[ Upstream commit 8159ecab0db9095902d4c73605fb8787f5c7d653 ]

Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.

The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.

A message is logged when the above scenario occurs:

  macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor

Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.

This issue was observed on a ZynqMP based system.

Fixes: 4df95131 ("net/macb: change RX path for GEM")
Signed-off-by: NAnssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e100a897bf9b19089e57f236f2398c9e0538900e ]

64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.

The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.

Fix that by adding the necessary DMA memory barrier between the writes.

This corruption was observed on a ZynqMP based system.

Fixes: fff8019a ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: NAnssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: NHarini Katakam <harini.katakam@xilinx.com>
Tested-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f07d4276892d97671e880190ff195a288b2d8d92 ]

We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.

Fixes: d2201a21 ("qed: No need for LL2 frags indication")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cf76785d30712d90185455e752337acdb53d2a5d ]

Ensure that we clear XPRT_CONNECTING before releasing the XPRT_LOCK so that
we don't have races between the (asynchronous) socket setup code and
tasks in xprt_connect().
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a50e5fb8db83c5b57392204c21ea6c5c4ccefde6 ]

Recently TXQ teardown was moved earlier in ieee80211_unregister_hw(),
to avoid a use-after-free of the netdev data. However, interfaces
aren't fully removed at the point, and cfg80211_shutdown_all_interfaces
can for example, TX a deauth frame. Move the TXQ teardown to the
point between cfg80211_shutdown_all_interfaces and the free of
netdev queues, so we can be sure they are torn down before netdev
is freed, but after there is no ongoing TX.

Fixes: 77cfaf52 ("mac80211: Run TXQ teardown code before de-registering interfaces")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6adafc356e20189193b38ee6b9af7743078bf6b4 ]

Create a net bridge, add eth and vnet to the bridge. The vnet is used
by a virtual machine. When ping the virtual machine from the outside
host and the virtual machine send multicast at the same time, the ping
package will lost.

The multicast package send to the eth, eth will send it to the bridge too,
and the bridge learn the mac of eth. When outside host ping the virtual
mechine, it will match the promisc entry of the eth which is not expected,
and the bridge send it to eth not to vnet, cause ping lost.

So this patch change promisc tcam entry position to the END of 512 tcam
entries, which indicate lower priority. And separate one promisc entry to
two: mc & uc, to avoid package match the wrong tcam entry.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 726ae5c9e5f0c18eca8ea5296b526242c3e89822 ]

In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.

Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7e74a19ca522aec7c2be201a7ae1d1d57ded409b ]

The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a57275d35576fdd89d8c771eedf1e7cf97e0dfa6 ]

There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.

So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.

When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c82bd077e1ba3dd586569c733dc6d3dd4b0e43cd ]

1.In "hns_nic_init_irq", if request irq fail at index i,
  the function return directly without releasing irq resources
  that already requested.

2.In "hns_nic_net_up" after "hns_nic_init_irq",
  if exceptional branch occurs, irqs that already requested
  are not release.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 31f6b61d810654fb3ef43f4d8afda0f44b142fad ]

If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.

This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5778b13b64eca5549d242686f2f91a2c80c8fa40 ]

After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.

Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
         BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
         smp_mb__before_clear_bit();
         clear_bit(NAPI_STATE_SCHED, &n->state);
}

[37255.571996] Kernel panic - not syncing: BUG!
[37255.595234] Call trace:
[37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0
[37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28
[37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8
[37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c
[37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0
[37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c
[37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168
[37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c
[37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68
[37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704
[37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4
[37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84
[37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c
[37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618
[37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4
[37255.801139] SMP: stopping secondary CPUs
[37255.805079] kbox: catch panic event.
[37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072
[37255.816103] flush cache 0xffff80003f000000  size 0x800000
[37255.822192] flush cache 0xffff80003f000000  size 0x800000
[37255.828289] flush cache 0xffff80003f000000  size 0x800000
[37255.834378] kbox: no notify die func register. no need to notify
[37255.840413] ---[ end Kernel panic - not syncing: BUG!

This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4ad26f117b6ea0f5d5f1592127bafb5ec65904d3 ]

According to the hip06 datasheet:
1.Six registers use wrong address:
  RCB_COM_SF_CFG_INTMASK_RING
  RCB_COM_SF_CFG_RING_STS
  RCB_COM_SF_CFG_RING
  RCB_COM_SF_CFG_INTMASK_BD
  RCB_COM_SF_CFG_BD_RINT_STS
  DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
  0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
  is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
  overwrite

These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 308c6cafde0147616da45e3a928adae55c428deb ]

There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
   and install them again, must use "ifconfig down/ifconfig up"
   command pair to bring port to work.

   This patch calls phy_stop function when init phy to fix this bug.

2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
   all ports can not use anymore, because of the phy devices register
   failed(phy devices already exists).

   Phy devices are registered when hns_dsaf installed, this patch
   removes them when hns_dsaf removed.

The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4e1d4be681b2c26fd874adbf584bf034573ac45d ]

According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 51367e423c6501a26e67d91a655d2bc892303462 ]

The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:

WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init

Remove the __init to make it always do the right thing.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6c0563e442528733219afe15c749eb2cc365da3f ]

create_ctx is called from tls_init and tls_hw_prot
hence initialize function pointers in common routine.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2ab4c3426c0cf711d7147e3f559638e4ab88960e ]

Clang warns:

drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
                                   ^
1 warning generated.

Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c629421a990033ba539eb8585e73a2e6fa9ea631 ]

Need to be able to boot without PCI devices present.
Signed-off-by: NSinan Kaya <okaya@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7c250f4612ae97aa04500c0d0cff69bb87046e3a ]

Starting from mac80211 commit adf8ed01e4fd ("mac80211: add an optional
TXQ for other PS-buffered frames") and commit 0eeb2b674f05 ("mac80211:
add an option for station management TXQ") a new per-sta queue has been
introduced for bufferable management frames.
sta->txq[IEEE80211_NUM_TIDS] is initialized just if the driver reports
the following hw flags:
- IEEE80211_HW_STA_MMPDU_TXQ
- IEEE80211_HW_BUFF_MMPDU_TXQ
This can produce a NULL pointer dereference in mt76_stop_tx_queues
since mt76 iterates on all available sta tx queues assuming they are
initialized by mac80211. This issue has been spotted analyzing the code
(it has not triggered any crash yet)
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9e6371d3c6913ff1707fb2c0274c9925f7aaef80 ]

Add missing spin_lock_init() for cdev->np_lock.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 801df68d617e3cb831f531c99fa6003620e6b343 ]

csk leak can happen if a new TCP connection gets established after
cxgbit_accept_np() returns, to fix this leak free remaining csk in
cxgbit_free_np().
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9061193c4ee065d3240fde06767c2e06ec61decc ]

Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 04f05230c5c13b1384f66f5186a68d7499e34622 ]

Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit bbf666c1af916ed74795493c564df6fad462cc80 ]

On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d4e7df16567b80836a78d31b42f1a9355a636d67 ]

rbnode in insert_tree() is rcu protected pointer.
So, in order to handle this pointer, _rcu function should be used.
rb_link_node_rcu() is a rcu version of rb_link_node().

Fixes: 34848d5c ("netfilter: nf_conncount: Split insert and traversal")
Signed-off-by: NTaehee Yoo <ap420073@gmail.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 542fbda0f08f1cbbc250f9e59f7537649651d0c8 ]

The dst entry might already have a zero refcount, waiting on rcu list
to be free'd.  Using dst_hold() transitions its reference count to 1, and
next dst release will try to free it again -- resulting in a double free:

  WARNING: CPU: 1 PID: 0 at include/net/dst.h:239 nf_xfrm_me_harder+0xe7/0x130 [nf_nat]
  RIP: 0010:nf_xfrm_me_harder+0xe7/0x130 [nf_nat]
  Code: 48 8b 5c 24 60 65 48 33 1c 25 28 00 00 00 75 53 48 83 c4 68 5b 5d 41 5c c3 85 c0 74 0d 8d 48 01 f0 0f b1 0a 74 86 85 c0 75 f3 <0f> 0b e9 7b ff ff ff 29 c6 31 d2 b9 20 00 48 00 4c 89 e7 e8 31 27
  Call Trace:
  nf_nat_ipv4_out+0x78/0x90 [nf_nat_ipv4]
  nf_hook_slow+0x36/0xd0
  ip_output+0x9f/0xd0
  ip_forward+0x328/0x440
  ip_rcv+0x8a/0xb0

Use dst_hold_safe instead and bail out if we cannot take a reference.

Fixes: a4c2fd7f ("net: remove DST_NOCACHE flag")
Reported-by: NMartin Zaharinov <micron10@gmail.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 708abf74dd87f8640871b814faa195fb5970b0e3 ]

In the error handling block, nla_nest_cancel(skb, atd) is called to
cancel the nest operation. But then, ipset_nest_end(skb, atd) is
unexpected called to end the nest operation. This patch calls the
ipset_nest_end only on the branch that nla_nest_cancel is not called.

Fixes: 45040978 ("netfilter: ipset: Fix set:list type crash when flush/dump set in parallel")
Signed-off-by: NPan Bian <bianpan2016@163.com>
Signed-off-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 96d1a731611f711f0cb82cea93363ae2ea8cb028 ]

When the VF driver does a reset, it (at least the Linux one) writes to
the VFCTRL register to issue a reset and then immediately sends a reset
message using the mailbox API. This is racy because when the PF driver
detects that the VFCTRL register reset pin has been asserted, it clears
the mailbox memory. Depending on ordering, the reset message sent by
the VF could be cleared by the PF driver. It then responds to the
cleared message with a NACK which causes the VF driver to malfunction.
Fix this by deferring clearing the mailbox memory until the reset
message is received.

Fixes: 939b701a ("ixgbe: fix driver behaviour after issuing VFLR")
Signed-off-by: NRoss Lagerwall <ross.lagerwall@citrix.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 158daed16efb1170694e420ae06ba8ba954d82e5 ]

A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().

Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.

Fixes: 458867b2 ("i40e: don't remove netdev->dev_addr when syncing uc list")
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 254eb5505ca0ca749d3a491fc6668b6c16647a99 ]

The LDT remap placement has been changed. It's now placed before the direct
mapping in the kernel virtual address space for both paging modes.

Change address markers order accordingly.

Fixes: d52888aa2753 ("x86/mm: Move LDT remap out of KASLR region on 5-level paging")
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: bhe@redhat.com
Cc: hans.van.kranenburg@mendix.com
Cc: linux-mm@kvack.org
Cc: xen-devel@lists.xenproject.org
Link: https://lkml.kernel.org/r/20181130202328.65359-3-kirill.shutemov@linux.intel.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 16877a5570e0c5f4270d5b17f9bab427bcae9514 ]

There is a guard hole at the beginning of the kernel address space, also
used by hypervisors. It occupies 16 PGD entries.

This reserved range is not defined explicitely, it is calculated relative
to other entities: direct mapping and user space ranges.

The calculation got broken by recent changes of the kernel memory layout:
LDT remap range is now mapped before direct mapping and makes the
calculation invalid.

The breakage leads to crash on Xen dom0 boot[1].

Define the reserved range explicitely. It's part of kernel ABI (hypervisors
expect it to be stable) and must not depend on changes in the rest of
kernel memory layout.

[1] https://lists.xenproject.org/archives/html/xen-devel/2018-11/msg03313.html

Fixes: d52888aa2753 ("x86/mm: Move LDT remap out of KASLR region on 5-level paging")
Reported-by: NHans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NHans van Kranenburg <hans.van.kranenburg@mendix.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: bhe@redhat.com
Cc: linux-mm@kvack.org
Cc: xen-devel@lists.xenproject.org
Link: https://lkml.kernel.org/r/20181130202328.65359-2-kirill.shutemov@linux.intel.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8e41cae64b08fe2e86a9ffb88b295c6b4b3a3322 ]

gcc warning this:

drivers/net/ieee802154/ca8210.c:730:10: warning:
 comparison is always false due to limited range of data type [-Wtype-limits]

'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.

Fixes: ded845a7 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1d1bbc37f89b0559c9e913682f2489d89cfde6b8 ]

ibmvnic_reset allocated new reset work item objects in a non-atomic
context. This can be called from a tasklet, generating the output below.
Allocate work items with the GFP_ATOMIC flag instead.

BUG: sleeping function called from invalid context at mm/slab.h:421
in_atomic(): 1, irqs_disabled(): 1, pid: 93, name: kworker/0:2
INFO: lockdep is turned off.
irq event stamp: 66049
hardirqs last  enabled at (66048): [<c000000000122468>] tasklet_action_common.isra.12+0x78/0x1c0
hardirqs last disabled at (66049): [<c000000000befce8>] _raw_spin_lock_irqsave+0x48/0xf0
softirqs last  enabled at (66044): [<c000000000a8ac78>] dev_deactivate_queue.constprop.28+0xc8/0x160
softirqs last disabled at (66045): [<c0000000000306e0>] call_do_softirq+0x14/0x24
CPU: 0 PID: 93 Comm: kworker/0:2 Kdump: loaded Not tainted 4.20.0-rc6-00001-g1b50a8f03706 #7
Workqueue: events linkwatch_event
Call Trace:
[c0000003fffe7ae0] [c000000000bc83e4] dump_stack+0xe8/0x164 (unreliable)
[c0000003fffe7b30] [c00000000015ba0c] ___might_sleep+0x2dc/0x320
[c0000003fffe7bb0] [c000000000391514] kmem_cache_alloc_trace+0x3e4/0x440
[c0000003fffe7c30] [d000000005b2309c] ibmvnic_reset+0x16c/0x360 [ibmvnic]
[c0000003fffe7cc0] [d000000005b29834] ibmvnic_tasklet+0x1054/0x2010 [ibmvnic]
[c0000003fffe7e00] [c0000000001224c8] tasklet_action_common.isra.12+0xd8/0x1c0
[c0000003fffe7e60] [c000000000bf1238] __do_softirq+0x1a8/0x64c
[c0000003fffe7f90] [c0000000000306e0] call_do_softirq+0x14/0x24
[c0000003f3967980] [c00000000001ba50] do_softirq_own_stack+0x60/0xb0
[c0000003f39679c0] [c0000000001218a8] do_softirq+0xa8/0x100
[c0000003f39679f0] [c000000000121a74] __local_bh_enable_ip+0x174/0x180
[c0000003f3967a60] [c000000000bf003c] _raw_spin_unlock_bh+0x5c/0x80
[c0000003f3967a90] [c000000000a8ac78] dev_deactivate_queue.constprop.28+0xc8/0x160
[c0000003f3967ad0] [c000000000a8c8b0] dev_deactivate_many+0xd0/0x520
[c0000003f3967b70] [c000000000a8cd40] dev_deactivate+0x40/0x60
[c0000003f3967ba0] [c000000000a5e0c4] linkwatch_do_dev+0x74/0xd0
[c0000003f3967bd0] [c000000000a5e694] __linkwatch_run_queue+0x1a4/0x1f0
[c0000003f3967c30] [c000000000a5e728] linkwatch_event+0x48/0x60
[c0000003f3967c50] [c0000000001444e8] process_one_work+0x238/0x710
[c0000003f3967d20] [c000000000144a48] worker_thread+0x88/0x4e0
[c0000003f3967db0] [c00000000014e3a8] kthread+0x178/0x1c0
[c0000003f3967e20] [c00000000000bfd0] ret_from_kernel_thread+0x5c/0x6c
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6c5c7489089608d89b7ce310bca44812e2b0a4a5 ]

ibmvnic_reset can create and schedule a reset work item from
an IRQ context, so do not use a mutex, which can sleep. Convert
the reset work item mutex to a spin lock. Locking debugger generated
the trace output below.

BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908
in_atomic(): 1, irqs_disabled(): 1, pid: 120, name: kworker/8:1
4 locks held by kworker/8:1/120:
 #0: 0000000017c05720 ((wq_completion)"events"){+.+.}, at: process_one_work+0x188/0x710
 #1: 00000000ace90706 ((linkwatch_work).work){+.+.}, at: process_one_work+0x188/0x710
 #2: 000000007632871f (rtnl_mutex){+.+.}, at: rtnl_lock+0x30/0x50
 #3: 00000000fc36813a (&(&crq->lock)->rlock){..-.}, at: ibmvnic_tasklet+0x88/0x2010 [ibmvnic]
irq event stamp: 26293
hardirqs last  enabled at (26292): [<c000000000122468>] tasklet_action_common.isra.12+0x78/0x1c0
hardirqs last disabled at (26293): [<c000000000befce8>] _raw_spin_lock_irqsave+0x48/0xf0
softirqs last  enabled at (26288): [<c000000000a8ac78>] dev_deactivate_queue.constprop.28+0xc8/0x160
softirqs last disabled at (26289): [<c0000000000306e0>] call_do_softirq+0x14/0x24
CPU: 8 PID: 120 Comm: kworker/8:1 Kdump: loaded Not tainted 4.20.0-rc6 #6
Workqueue: events linkwatch_event
Call Trace:
[c0000003fffa7a50] [c000000000bc83e4] dump_stack+0xe8/0x164 (unreliable)
[c0000003fffa7aa0] [c00000000015ba0c] ___might_sleep+0x2dc/0x320
[c0000003fffa7b20] [c000000000be960c] __mutex_lock+0x8c/0xb40
[c0000003fffa7c30] [d000000006202ac8] ibmvnic_reset+0x78/0x330 [ibmvnic]
[c0000003fffa7cc0] [d0000000062097f4] ibmvnic_tasklet+0x1054/0x2010 [ibmvnic]
[c0000003fffa7e00] [c0000000001224c8] tasklet_action_common.isra.12+0xd8/0x1c0
[c0000003fffa7e60] [c000000000bf1238] __do_softirq+0x1a8/0x64c
[c0000003fffa7f90] [c0000000000306e0] call_do_softirq+0x14/0x24
[c0000003f3f87980] [c00000000001ba50] do_softirq_own_stack+0x60/0xb0
[c0000003f3f879c0] [c0000000001218a8] do_softirq+0xa8/0x100
[c0000003f3f879f0] [c000000000121a74] __local_bh_enable_ip+0x174/0x180
[c0000003f3f87a60] [c000000000bf003c] _raw_spin_unlock_bh+0x5c/0x80
[c0000003f3f87a90] [c000000000a8ac78] dev_deactivate_queue.constprop.28+0xc8/0x160
[c0000003f3f87ad0] [c000000000a8c8b0] dev_deactivate_many+0xd0/0x520
[c0000003f3f87b70] [c000000000a8cd40] dev_deactivate+0x40/0x60
[c0000003f3f87ba0] [c000000000a5e0c4] linkwatch_do_dev+0x74/0xd0
[c0000003f3f87bd0] [c000000000a5e694] __linkwatch_run_queue+0x1a4/0x1f0
[c0000003f3f87c30] [c000000000a5e728] linkwatch_event+0x48/0x60
[c0000003f3f87c50] [c0000000001444e8] process_one_work+0x238/0x710
[c0000003f3f87d20] [c000000000144a48] worker_thread+0x88/0x4e0
[c0000003f3f87db0] [c00000000014e3a8] kthread+0x178/0x1c0
[c0000003f3f87e20] [c00000000000bfd0] ret_from_kernel_thread+0x5c/0x6c
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ca5047286c9c93a01e1f471d00a6019536992954 ]

Before commit 7fd6d98b ("i2c: i801: Allow ACPI AML access I/O
ports not reserved for SMBus"), enabling RMI on the T560 would cause
the touchpad to stop working after resuming from suspend. Now that
this issue is fixed, RMI can be enabled safely and works fine.
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NYussuf Khalil <dev@pp3345.net>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e2ca26ec4f01486661b55b03597c13e2b9c18b73 ]

With PM enabled, I noticed that pressing a key on the droid4 keyboard will
block deeper idle states for the SoC. Let's fix this by using IRQF_ONESHOT
and stop constantly toggling the device OMAP4_KBD_IRQENABLE register as
suggested by Dmitry Torokhov <dmitry.torokhov@gmail.com>.

From the hardware point of view, looks like we need to manage the registers
for OMAP4_KBD_IRQENABLE and OMAP4_KBD_WAKEUPENABLE together to avoid
blocking deeper SoC idle states. And with toggling of OMAP4_KBD_IRQENABLE
register now gone with IRQF_ONESHOT, also the SoC idle state problem is
gone during runtime. We still also need to clear OMAP4_KBD_WAKEUPENABLE in
omap4_keypad_close() though to pair it with omap4_keypad_open() to prevent
blocking deeper SoC idle states after rmmod omap4-keypad.
Reported-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9ae4f8420ed7be4b13c96600e3568c144d101a23 ]

If "interface" is NULL then we can't release it and trying to will only
lead to an Oops.

Fixes: aea71a02 ("[SCSI] bnx2fc: Introduce interface structure for each vlan interface")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c64a87f9518409d0a439895f09f6149ffdd427b8 ]

This reverts commit db186382af21e926e90df19499475f2552192b77.

This commit introduced regression with FCP discovery so revert it to fix
discovery for FCP luns.
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 530aad77010b81526586dfc09130ec875cd084e4 ]

When adjusting sack block sequence numbers, skb_make_writable() gets
called to make sure tcp options are all in the linear area, and buffer
is not shared.

This can cause tcp header pointer to get reallocated, so we must
reaload it to avoid memory corruption.

This bug pre-dates git history.
Reported-by: NNeel Mehta <nmehta@google.com>
Reported-by: NShane Huntley <shuntley@google.com>
Reported-by: NHeather Adkins <argv@google.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>