This adds support for the MediaTek MT6397 PMIC. This is a
multifunction device with the following sub modules:

- Regulator
- RTC
- Audio codec
- GPIO
- Clock

It is interfaced to the host controller using SPI interface by a proprietary
hardware called PMIC wrapper or pwrap. MT6397 MFD is a child device of the
pwrap.

Signed-off-by: Flora Fu, MediaTek
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

There is no need to print additional ENOMEM message for
sec_platform_data allocation failure.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) were removed from rtc-s5m driver because they were not used.
Remove them (and on/off interrupt) from main MFD driver and header.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

pcr_dbg is a wrapper of dev_dbg, which can save some code,
and help to enable/disable debug message static.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add support for new chip rts525A.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

add support for new chip rts524A.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

To enable/disable ASPM we should find LINK CONTROL register
in PCI config space. All old chip use 0x80 address, but new
chip may use another address, so we using pci_find_capability()
to get LINK CONTROL address.

rtsx_gops.c was removed, we consider to put some common operations
to this file, but the actual thing is, only a group of chips
are in common ops1, and another group of chips in common ops2,
it is hard to decide put which ops into generic ops file.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Update some phy register name and value for rts5249,
the updated value makes chip more stable on some platform.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

update card drive settings, This setting can be used for rts5249
rts524A and rts525A.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

PETXCFG is defined at 0xFF03, the old 0xFE49 not used any more.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

In one shot mode, sequencer automatically disables all enabled steps at
the end of each cycle. (both ADC steps and TSC steps) Hence these steps
need not be saved in reg_se_cache for clearing these steps at a later
stage.
Also, when ADC wakes up Sequencer should not be busy executing any of the
config steps except for the charge step. Previously charge step was 1 ADC
clock cycle and hence it was ignored.
TSC steps are always disabled at the end of each conversion cycle, hence
there is no need to explicitly disable TSC steps by writing 0 to REG_SE.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Now, as all VE platforms have to be booted with DT,
the code handling non-DT case can be removed.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the DMI system ID of the Kontron COMe-cBL6 board to
the Kontron PLD driver. The list of supported products in the module
description is also updated.
Signed-off-by: NMichael Brunner <michael.brunner@kontron.com>
Acked-by: NChristian Rauch <christian.rauch@kontron.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Name changes to the battery cell structure to a
more generic cell type: fuel gauge.
Signed-off-by: NTodd Brandt <todd.e.brandt@linux.intel.com>
Acked-By: NSebastian Reichel <sre@kernel.org>
Acked-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Surely GPIO irq will be used as an input pin so make sure its direction is
set after requesting.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

It is usually better to pass actual error code from a function call than
mangling it to another.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

intel_soc_pmic_find_gpio_irq() tries to find a GPIO interrupt but doesn't
select between it or I2C interrupt so it makes more sense to move this
comment to intel_soc_pmic_i2c_probe() with minor edits.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This adds support for the Wolfson Microelectronics WM8280 and WM8281
codecs.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
[Lee: Minor fixup to remove potentially uninitialised variable. ]
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch add a missing check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
Signed-off-by: NKiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

A card insertion happens after the lastest polling before reader is
suspended may never have a chance to be detected. Under current 1-HZ
polling interval setting in mmc_core, the worst case of such
undetectablility is about 1 second.

To further reduce the undetectability, detect card slot again in suspend
method and defer the autosuspend if the slot is loaded. The default 2
second autosuspend delay of USB subsystem should let the next polling
detects the card.
Signed-off-by: NRoger Tseng <rogerable@realtek.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add device tree support for DA9063 regulators; Real-Time Clock
and Watchdog.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Driver for the Resource Power Manager (RPM) found in Qualcomm 8660, 8960
and 8064 based devices. The driver exposes resources that child drivers
can operate on; to implementing regulator, clock and bus frequency
drivers.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The driver is used only on Exynos based boards with DTS support.
After removal of board file support from max77686 and max77802 regulator
drivers, the MFD driver can be converted to DTS-only version. This
simplifies a little the code:
1. No dead (unused) entries in platform_data structure.
2. More code removed.
3. Regulator driver does not depend on allocated memory
   from MFD driver.
4. It makes also easier extending the regulator driver.

Add to the max77686 MFD driver dependency on CONFIG_OF because without
DTS the regulator drivers (max77686 and max77802) won't bind.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Removes some functions that are not used anywhere:
usbhs_readb() usbhs_writeb()

This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make array of
struct reg_default const as well.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make array of
struct reg_default const as well.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

After commit: 6e3f62f0 ("mfd: core: Fix platform-device id generation")
We must set the id base when register a duplicate name of mfd_cell.
If not, duplicate filename error was reported.

- sysfs: cannot create duplicate filename '/devices/.../wm8994-ldo'
Signed-off-by: NInha Song <ideal.song@samsung.com>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>