DA9052/53 PMIC has capability to supply power for upto 3 banks of 6
white serial LEDS.  It can also control intensity of independent banks
and to drive these banks boost converter will provide up to 24V and
forward current of max 50mA.

This patch allows to control intensity of the individual WLEDs bank
through DA9052/53 PMIC.

This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for pandora (openpandora.org) backlight.

It might look like all this could be done using pwm_bl.c instead, but
there is a need of special programming sequence when turning on the LED
driver chip or else it will misbehave.  Doing this using pwm_bl.c would
require to use some register programming and pwm functions from platform
code, and ARM maintainers are allergic to driver-like code in /arch/arm
nowadays.  The PMIC PWM driver is currently missing too, so pwm_bl.c
can't be used anyway.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add backlight driver for Bachmann's ot200 visualisation device.  The
driver uses MFGPT 7 of CS5535 silicon to regulate the backlight.

[akpm@linux-foundation.org: remove redundant test of `brightness']
Signed-off-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Andres Salomon <dilinger@queued.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

THis driver supports TI LP8550/LP8551/LP8552/LP8553/LP8556 backlight
devices.

The brightness can be controlled by the I2C or PWM input.  The lp855x
driver provides both modes.  For the PWM control, pwm-specific functions
can be defined in the platform data.  And some information can be read
via the sysfs(lp855x device attributes).

For details, please refer to Documentation/backlight/lp855x-driver.txt.

[axel.lin@gmail.com: add missing mutex_unlock in lp855x_read_byte() error path]
[axel.lin@gmail.com: check platform data in lp855x_probe()]
[axel.lin@gmail.com: small cleanups]
[dan.carpenter@oracle.com: silence a compiler warning]
[axel.lin@gmail.com: use id->driver_data to differentiate lp855x chips]
[akpm@linux-foundation.org: simplify boolean return expression]
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Support for the Avionic Design Xanthos backlight device got added in
commit 3b96ea9e ("backlight: Add support for the Avionic Design Xanthos
backlight device.").  That support depends on ARCH_PXA_ADX.  The code that
should have provided that Kconfig symbol never got submitted.  It has
never been possible to even build this driver.  Remove it.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NThierry Reding <thierry.reding@avionic-design.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add backlight driver for AnalogicTech AAT2870.
Signed-off-by: NJin Park <jinyoungp@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add the ams369fg06 amoled panel driver.  The ams369fg06 amoled panel (480
x 800) driver uses 3-wired SPI inteface.  The brightness can be controlled
by gamma setting of amoled panel.

[sfr@canb.auug.org.au: fix build error]
[axel.lin@gmail.com: unregister backlight device when unloading the module]
[axel.lin@gmail.com: staticize ams369fg06_shutdown]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: anish singh <anish198519851985@gmail.com>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It works on hardware other than Macbook Pros, and it works on GPUs other
than Nvidia.  It should even work on iMacs, so change the name to match
reality more precisely and include an alias so existing users don't get
confused.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NRichard Purdie <richard.purdie@linuxfoundation.org>
Cc: Mourad De Clerck <mourad@aquazul.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver only has to deal with two different classes of hardware, but
right now it needs new DMI entries for every new machine. It turns out
that there's an ACPI device that uniquely identifies Apples with backlights,
so this patch reworks the driver into an ACPI one, identifies the hardware
by checking the PCI vendor of the root bridge and strips out all the DMI
code. It also changes the config text to clarify that it works on devices
other than Macbook Pros and GPUs other than nvidia.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NRichard Purdie <richard.purdie@linuxfoundation.org>
Cc: Mourad De Clerck <mourad@aquazul.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a ld9040 amoled panel driver.
Signed-off-by: NDonghwa Lee <dh09.lee@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds a backlight driver for controlling the pcf50633 LED module.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This is S6E63M0 AMOLED LCD Panel(480x800) driver using 3-wired SPI
interface also almost features for lcd panel driver has been implemented
in here.  and I added new structure common for all the lcd panel drivers
to include/linux/lcd.h file.

LCD Panel driver needs interfaces for controlling device power such as
power on/off and reset.  these interfaces are device specific so it should
be implemented to machine code at this time, we should create new
structure for registering these functions as callbacks and also a header
file for that structure and finally registered callback functions would be
called by lcd panel driver.  such header file(including new structure for
lcd panel) would be added for all the lcd panel drivers.

If anyone provides common structure for registering such callback
functions then we could reduce unnecessary header files for lcd panel.  I
thought that suitable anyone could be include/linux/lcd.h so a new
lcd_platform_data structure was added there.

[akpm@linux-foundation.org: coding-style fixes]
[randy.dunlap@oracle.com: fix s6e63m0 kconfig]
[randy.dunlap@oracle.com: fix device attribute functions return types]
Signed-off-by: NInKi Dae <inki.dae@samsung.com>
Reviewed-by: KyungMin Park <kyungmin.park.samsung.com>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The EP9307, EP9312, and EP9315 processors include a framebuffer
peripheral.  This peripheral has a dedicated pwm output called
BRIGHT that can be used to control the backlight on an LCD.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The ADP8860 combines a programmable backlight LED charge pump driver with
automatic phototransistor control.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The Epson LCD L4F00242T03 is mounted on the Freescale i.MX31 PDK board. 
Based upon Marek Vasut work in l4f00242t03.c, this driver provides
basic init and power on/off functionality for this device through the
sysfs lcd interface.

Unfortunately Datasheet for this device are not available and
all the control sequences sent to the display were copied from the
freescale driver that in the i.MX31 Linux BSP.

As in the i.MX31PDK board the core and io suppliers are voltage
regulators, that functionality is embedded here, but not strict.
Signed-off-by: NAlberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Enable max8925 backlight sub device.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

At most, three backlight device can be supported in 88pm860x driver.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

This patch adds support for the backlight device found on Avionic Design
Xanthos-based boards.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

ADd support for the SPI part of LMS283GF05 LCD.  The LCD uses SPI for
initialization and powerdown sequences.  No further defails are specified
in the datasheet about the initialization/powerdown sequence, just the
magic numbers that have to be sent over SPI bus.  This LCD can be found in
the Aeronix Zipit Z2 handheld.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

The WM831x series of PMICs provide DC-DC boost convertors and current
sinks which can be used together to drive LEDs for use as backlights.
Expose this functionality via the backlight API.

Since when used in this configuration the current sink and boost
convertor are very tightly coupled with a multi-stage startup for
the current sink which overlaps with the boost convertor startup
this driver bypasses the regulator API. Machine inititialisation
is responsible for ensuring that the regulators are not accessed
via both APIs.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Currently both da903x backlight and voltage reulator drivers have the
same name. Rename the backlight driver to allow use of both drivers as
modules.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NEric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The corgi backlight driver is really generic code. This rename makes
this a lot clearer and completes the partial rename made a while ago.
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

[akpm@linux-foundation.org: coding-style fixes]
[rpurdie@linux.intel.com: minor tweaks]
Signed-off-by: NClaudio Nieder <private@claudio.ch>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRichard Purdie <rpurdie@linux.intel.com>

On Sharp SL-6000 lcd/backlight is a bit complex, so add two drivers
one for lcd-driving chip, other one for dac regulating the backlight
LEDS.
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>

This type of LCD panel can be found on PXA3xx/Littleton platforms.
Add LCD device and SPI-based driver for this.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The driver is based on different source files including corgi_ssp.c,
corgi_lcd.c and corgi_bl.c, previously authored by Richard Purdie
and many others.

The LCD and Backlight device actually share the same SPI device, so
they are made into this single driver.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds a platform driver using the ATMEL PWM driver to control a
backlight which requires a PWM signal and optional GPIO signal for discrete
on/off signal.  It has been tested on Favr-32 board from EarthLCD.

The driver is configurable by supplying a struct with the platform data.  See
the include/linux/atmel-pwm-bl.h for details.

The board code for Favr-32 will be submitted to the AVR32 kernel list.
Signed-off-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a platform_lcd driver to allow boards with simple lcd power controls
to register themselves easily.

[akpm@linux-foundation.org: build fix]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide support for the ILI9320 display controller chip which is found in
many LCD displays.  Included with this is support for an example LCD using
this chip, the VGG2432A4.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Nvidia-based Apple Macbook Pros don't appear to handle backlight control
through the graphics card registers or ACPI, but instead trigger changes
via SMI calls. This driver registers a generic backlight device that
lets existing userspace deal with it. Code derived from Julien Blache's
Pommed application.
Signed-off-by: NJulien Blache <jb@jblache.org>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

Patch mostly from Eric Miao, with minor edits by rmk to convert
Eric's driver to a generic PWM-based backlight driver.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds the OMAP1 PWL-based LCD backlight driver.  It's been in the OMAP
tree for some time.  Note that OMAP2 can do similar things with the generic
timers which have PWM outputs.  Such timers are more generic than the PWL
found on OMAP1 chips, but have a different EMI profile because they aren't
driven by a pseudorandom number generator.

[akpm@linux-foundation.org: cleanups]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

This patch adds support for powering on and off the Samsung LTV350QV LCD
panel via SPI.  The driver responds to framebuffer power management, it
powers off the panel on reboot/halt/poweroff.  It can also be controlled
through sysfs.  The panel is powered up when the module is loaded, and off
when the module is unloaded.  Verified on AVR32 STK1000.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

Add the Intel Vermilion Range framebuffer support.
Signed-off-by: NAlan Hourihane <alanh@tungstengraphics.com>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add control of LCD backlight for Frontpath ProGear HX1050+.
Patch is based on http://downloads.sf.net/progear/progear-lcd-0.2.tar.gz
driver by M Schacht.
Signed-off-by: NMarcin Juszkiewicz <openembedded@hrw.one.pl>
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>