Which makes sure that the MTU respects the minimum value of
SCTP_DEFAULT_MINSEGMENT and that it is correctly aligned.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need for this helper.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

and avoid the open-coded versions of it.

Now sctp_datamsg_from_user can just re-use asoc->frag_point as it will
always be updated.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When given a MTU, this function calculates how much payload we can carry
on it. Without a MTU, it calculates the amount of header overhead we
have.

So that when we have extra overhead, like the one added for IP options
on SELinux patches, it is easier to handle it.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All changes to asoc PMTU should now go through this wrapper, making it
easier to track them and to do other actions upon it.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Xin Long, the if() here is always true as PMTU can never
be 0.
Reported-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was only one case that sctp_assoc_add_peer couldn't handle, which
is when SPP_PMTUD_DISABLE is set and pathmtu not initialized.
So add this situation to sctp_transport_route and reuse what was
already in there.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This value is not used anywhere in the code. In essence it is a
duplicate of SCTP_DEFAULT_MINSEGMENT, which is used by the stack.

SCTP_MIN_PMTU value makes more sense, but we should not change to it now
as it would risk breaking applications.

So this patch removes SCTP_MIN_PMTU and adjust the comment above it.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A vti6 interface can carry IPv4 packets too.
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tcp_select_initial_window(), we only set rcv_wnd to
tcp_default_init_rwnd() if current mss > (1 << wscale). Otherwise,
rcv_wnd is kept at the full receive space of the socket which is a
value way larger than tcp_default_init_rwnd().
With larger initial rcv_wnd value, receive buffer autotuning logic
takes longer to kick in and increase the receive buffer.

In a TCP throughput test where receiver has rmem[2] set to 125MB
(wscale is 11), we see the connection gets recvbuf limited at the
beginning of the connection and gets less throughput overall.
Signed-off-by: NWei Wang <weiwan@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
smc fixes from 2018-04-17 - v3

in the mean time we challenged the benefit of these CLC handshake
optimizations for the sockopts TCP_NODELAY and TCP_CORK.
We decided to give up on them for now, since SMC still works
properly without.
There is now version 3 of the patch series with patches 2-4 implementing
sockopts that require special handling in SMC.

Version 3 changes
   * no deferring of setsockopts TCP_NODELAY and TCP_CORK anymore
   * allow fallback for some sockopts eliminating SMC usage
   * when setting TCP_NODELAY always enforce data transmission
     (not only together with corked data)

Version 2 changes of Patch 2/4 (and 3/4):
   * return error -EOPNOTSUPP for TCP_FASTOPEN sockopts
   * fix a kernel_setsockopt() usage bug by switching parameter
     variable from type "u8" to "int"
   * add return code validation when calling kernel_setsockopt()
   * propagate a setsockopt error on the internal CLC socket
     to the SMC socket.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If sockopt TCP_DEFER_ACCEPT is set, the accept is delayed till
data is available.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting sockopt TCP_NODELAY or resetting sockopt TCP_CORK
triggers data transfer.

For a corked SMC socket RDMA writes are deferred, if there is
still sufficient send buffer space available.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several TCP sockopts do not work for SMC. One example are the
TCP_FASTOPEN sockopts, since SMC-connection setup is based on the TCP
three-way-handshake.
If the SMC socket is still in state SMC_INIT, such sockopts trigger
fallback to TCP. Otherwise an error is returned.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The struct smc_cdc_msg must be defined as packed so the
size is 44 bytes.
And change the structure size check so sizeof is checked.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kbuild test robot says:

  >coccinelle warnings: (new ones prefixed by >>)
  >>> net/core/dev.c:1588:2-3: Unneeded semicolon

So, let's remove it.
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c40e89fd ("geneve: configure MTU based on a lower device") added
an IS_ENABLED(CONFIG_IPV6) to geneve, leading to the following link error
with CONFIG_GENEVE=y and CONFIG_IPV6=m:

drivers/net/geneve.o: In function `geneve_link_config':
geneve.c:(.text+0x14c): undefined reference to `rt6_lookup'

Fix this by adding a Kconfig dependency and forcing GENEVE to be a module
when IPV6 is a module.

Fixes: c40e89fd ("geneve: configure MTU based on a lower device")
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/net: updates 2018-04-26

please apply the following patches to net-next. There's the usual
cleanups & small improvements, and Kittipon adds HW offload support
for IPv6 checksumming.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If READ MAC fails to fetch a valid MAC address, allow some more device
types (IQD and z/VM OSD) to fall back to a random address.
Also use eth_hw_addr_random(), for indicating to userspace that the
address type is NET_ADDR_RANDOM.

Note that while z/VM has various protection schemes to prohibit
custom addresses on its NICs, they are all optional. So we should at
least give it a try.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check if a qeth device supports IPv6 RX checksum offload, and hook it up
into the existing NETIF_F_RXCSUM support.
As NETIF_F_RXCSUM is now backed by a combination of HW Assists, we need
to be a little smarter when dealing with errors during a configuration
change:
- switching on NETIF_F_RXCSUM only makes sense if at least one HW Assist
  was enabled successfully.
- for switching off NETIF_F_RXCSUM, all available HW Assists need to be
  deactivated.
Signed-off-by: NKittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check if a qeth device supports IPv6 TX checksum offload, and advertise
NETIF_F_IPV6_CSUM accordingly. Add support for setting the relevant bits
in IPv6 packet descriptors.

Currently this has only limited use (ie. UDP, or Jumbo Frames). For any
TCP traffic with a standard MSS, the TCP checksum gets calculated
as part of the linear GSO segmentation.
Signed-off-by: NKittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some wrappers to make the protocol-specific Assist code a little
more generic, and use them for sending protocol-agnostic commands in
the Checksum Offload Assist code.
Signed-off-by: NKittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For new functionality, the L2 subdriver will start using IPv6 assists.
So move the query from the L3 subdriver into the common setup path.
Signed-off-by: NKittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This matches the statistics we gather for the TX offload path.
Signed-off-by: NKittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kernel does its own validation of the IPv4 header checksum,
drivers/HW are not required to handle this.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This consolidates the checksum offload code that was duplicated
over the two qeth subdrivers.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial cleanup, in preparation for a subsequent patch.
Signed-off-by: NKittipon Meesompop <kmeesomp@linux.vnet.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct net_device contains a dev_port field. Store the OSA port number
in this field.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Reviewed-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing a VLAN ID on a L3 device, the driver currently attempts to
walk and unregister the VLAN device's IP addresses.
This can be safely removed - before qeth_l3_vlan_rx_kill_vid() even gets
called, we receive an inet[6]addr event for each IP on the device and
qeth_l3_handle_ip_event() unregisters the address accordingly.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the vid_list is only accessed from process context, there's no need to
protect it with a spinlock.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both qeth sub drivers use the same QDIO queue handlers, there's no need
to expose them via the driver's discipline. No functional change.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use hlist_entry_safe() instead of open-coding it.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pradeep Nalla says:

====================
liquidio: add support for ndo_get_stats64

Support ndo_get_stats64 instead of ndo_get_stats.  Also add stats for
multicast and broadcast packets.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support ndo_get_stats64 instead of ndo_get_stats.  Also add stats for
multicast and broadcast packets.
Signed-off-by: NPradeep Nalla <pradeep.nalla@cavium.com>
Acked-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To support the next patch in this series which has code that calls
octnet_get_link_stats from two different .c files, move that function (and
its dependency octnet_nic_stats_callback) to lio_core.c.  Remove
octnet_get_link_stats's static declaration and add its function prototype
in octeon_network.h.
Signed-off-by: NPradeep Nalla <pradeep.nalla@cavium.com>
Acked-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make PHYLIB boolean, because we reference phylib provided symbols now
from net/core/ethtool.c and therefore 'm' doesn't work.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: Extend availability of PHY statistics

This patch series adds support for retrieving PHY statistics with DSA switches
when the CPU port uses a PHY to PHY connection (as opposed to MAC to MAC).
To get there a number of things are done:

- first we move the code dealing with PHY statistics outside of net/core/ethtool.c
  and create helper functions since the same code will be reused
- then we allow network device drivers to provide an ethtool_get_phy_stats callback
  when the standard PHY library helpers are not suitable
- we update the DSA functions dealing with ethtool operations to get passed a
  stringset instead of assuming ETH_SS_STATS like they currently do
- then we provide a set of standard helpers within DSA as a framework and add
  the plumbing to allow retrieving the PHY statistics of the CPU port(s)
- finally plug support for retrieving such PHY statistics with the b53 driver

Changes in v3:

- retrict the b53 change to 539x and 531x5 series of switches
- added a change to dsa_loop.c to help test the feature

Changes in v2:

- got actual testing when the DSA master network device has a PHY that
  already provides statistics (thanks Nikita!)

- fixed the kbuild error reported when CONFIG_PHYLIB=n

- removed the checking of ops which is redundant and not needed
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We just return the same statistics through ethtool_get_stats() and
ethtool_get_phy_stats() for simplicity since this is just a mock-up driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the b53 driver to return PHY statistics when the CPU port used is
different than 5, 7 or 8, because those are typically PHY-less on most
devices. This is useful for debugging link problems between the switch
and an external host when using a non standard CPU port number (e.g: 4).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>