VolumeKnob is present on most sigmatel codecs, it allows to decrease
volume of all DACs at once, it is a kind of post-procesing volume.
Note that all output amps of sigmatel only decrease volume, and all
input amps only increase volume.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The analog loopback routes the sound just before it enters ADC0
to output of DAC0.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Center/LFE channels are located on same jack, so it can be usefull
to swap them.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Comment in hda_intel.c states that 'the explicit resume is needed only
when POWER_SAVE isn't set', but this is not true.
There is no code that will automaticly power up the codec on resume,
but only code that powers it up when user accesses it. So if user
leaves a sound playing, codec will not be powered
To fix that I check if there are any codecs that should be powered
codec->power_count, and if so I power them up together with main
controller.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

codec->power_transition is supposed to be true while codec is going
to be shut off if in the mean time somebody calls snd_hda_power_up,
hda_power_work will not shut down the codec, but nether will clear
codec->power_transition, thus it stays on forever. Fix this.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The '-MCx' suffix that is expected by alsa-lib is only needed in the
card driver string, so we can show the actual chip name in the
shortname.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Check that the UART_EN bit actually enabled the MPU-401 port.
Apparently, C-Media thinks that it is a good idea to be paranoid here.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Integrated MPU-401/OPL3 ports are available with chip version 39 and
later, so we do not test for the port with version 37.
Now that the test is known to work, we can again enable the MIDI port by
default.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Add support for 88.2 kHz and 96 kHz analog and digital playback on
CMI8768/CMI8770 chips.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Remove the constraint that sets the channel limit for the first playback
device to that of the second one; the first device supports only stereo.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The STAC codes adds line_out_pins[] for shared mic/line-inputs accordingly.
But, the current code may give a hole with NID=0 in some setting, which
results in an error at probe.  This patch fixes the problem.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The resume procedure for STAC codecs overrides the cached values and
results in the wrong (reset) PIN state.  The patch gets rid of the
overriding part and simplifies the resume.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Allow the interface's mixer to be used, and give the interface its
correct name.
Signed-off-by: NMark Hills <mark@pogo.org.uk>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Clean up the mixer entries for Input Source using a macro.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Fix the index for Front Mic capture source on ALC262 HP machines.
Also, added the new capture source list for HP BPC DC7000 series
to work properly.
From: zhejiang <zhe.jiang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

added support for the latest revision of the 9632 (and hopefully a few
following ones). The DSP matrix was not working because of wrong
identification of the card in this part of the code.
Signed-off-by: NRemy Bruno <remy.bruno@trinnov.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

* better report of speed mode change failures
* autosync_ref control bugfix (was reporting pref_sync_ref instead)
  (changed HDSPM_AES32_AUTOSYNC_FROM_NONE value to comply with array
  indexing in snd_hdspm_info_autosync_ref())
* added support for master modes up to 192kHz (clock source control
  value was restricted up to 96kHz)
Signed-off-by: NRemy Bruno <remy.bruno@trinnov.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

usb_set_interface() can fail, even for altsetting 0
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Add a quirk to detect the Serato Scratch Live DJ Box.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

On codec chips with both audio and modem functions (e.g. Conexant one),
performing AC97_RESET resets the whole registers.  When both audio and
modem drivers are resumed at the same time, the modem one often is
resumed after the audio, and it results in the reset of audio registers
(ALSA bug#3333).
This patch fixes such a problem.  Since the modem codec basically
doesn't need AC97_RESET, skip this initialization unless specified
as audio.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Some codecs need Mic Boost mixer controls for obtaining a proper recording
level, but the auto-configuration doesn't create them.
This patch adds the creation of mic-boost controls on corresponding codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

CS5530 is a PCI device and often shares the IRQ although the SB common
routine tries to allocate it exclusively.  This patch allows shared IRQ
for CS5530.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

vmalloc() returns void *. no need to cast.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Show the actual name of CMI8762/CMI8768/CMI8769/CMI8770 chips in the
card longname instead of just using 'CMI8738' for all of them.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Remove the has_dual_dac variable because it was always set.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Add a case for chip version 39 where no bit is set in register 0Ch, and
move the detection of version 39 before that of 8768.  This makes the
logic more compatible with the driver on that other OS.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Unused bytes in the I/O register range are likely to have the value 0x00
instead of 0xff, so test against both values when checking for the
presence of the integrated MIDI port.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Fixed Dell laptops support with STAC92xx codecs.
Many pin-config models are introduced.  See ALSA-Configuration.txt
for details.
The patch taken from ALSA bug#3319, originally by Jorg Prante:
	https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3319Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

The unsol event of ALC268 is in the standard bit 26.
Also, fixed the Acer master controls, and added Extensa 5210
to the quirk list.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Fixed the master mixer switch of ALC272 sony-amd model.
It used a simple bind-control, but it resulted in unexpected
unmute of speaker output.  Now the control checks the HP jack
state apropriately, just like fujitsu model.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

gcc-3.x doesn't like forward inlining:
  CC [M]  sound/pci/hda/hda_codec.o
sound/pci/hda/hda_codec.c: In function 'snd_hda_codec_free':
sound/pci/hda/hda_codec.c:517: sorry, unimplemented: inlining failed in call to 'free_hda_cache': function body not available
sound/pci/hda/hda_codec.c:534: sorry, unimplemented: called from here
sound/pci/hda/hda_codec.c:517: sorry, unimplemented: inlining failed in call to 'free_hda_cache': function body not available
sound/pci/hda/hda_codec.c:535: sorry, unimplemented: called from here
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added the PCI ID entries for known working devices
- Prolink PixelView PV-M4900
- Pinnacle  Studio PCTV rave
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Make sure that the MPU-401 MIDI and OPL-3 FM devices are used only on
those chips where they are supported, and that the correct port
addresses are used.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Use the standard firmware loader for loading ICS2115 OS firmware file.
This is the last old bad guy that is still using sys_open() and sys_read()
calls, and now all should be gone.
The patch also adds the missing description of module options related
with wavefront_synth.c.
Due to this rewrite, user will have to copy or make symlink the firmware
file appropriately to the standard firmware path such as /lib/firmware.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Added missing capture boost controls for ALC268 codec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Initialize card->shortname early enough so that the MIDI device can pick
it up and does not need to have a generic name.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Force low speed USB MIDI devices like the ESI MIDI Mate and RomIO II to
use interrupt transfers because the USB core would not be happy about
low speed bulk transfers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Allow low speed MIDI devices because newer devices from ESI do not
support full speed.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Allow output interrupt transfers for some MIDI devices that require
them.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>

Some Fujitsu laptops have SPDIF output jack (ALSA bug#3009).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@suse.cz>