Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 22 5月, 2009 1 次提交
  3. 26 3月, 2008 1 次提交
  5. 11 12月, 2007 1 次提交
  7. 17 8月, 2007 2 次提交
  9. 26 7月, 2007 1 次提交
  11. 29 6月, 2007 1 次提交
  13. 14 6月, 2007 1 次提交
    • B
      [POWERPC] Rewrite IO allocation & mapping on powerpc64 · 3d5134ee
      由 Benjamin Herrenschmidt 提交于 
      This rewrites pretty much from scratch the handling of MMIO and PIO
space allocations on powerpc64.  The main goals are:

 - Get rid of imalloc and use more common code where possible
 - Simplify the current mess so that PIO space is allocated and
   mapped in a single place for PCI bridges
 - Handle allocation constraints of PIO for all bridges including
   hot plugged ones within the 2GB space reserved for IO ports,
   so that devices on hotplugged busses will now work with drivers
   that assume IO ports fit in an int.
 - Cleanup and separate tracking of the ISA space in the reserved
   low 64K of IO space. No ISA -> Nothing mapped there.

I booted a cell blade with IDE on PIO and MMIO and a dual G5 so
far, that's it :-)

With this patch, all allocations are done using the code in
mm/vmalloc.c, though we use the low level __get_vm_area with
explicit start/stop constraints in order to manage separate
areas for vmalloc/vmap, ioremap, and PCI IOs.

This greatly simplifies a lot of things, as you can see in the
diffstat of that patch :-)

A new pair of functions pcibios_map/unmap_io_space() now replace
all of the previous code that used to manipulate PCI IOs space.
The allocation is done at mapping time, which is now called from
scan_phb's, just before the devices are probed (instead of after,
which is by itself a bug fix). The only other caller is the PCI
hotplug code for hot adding PCI-PCI bridges (slots).

imalloc is gone, as is the "sub-allocation" thing, but I do beleive
that hotplug should still work in the sense that the space allocation
is always done by the PHB, but if you unmap a child bus of this PHB
(which seems to be possible), then the code should properly tear
down all the HPTE mappings for that area of the PHB allocated IO space.

I now always reserve the first 64K of IO space for the bridge with
the ISA bus on it. I have moved the code for tracking ISA in a separate
file which should also make it smarter if we ever are capable of
hot unplugging or re-plugging an ISA bridge.

This should have a side effect on platforms like powermac where VGA IOs
will no longer work. This is done on purpose though as they would have
worked semi-randomly before. The idea at this point is to isolate drivers
that might need to access those and fix them by providing a proper
function to obtain an offset to the legacy IOs of a given bus.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      3d5134ee
  15. 07 5月, 2007 1 次提交
  17. 13 4月, 2007 2 次提交
  19. 07 2月, 2007 1 次提交
  21. 24 1月, 2007 1 次提交
  23. 08 12月, 2006 1 次提交
  25. 04 12月, 2006 1 次提交
    • B
      [POWERPC] Make pci_read_irq_line the default · f90bb153
      由 Benjamin Herrenschmidt 提交于 
      This patch reworks the way IRQs are fixed up on PCI for arch powerpc.

It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().

It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.

I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.

I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      f90bb153
  27. 10 10月, 2006 2 次提交
  29. 26 9月, 2006 1 次提交
  31. 22 9月, 2006 2 次提交
    • N
      [POWERPC] Demacrofy arch/powerpc/platforms/maple/pci.c · cc9881ce
      由 Nathan Lynch 提交于 
      Noticed that the U3_*CFA macros have some typos:

#define U3_HT_CFA0(devfn, off)		\
		((((unsigned long)devfn) << 8) | offset)

(refers to offset rather than off)

#define U3_AGP_CFA0(devfn, off)	\
	((1 << (unsigned long)PCI_SLOT(dev_fn)) \
	| (((unsigned long)PCI_FUNC(dev_fn)) << 8) \

(refers to dev_fn rather than devfn)

Things happen to work, but there doesn't seem to be any reason these
shouldn't be functions.  Overall behavior should be unchanged.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      cc9881ce
    • N
      [POWERPC] Maple U3 HT - reject inappropriate config space access · d608df5c
      由 Nathan Lynch 提交于 
      When there is a PCI-X mode 2 capable device behind the HT<->PCI-X
bridge, the pci core decides that the device has the extended 4K
config space, even though the bus is not operating in mode 2.  This is
because the u3_ht pci ops silently accept offsets greater than 255 but
use only the 8 least significant bits, which means reading at offset
0x100 gets the data at offset 0x0, and causes confusion for lspci.

Reject accesses to configuration space offsets greater than 255.
Signed-off-by: NNathan Lynch <ntl@pobox.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      d608df5c
  33. 31 7月, 2006 1 次提交
  35. 03 7月, 2006 1 次提交
    • B
      [POWERPC] Add new interrupt mapping core and change platforms to use it · 0ebfff14
      由 Benjamin Herrenschmidt 提交于 
      This adds the new irq remapper core and removes the old one.  Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).

This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.

For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259.  That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.

The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      0ebfff14
  37. 28 6月, 2006 1 次提交
  39. 22 4月, 2006 1 次提交
  41. 24 2月, 2006 1 次提交
  43. 15 1月, 2006 1 次提交
  45. 16 11月, 2005 1 次提交
    • B
      [PATCH] powerpc: pci_64 fixes & cleanups · b5166cc2
      由 Benjamin Herrenschmidt 提交于 
      I discovered that in some cases (PowerMac for example) we wouldn't
properly map the PCI IO space on recent kernels. In addition, the code
for initializing PCI host bridges was scattered all over the place with
some duplication between platforms.

This patch fixes the problem and does a small cleanup by creating a
pcibios_alloc_controller() in pci_64.c that is similar to the one in
pci_32.c (just takes an additional device node argument) that takes care
of all the grunt allocation and initialisation work. It should work for
both boot time and dynamically allocated PHBs.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      b5166cc2
  47. 10 11月, 2005 1 次提交
    • B
      [PATCH] ppc64: fix PCI IO mapping · 0f34f490
      由 Benjamin Herrenschmidt 提交于 
      phbs_remap_io(), which maps the PCI IO space into the kernel virtual space,
is called too early on powermac, and thus doesn't work.

This fixes it by removing the call from all platforms and putting it back
into the ppc64 common code where it belongs, after the actual probing of
the bus.

That means that before that call, only the ISA IO space (if any) is mapped,
any PIO access (from quirks for example) will fail. This happens not to be
a problem for now, but we'll have to rework that code if it becomes one in
the future.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      0f34f490
  49. 29 10月, 2005 1 次提交
  51. 22 10月, 2005 1 次提交
  53. 20 10月, 2005 1 次提交
  55. 28 9月, 2005 1 次提交
  57. 12 9月, 2005 1 次提交
  59. 09 9月, 2005 1 次提交
    • P
      [PATCH] Separate pci bits out of struct device_node · 1635317f
      由 Paul Mackerras 提交于 
      This patch pulls the PCI-related junk out of struct device_node and
puts it in a separate structure, struct pci_dn.  The device_node now
just has a void * pointer in it, which points to a struct pci_dn for
nodes that represent PCI devices.  It could potentially be used in
future for device-specific data for other sorts of devices, such as
virtual I/O devices.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      1635317f
  61. 17 4月, 2005 1 次提交
    • L
      Linux-2.6.12-rc2 · 1da177e4
      由 Linus Torvalds 提交于 
      Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
      1da177e4