= 1;

		for (;;) {
			while (!(a & r))
				a >>= 1;
			if (a == b)
				return a;

			if (a < b)
				swap(a, b);
			a -= b;
			a >>= 1;
			if (a & r)
				a += b;
			a >>= 1;
		}
	}

	unsigned long gcd3(unsigned long a, unsigned long b)
	{
		unsigned long r = a | b;

		if (!a || !b)
			return r;

		b >>= __builtin_ctzl(b);
		if (b == 1)
			return r & -r;

		for (;;) {
			a >>= __builtin_ctzl(a);
			if (a == 1)
				return r & -r;
			if (a == b)
				return a << __builtin_ctzl(r);

			if (a < b)
				swap(a, b);
			a -= b;
		}
	}

	unsigned long gcd4(unsigned long a, unsigned long b)
	{
		unsigned long r = a | b;

		if (!a || !b)
			return r;

		r &= -r;

		while (!(b & r))
			b >>= 1;
		if (b == r)
			return r;

		for (;;) {
			while (!(a & r))
				a >>= 1;
			if (a == r)
				return r;
			if (a == b)
				return a;

			if (a < b)
				swap(a, b);
			a -= b;
			a >>= 1;
			if (a & r)
				a += b;
			a >>= 1;
		}
	}

	static unsigned long (*gcd_func[])(unsigned long a, unsigned long b) = {
		gcd0, gcd1, gcd2, gcd3, gcd4,
	};

	#define TEST_ENTRIES (sizeof(gcd_func) / sizeof(gcd_func[0]))

	#if defined(__x86_64__)

	#define rdtscll(val) do { \
		unsigned long __a,__d; \
		__asm__ __volatile__("rdtsc" : "=a" (__a), "=d" (__d)); \
		(val) = ((unsigned long long)__a) | (((unsigned long long)__d)<<32); \
	} while(0)

	static unsigned long long benchmark_gcd_func(unsigned long (*gcd)(unsigned long, unsigned long),
								unsigned long a, unsigned long b, unsigned long *res)
	{
		unsigned long long start, end;
		unsigned long long ret;
		unsigned long gcd_res;

		rdtscll(start);
		gcd_res = gcd(a, b);
		rdtscll(end);

		if (end >= start)
			ret = end - start;
		else
			ret = ~0ULL - start + 1 + end;

		*res = gcd_res;
		return ret;
	}

	#else

	static inline struct timespec read_time(void)
	{
		struct timespec time;
		clock_gettime(CLOCK_PROCESS_CPUTIME_ID, &time);
		return time;
	}

	static inline unsigned long long diff_time(struct timespec start, struct timespec end)
	{
		struct timespec temp;

		if ((end.tv_nsec - start.tv_nsec) < 0) {
			temp.tv_sec = end.tv_sec - start.tv_sec - 1;
			temp.tv_nsec = 1000000000ULL + end.tv_nsec - start.tv_nsec;
		} else {
			temp.tv_sec = end.tv_sec - start.tv_sec;
			temp.tv_nsec = end.tv_nsec - start.tv_nsec;
		}

		return temp.tv_sec * 1000000000ULL + temp.tv_nsec;
	}

	static unsigned long long benchmark_gcd_func(unsigned long (*gcd)(unsigned long, unsigned long),
								unsigned long a, unsigned long b, unsigned long *res)
	{
		struct timespec start, end;
		unsigned long gcd_res;

		start = read_time();
		gcd_res = gcd(a, b);
		end = read_time();

		*res = gcd_res;
		return diff_time(start, end);
	}

	#endif

	static inline unsigned long get_rand()
	{
		if (sizeof(long) == 8)
			return (unsigned long)rand() << 32 | rand();
		else
			return rand();
	}

	int main(int argc, char **argv)
	{
		unsigned int seed = time(0);
		int loops = 100;
		int repeats = 1000;
		unsigned long (*res)[TEST_ENTRIES];
		unsigned long long elapsed[TEST_ENTRIES];
		int i, j, k;

		for (;;) {
			int opt = getopt(argc, argv, "n:r:s:");
			/* End condition always first */
			if (opt == -1)
				break;

			switch (opt) {
			case 'n':
				loops = atoi(optarg);
				break;
			case 'r':
				repeats = atoi(optarg);
				break;
			case 's':
				seed = strtoul(optarg, NULL, 10);
				break;
			default:
				/* You won't actually get here. */
				break;
			}
		}

		res = malloc(sizeof(unsigned long) * TEST_ENTRIES * loops);
		memset(elapsed, 0, sizeof(elapsed));

		srand(seed);
		for (j = 0; j < loops; j++) {
			unsigned long a = get_rand();
			/* Do we have args? */
			unsigned long b = argc > optind ? strtoul(argv[optind], NULL, 10) : get_rand();
			unsigned long long min_elapsed[TEST_ENTRIES];
			for (k = 0; k < repeats; k++) {
				for (i = 0; i < TEST_ENTRIES; i++) {
					unsigned long long tmp = benchmark_gcd_func(gcd_func[i], a, b, &res[j][i]);
					if (k == 0 || min_elapsed[i] > tmp)
						min_elapsed[i] = tmp;
				}
			}
			for (i = 0; i < TEST_ENTRIES; i++)
				elapsed[i] += min_elapsed[i];
		}

		for (i = 0; i < TEST_ENTRIES; i++)
			printf("gcd%d: elapsed %llu\n", i, elapsed[i]);

		k = 0;
		srand(seed);
		for (j = 0; j < loops; j++) {
			unsigned long a = get_rand();
			unsigned long b = argc > optind ? strtoul(argv[optind], NULL, 10) : get_rand();
			for (i = 1; i < TEST_ENTRIES; i++) {
				if (res[j][i] != res[j][0])
					break;
			}
			if (i < TEST_ENTRIES) {
				if (k == 0) {
					k = 1;
					fprintf(stderr, "Error:\n");
				}
				fprintf(stderr, "gcd(%lu, %lu): ", a, b);
				for (i = 0; i < TEST_ENTRIES; i++)
					fprintf(stderr, "%ld%s", res[j][i], i < TEST_ENTRIES - 1 ? ", " : "\n");
			}
		}

		if (k == 0)
			fprintf(stderr, "PASS\n");

		free(res);

		return 0;
	}

Compiled with "-O2", on "VirtualBox 4.4.0-22-generic #38-Ubuntu x86_64" got:

  zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
  gcd0: elapsed 10174
  gcd1: elapsed 2120
  gcd2: elapsed 2902
  gcd3: elapsed 2039
  gcd4: elapsed 2812
  PASS
  zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
  gcd0: elapsed 9309
  gcd1: elapsed 2280
  gcd2: elapsed 2822
  gcd3: elapsed 2217
  gcd4: elapsed 2710
  PASS
  zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
  gcd0: elapsed 9589
  gcd1: elapsed 2098
  gcd2: elapsed 2815
  gcd3: elapsed 2030
  gcd4: elapsed 2718
  PASS
  zhaoxiuzeng@zhaoxiuzeng-VirtualBox:~/develop$ ./gcd -r 500000 -n 10
  gcd0: elapsed 9914
  gcd1: elapsed 2309
  gcd2: elapsed 2779
  gcd3: elapsed 2228
  gcd4: elapsed 2709
  PASS

[akpm@linux-foundation.org: avoid #defining a CONFIG_ variable]
Signed-off-by: NZhaoxiu Zeng <zhaoxiu.zeng@gmail.com>
Signed-off-by: NGeorge Spelvin <linux@horizon.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

printk() takes some locks and could not be used a safe way in NMI
context.

The chance of a deadlock is real especially when printing stacks from
all CPUs.  This particular problem has been addressed on x86 by the
commit a9edc880 ("x86/nmi: Perform a safe NMI stack trace on all
CPUs").

The patchset brings two big advantages.  First, it makes the NMI
backtraces safe on all architectures for free.  Second, it makes all NMI
messages almost safe on all architectures (the temporary buffer is
limited.  We still should keep the number of messages in NMI context at
minimum).

Note that there already are several messages printed in NMI context:
WARN_ON(in_nmi()), BUG_ON(in_nmi()), anything being printed out from MCE
handlers.  These are not easy to avoid.

This patch reuses most of the code and makes it generic.  It is useful
for all messages and architectures that support NMI.

The alternative printk_func is set when entering and is reseted when
leaving NMI context.  It queues IRQ work to copy the messages into the
main ring buffer in a safe context.

__printk_nmi_flush() copies all available messages and reset the buffer.
Then we could use a simple cmpxchg operations to get synchronized with
writers.  There is also used a spinlock to get synchronized with other
flushers.

We do not longer use seq_buf because it depends on external lock.  It
would be hard to make all supported operations safe for a lockless use.
It would be confusing and error prone to make only some operations safe.

The code is put into separate printk/nmi.c as suggested by Steven
Rostedt.  It needs a per-CPU buffer and is compiled only on
architectures that call nmi_enter().  This is achieved by the new
HAVE_NMI Kconfig flag.

The are MN10300 and Xtensa architectures.  We need to clean up NMI
handling there first.  Let's do it separately.

The patch is heavily based on the draft from Peter Zijlstra, see

  https://lkml.org/lkml/2015/6/10/327

[arnd@arndb.de: printk-nmi: use %zu format string for size_t]
[akpm@linux-foundation.org: min_t->min - all types are size_t here]
Signed-off-by: NPetr Mladek <pmladek@suse.com>
Suggested-by: NPeter Zijlstra <peterz@infradead.org>
Suggested-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: Jan Kara <jack@suse.cz>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>	[arm part]
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jiri Kosina <jkosina@suse.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: David Miller <davem@davemloft.net>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Define HAVE_EXIT_THREAD for archs which want to do something in
exit_thread. For others, let's define exit_thread as an empty inline.

This is a cleanup before we change the prototype of exit_thread to
accept a task parameter.

[akpm@linux-foundation.org: fix mips]
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The code being removed was copied from arm, where the corresponding
code was removed in 2013. The only functional change should be that
the rating of the dummy local timer changes from 400 to 100.
Signed-off-by: NRich Felker <dalias@libc.org>

Include pci/hotplug/Kconfig directly from pci/Kconfig, so arches don't
have to source both pci/Kconfig and pci/hotplug/Kconfig.

Note that this effectively adds pci/hotplug/Kconfig to the following
arches, because they already sourced drivers/pci/Kconfig but they
previously did not source drivers/pci/hotplug/Kconfig:

  alpha
  arm
  avr32
  frv
  m68k
  microblaze
  mn10300
  sparc
  unicore32

Inspired-by-patch-from: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Include pci/pcie/Kconfig directly from pci/Kconfig, so arches don't
have to source both pci/Kconfig and pci/pcie/Kconfig.

Note that this effectively adds pci/pcie/Kconfig to the following
arches, because they already sourced drivers/pci/Kconfig but they
previously did not source drivers/pci/pcie/Kconfig:

  alpha
  avr32
  blackfin
  frv
  m32r
  m68k
  microblaze
  mn10300
  parisc
  sparc
  unicore32
  xtensa

[bhelgaas: changelog, source pci/pcie/Kconfig at top of pci/Kconfig, whitespace]
Signed-off-by: NSasa Bogicevic <brutallesale@gmail.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.

[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NValentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As illustrated by commit a3afe70b ("[S390] latencytop s390
support."), HAVE_LATENCYTOP_SUPPORT is defined by an architecture to
advertise an implementation of save_stack_trace_tsk.

However, as of 9212ddb5 ("stacktrace: provide save_stack_trace_tsk()
weak alias") a dummy implementation is provided if STACKTRACE=y.  Given
that LATENCYTOP already depends on STACKTRACE_SUPPORT and selects
STACKTRACE, we can remove HAVE_LATENCYTOP_SUPPORT altogether.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Helge Deller <deller@gmx.de>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are two kexec load syscalls, kexec_load another and kexec_file_load.
 kexec_file_load has been splited as kernel/kexec_file.c.  In this patch I
split kexec_load syscall code to kernel/kexec.c.

And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.

The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled.  But kexec-tools use
kexec_load syscall can bypass the checking.

Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel.  KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.

Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig.  Also updated general kernel code with to
kexec_load syscall.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NDave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We would want to use number of page table level to define mm_struct.
Let's expose it as CONFIG_PGTABLE_LEVELS.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-sh@vger.kernel.org
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

What sh4 actually wants is HAVE_PATA_PLATFORM, so select that instead.
Signed-off-by: NRob Landley <rob@landley.net>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NKevin Hilman <khilman@linaro.org>

Following the suggestions from Andrew Morton and Stephen Rothwell,
Dont expand the ARCH list in kernel/gcov/Kconfig. Instead,
define a ARCH_HAS_GCOV_PROFILE_ALL bool which architectures
can enable.

set ARCH_HAS_GCOV_PROFILE_ALL on Architectures where it was
previously allowed + ARM64 which I tested.
Signed-off-by: NRiku Voipio <riku.voipio@linaro.org>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It is not valid to select CONFIG_PM directly without selecting
CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME too, because that breaks
dependencies (ia64 does that) and it is not necessary to select
CONFIG_PM directly if CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is
selected, because CONFIG_PM will be set automatically in that
case (sh does that).

Fix those mistakes.
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

New system call depends on crypto.  As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.

But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto.  Remove that dependency.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently the sh-intc driver is compiled on all SuperH and
non-multiplatform SH-Mobile platforms, while it's only used on a limited
number of platforms:
  - SuperH: SH2(A), SH3(A), SH4(A)(L) (all but SH5)
  - ARM: sh7372, sh73a0

Drop the "default y" on SH_INTC, make all CPU platforms that use it
select it, and protect all sub-options by "if SH_INTC" to fix this.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Load purgatory code in RAM and relocate it based on the location.
Relocation code has been inspired by module relocation code and purgatory
relocation code in kexec-tools.

Also compute the checksums of loaded kexec segments and store them in
purgatory.

Arch independent code provides this functionality so that arch dependent
bootloaders can make use of it.

Helper functions are provided to get/set symbol values in purgatory which
are used by bootloaders later to set things like stack and entry point of
second kernel etc.
Signed-off-by: NVivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Nothing sets function_trace_stop to disable function tracing anymore.
Remove the check for it in the arch code.

[ Please test this on your arch ]

Cc: Matt Fleming <matt@console-pimps.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally.  So
HAS_IOPORT_MAP is the better name for this.

Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.

The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available.  I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.

The changes in this commit were done using:

	$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently AUDITSYSCALL has a long list of architecture depencency:
       depends on AUDIT && (X86 || PARISC || PPC || S390 || IA64 || UML ||
		SPARC64 || SUPERH || (ARM && AEABI && !OABI_COMPAT) || ALPHA)
The purpose of this patch is to replace it with HAVE_ARCH_AUDITSYSCALL
for simplicity.
Signed-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com> (arm)
Acked-by: Richard Guy Briggs <rgb@redhat.com> (audit)
Acked-by: Matt Turner <mattst88@gmail.com> (alpha)
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: NEric Paris <eparis@redhat.com>

Now when drivers/clocksource/Kconfig has been
updated with entires for CMT, TMU and MTU2
it is safe to remove these from SH.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Acked-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

USB_ARCH_HAS_EHCI, USB_ARCH_HAS_OHCI, and USB_ARCH_HAS_XHCI were just
removed. Selecting them is a nop. The select statements for these
symbols can be removed too.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove an outdated reference to "most personal computers" having only one
CPU, and change the use of "singleprocessor" and "single processor" in
CONFIG_SMP's documentation to "uniprocessor" across all arches where that
documentation is present.
Signed-off-by: NRobert Graffham <psquid@psquid.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of duplicating the CC_STACKPROTECTOR Kconfig and
Makefile logic in each architecture, switch to using
HAVE_CC_STACKPROTECTOR and keep everything in one place. This
retains the x86-specific bug verification scripts.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/1387481759-14535-2-git-send-email-keescook@chromium.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

We've switched over every architecture that supports SMP to it, so
remove the new useless config variable.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Architectures which support CONFIG_PARPORT_PC should select
ARCH_MIGHT_HAVE_PC_PARPORT.
Signed-off-by: NMark Salter <msalter@redhat.com>
CC: Paul Mundt <lethal@linux-sh.org>
CC: linux-sh@vger.kernel.org

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

commit 40b31360 ("Finally eradicate
CONFIG_HOTPLUG") removed remaining references to CONFIG_HOTPLUG, but missed
a few plain English references in the CONFIG_KEXEC help texts.

Remove them, too.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ever since commit 45f035ab ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off.  Remove all the remaining references to it.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All archs are converted over. Remove the config switch and the
fallback code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

GENERIC_GPIO has been made equivalent to GPIOLIB in architecture code
and all driver code has been switch to depend on GPIOLIB. It is thus
safe to have GENERIC_GPIO removed.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

The Kconfig symbol ARCH_HAS_DEFAULT_IDLE is unused. Commit
a0bfa137 ("cpuidle: stop
depending on pm_idle") removed the only place were it was
actually used. But it did not remove its Kconfig entries (for sh
and x86). Remove those two entries now.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Cc: Len Brown <len.brown@intel.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/1363869683.1390.134.camel@x61.thuisdomeinSigned-off-by: NIngo Molnar <mingo@kernel.org>