Add the device ID of the VF to the PCI device ID table.

Added a boolean flag is_vf in efx_nic_type to differentiate
between a VF and PF at probe time. This flag is useful in later
patches while setting MAC address specially in the
PCI-passthrough case.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow PFs to allocate shared RSS contexts if we exhaust our
exclusive RSS contexts. Make VFs use shared RSS contexts in
all cases.
Spruce up error handling so that the shadow copy of the RSS
table is updated after successful update, rather than in all
cases, so that we report the actual contents of the RSS table
after a failure to set it, rather than what we'd like it to be.

Populate context_size parameter when vacuously allocating RSS
context of size 1.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* Accept EPERM in some simple cases, the following cases are handled:
1) efx_mcdi_read_assertion()
Unprivileged PCI functions aren't allowed to GET_ASSERTS.
We return success as it's up to the primary PF to deal with asserts.
2) efx_mcdi_mon_probe() in efx_ef10_probe()
Unprivileged PCI functions aren't allowed to read sensor info, and
worrying about sensor data is the primary PF's job.
3) phy_op->reconfigure() in efx_init_port() and efx_reset_up()
Unprivileged functions aren't allowed to MC_CMD_SET_LINK, they just have
to accept the settings (including flow-control, which is what
efx_init_port() is worried about) they've been given.
4) Fallback to GET_WORKAROUNDS in efx_ef10_probe()
Unprivileged PCI functions aren't allowed to set workarounds. So if
efx_mcdi_set_workaround() fails EPERM, use efx_mcdi_get_workarounds()
to find out if workaround_35388 is enabled.
5) If DRV_ATTACH gets EPERM, try without specifying fw-variant
Unprivileged PCI functions have to use a FIRMWARE_ID of 0xffffffff
(MC_CMD_FW_DONT_CARE).
6) Don't try to exit_assertion unless one had fired
Previously we called efx_mcdi_exit_assertion even if
efx_mcdi_read_assertion had received MC_CMD_GET_ASSERTS_FLAGS_NO_FAILS.
This is unnecessary, and the resulting MC_CMD_REBOOT, even if the
AFTER_ASSERTION flag made it a no-op, would fail EPERM for unprivileged
PCI functions.
So make efx_mcdi_read_assertion return whether an assert happened, and only
call efx_mcdi_exit_assertion if it has.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To be able to use MC_CMD_VADAPTOR_SET_MAC, vadaptors must be
manually allocated and freed as automatic vadaptors will disappear
when their reference_count reaches zero, which must happen before
the MAC address is changed.

Vadaptors are allocated and freed in the vswitching_probe/remove
functions for PFs and VFs, and this means that vadaptors are restored
correctly following an MC reboot or other reset when required.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The parent PF creates vports for all its child VFs and adds MAC
addresses to these.  When the VF driver loads, it can make an MCDI
call to get the MAC address that the parent PF assigned it.

The parent PF also assigns a mac address to its own vport because
implicit creation of a vAdaptor will only work on evb ports with
MAC addresses assigned.

The vport MAC address needs to be stored in the PF's nic_data
struct as it can later be changed on the vadaptor (and its net_dev
struct). When removing a vport the original MAC address must be
deleted.

A new flag is needed in the VF data structure to identify whether
a vport has been assigned to the VF.  This is to determine whether
it needs to be un-assigned before freeing the vport.  Also,
attempting to un-assign a vport which is not assigned will result
in an EALREADY error.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added efx_nic_type structure for VF.
Mapped a different BAR for VF as it uses BAR 0 for memory.
Added functions sriov_init and sriov_fini.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use MC_CMD_GET_FUNCTION_INFO to record the PF number in nic_data.
This will be needed when assigned vports to VFs.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds functions to allocate and free vswitches and vports; vadaptors
are automatically allocated and freed when TX/RX queues are
initialised and finalised.  This vswitching structure is only created
if the firmware supports it, so a check that full-featured firmware
is running is performed first.

If the MC resets, the vswitching infrastructure will need to be
recreated, so mark the "must_probe_vswitching" flag when an MC reboot
is detected.

Don't try to create a vswitch if vf-count=0

This allocation of vswitches and vports does not currently support
configuring VLAN tags, but that can be added in a future change.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default port ID of EVB_PORT_ID_ASSIGNED is a "magic" number
for the MCFW to select the physical port of the PF.  If other
vswitches and vports are created on top of the default firmware
configuration, the ID of the newly created vport is then required
when passed to MCDI commands.  Currently, this doesn't happen so
the vport_id is never changed, but a subsequent patch will change
this behaviour so that other vswitches and vports are created.

The vport_id recorded in nic_data is only relevant for PFs.
VFs will have their vports created by their parent PF, and in
that case the parent PF will record the vport ID of each VF.
For a VF, nic_data->vport_id is expected to remain at the default
value.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The (future) code to add/remove vswitches and vports will be
dependent on the firmware variant.
To simplify the checking of the firmware variant, record
values for rx_dpcpu_fw_id and tx_dpcpu_fw_id in EF10 nic_data.

There was only one place where this was previously used:
efx_mcdi_print_fwver() in ethtool.c.
The MC_CMD_GET_CAPABILITIES can be replaced and the values from
nic_data used instead.

Note that the printing of "?" if the MC command fails or if the
outlength is incorrect no longer apply, because errors are returned
in efx_ef10_init_datapath_caps() in both of these cases.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TX_DOMAIN field is currently reserved but its safer to set
it to 0 for future compatibility.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the use of sriov_configure on EF10
to enable Virtual Functions while the driver is loaded.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The efx_vf struct contains Siena-specific fields for VFs,
so rename to siena_vf.
Also move it into the siena_nic_data struct, as EF10 will
track its VFs in its own ef10_nic_data, storing much less
information about them since VFDI is no longer used.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sfc: Own header for nic-specific sriov functions, single instance of netdev_ops and sriov removed from Falcon code

By putting all the efx_{siena,ef10}_sriov_* declarations in
{siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code.
Also fixes up an instance of this, where mcdi.c was calling
efx_siena_sriov_flr.

The single instance of netdev_ops should call general high level
functions that can then call something adapter specific in efx_nic_type.
We should only do adapter specialisation via efx_nic_type.

Removal of sriov functionality from the Falcon code means that tests
are needed for the presence of some callbacks.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
More Marvell DSA refactring and fixup

This patch setup continues the refactoring and cleanup of the Marvell
DSA drivers.

Patch #1 Centralizes the duplicated parts of port setup and global
setup into the shared mv88e6xxx.

Patch #2 Centralizes looping over the ports setting them up

Patch #3 Uses mnemonics for the remaining register access in the
drivers.

Patch #4 The 6172 is actually a member of the 6352 family. This moves
the probe code into the correct driver.

Patch #5 Adds more members of the 6171 family to the 6171 driver. The
new devices are untested.

Patch #6 The 6185 is a member of the 6131 family. Add it to the probe
code of the 6131 driver.

Patch #7 and Patch #8 Simply the mutex's in mv88e6xxx.c. The SMI bus
is the bottleneck, not the granularity of the mutex's so simply the
code down to a single mutex.

Patch #8 Fixes a false positive lockdep splat, due to nested uses of
MDIO busses.

Patch #9 Fixes another false positive lockdep splat with the transmit
queue because of stacked Ethernet devices.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSA stacks an Ethernet device on top of an Ethernet device. This can
cause false positive lockdep splats for the transmit queue:
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>

=============================================
[ INFO: possible recursive locking detected ]
4.0.0-rc7-01838-g70621a215fc7 #386 Not tainted
---------------------------------------------
kworker/0:0/4 is trying to acquire lock:
 (_xmit_ETHER#2){+.-...}, at: [<c040e95c>] sch_direct_xmit+0xa8/0x1fc

but task is already holding lock:
 (_xmit_ETHER#2){+.-...}, at: [<c03f4208>] __dev_queue_xmit+0x4d4/0x56c

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(_xmit_ETHER#2);
  lock(_xmit_ETHER#2);

To avoid this, walk the tq queues of the dsa slaves and set a lockdep
class.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSA can have nested MDIO busses, where the Ethernet MDIO bus is used
to access an MDIO bus within the switch which has the PHYs connected
to it. This nesting causes lockdep to give false positives. Use
mutex_lock_nested() to avoid this.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SMI bus is the bottleneck in all switch operations, not the
granularity of locks. Replace the stats mutex by the SMI mutex to make
the locking concept simpler.

The REG_READ/REG_WRITE macros cannot be used while holding the SMI
mutex, since they try to acquire it. Replace with calls to the
appropriate function which does not try to get the mutex.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SMI bus is the bottleneck in all switch operations, not the
granularity of locks. Replace the PHY mutex by the SMI mutex to make
the locking concept simpler.

The REG_READ/REG_WRITE macros cannot be used while holding the SMI
mutex, since they try to acquire it. Replace with calls to the
appropriate function which does not try to get the mutex.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6185 is part of the family that the mv88e6131 driver
supports. Add it to the probe function, and set the number of ports.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 6171 is one member of the family 6171/6175/6350/6351. Add the
other family members to the driver.

Not tested on these new devices.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6172 is part of the mv88e6352 family of devices. Move support
for it out of the mv88e6171 driver into the mv88e6352, which results
in some simplifications to the code.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use defines for registers, shifts and bits in the remaining register
accesses in the individual drivers, in order to aid readability.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that setting up a port is identical for all switches, centralisers
the code looping over all the ports to set them up.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port setup code in the individual drivers is identical for 6123,
6171, and 6352, and very similar in 6131. Move it all into mv88e6xxx,
using the chip families to differentiate on features.

Similarly, the global setup is also very similar. Move the majority
into mv8e6xxx.

The chips themselves fall into families. Add helpers which uses the
device IDs to determine if a device is a member of a family or not.
Add some additional device IDs to the existing list, to make these
helper functions more complete. However these IDs are not yet added to
the probe functions.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VXLAN must provide the skb mark and specifiy IPPROTO_UDP when doing
the FIB lookup for the remote ip. Otherwise an invalid route might
be returned.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch remove kernel-doc warnings.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Synchronize names with other drivers.
Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use of_property_* calls
Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use devm_* calls
Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Synchronize names with other drivers
Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is rule for network drivers with comments blocks
which is newly checked by checkpatch.pl script.
Let's fix it.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed checkpatch.pl errors and warnings.
Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds proper checks to handle the PHY-less case.
Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current implementation, jumbo frames are supported only
for the frame sizes > 16K. This patch corrects this logic to
handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame
MTU is within the limit of max frame size configured in the h/w
design.
Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The packet completion interrupts for TX and RX should be serviced before
the packets are consumed. This ensures against the degenerate case when a
new completion interrupt is raised after the handler has exited but before
the interrupts are cleared. In this case its possible for the ISR to clear
an unhandled interrupt (leading to potential deadlock).
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: NJason Wu <huanyu@xilinx.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AXI-DMA rx-delay interrupt can sometimes be triggered
when there are 0 outstanding packets received. This is due
to the fact that the receive function will greedily consume
as many packets as possible on interrupt. So if two packets
(with a very particular timing) arrive in succession they
will each cause the rx-delay interrupt, but the first interrupt
will consume both packets.
This means the second interrupt is a 0 packet receive.

This is mostly OK, except that the tail pointer register is
updated unconditionally on receive. Currently the tail pointer
is always set to the current bd-ring descriptor under
the assumption that the hardware has moved onto the next
descriptor. What this means for length 0 recv is the current
descriptor that the hardware is potentially yet to use will
be marked as the tail. This causes the hardware to think
its run out of descriptors deadlocking the whole rx path.

Fixed by updating the tail pointer to the most recent
successfully consumed descriptor.
Reported-by: NWendy Liang <wendy.liang@xilinx.com>
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: NJason Wu <huanyu@xilinx.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the RGMII. The h/w configuration
parameter C_PHY_TYPE, which represents the interface configured in
the design, is used to differentiate various interfaces supported
by AXI Ethernet.
Signed-off-by: NSrikanth Thokala <sthokal@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
Trivial fixes and changes for SGE

This patch series adds the following.
Discard packet if length is greater than MTU, move sge monitor code to a
new routine, add device node to ULD info, add congestion notification from
SGE for ingress queue and freelists and for T5, setting up the Congestion
Manager values of the new RX Ethernet Queue is done by firmware now.

This patch series has been created against net-next tree and includes
patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.

Thanks

V2: Align parenthesis for PATCH 2/6 and PATCH 5/6
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pktgen sends raw udp packets and bypasses most of the
linux networking stack. User can specify different packet sizes.
Hence we need to discard the packet if the length is greater than mtu
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>