This patch supplies the Mailbox Controller nodes.  In order to
request channels, these nodes will be referenced by Mailbox
Client nodes.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

This is used for CPU Frequency Scaling.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Used for Voltage Scaling using CPUFreq.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

You'll notice that the voltage cell is populated with 0's.  Voltage
information is very platform specific, even depends on 'cut' and
'substrate' versions.  Thus it is left blank for a generic (safe)
implementation.  If other nodes/properties are provided by the
bootloader, the ST CPUFreq driver will over-ride these generic
values.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

STiH407 family uses the Synopsys IP.
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Now we have default pinconfig groups for each SPI
controller ensure it is used by the SPI controller
node.
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The display nodes are common to both STiH407 and STiH410, move them to the
family file.
Acked-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The PWM may not be used on some boards, so enable them only the board file.
Acked-by: NPatrice Chotard <patrice.chotard@st.com>
Acked-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

By popular vote, the DT binding includes for reset controllers are located
in include/dt-bindings/reset/. Move the STi reset constants in there, too,
to avoid confusion.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NPatrice Chotard <patrice.chotard@st.com>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

This also incorporates the STiH410.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

To enable SMP when booting via u-boot we need to specify the
newly implemented cpu-release-addr DT property.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

This driver is used to enable System Configuration Register controlled
External, CTI (Core Sight), PMU (Performance Management), and PL310 L2
Cache IRQs prior to use.

Here we are enabling PMU IRQs on both channels.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

This is ARM's generic Performance Monitoring Unit.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Now that both usb2 and usb3 phy drivers, and also the ST dwc3 glue code
are all present upstream, we can add the dwc3 DT node and have a working
usb3 controller on stih407-b2120 and stih410-b2020.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Ths picophyreset is incorrectly defined, which stops the usb2 phy being
taken out of reset.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Now that the miphy28lp is upstream, we can add the sata dt nodes
for stih407 family silicon. This has been tested on b2120 board
J4 (sata0 channel). These nodes are disabled by default as a
special mini pci-e to sata daughter board is required which
isn't shipped with the board.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

On current ST platforms the LPC controls a number of functions.  This
patch enables support for the LPC Watchdog and LPC RTC devices on LPC1
and LPC2 respectively.
Signed-off-by: NDavid Paris <david.paris@st.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The nodes have been split to allow as much commonality as possible.
The stih407 has a silicon bug with eMMC UHS modes (with top regs)
and as such doesn't have any of the uhs dt properties.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The Synchronous Serial Controller is used to provide SPI.

These are the ports which are located on the Stand-By Controller (SBC).
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The Synchronous Serial Controller is used to provide SPI.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The MiPHY28lp is a Generic PHY which can serve various SATA, PCIe or
USB3 devices. The two first ports can be use for either; both SATA, both
PCIe or one of each in any configuration.
The Third port is only for USB3.
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

This patch adds the dt nodes for the usb2 picophy found on the stih407
device family. It is used on stih407 by the dwc3 usb3 controller when
controlling usb2/1.1 devices.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the dt nodes for the usb2 picophy found on the stih407
device family. It is used on stih407 by the dwc3 usb3 controller when
controlling usb2/1.1 devices.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The stih410 soc which will be added in the following commit is very similar to
the stih407, to enable maximum re-use of the dt files this commit abstracts the
common parts into a shared dt file stihxxx-b2120 for the board, and also a shared
file stih407-family.dtsi for the SoC.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Patch adds DT entries for clockgen C0
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: NOlivier Bideau <olivier.bideau@st.com>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

This patch adds the reset controller DT nodes for the powerdown,
 softreset and picophy controllers.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The STiH407 is advanced multi-HD AVC processor with 3D graphics acceleration
and 1.5-GHz ARM Cortex-A9 SMP CPU.
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>