net/mac80211/mlme.c:2079:28: warning: symbol 'ssid_len' shadows an earlier one
net/mac80211/mlme.c:2022:12: originally declared here

ssid_len is already being declared and checked above so there is
no need for it again.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ooops...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix this build error when CONFIG_PM is not set:
drivers/net/wireless/ath/ar9170/usb.c: In function 'ar9170_usb_probe':
drivers/net/wireless/ath/ar9170/usb.c:692:
	error: 'struct usb_device' has no member named 'reset_resume'
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's not very helpful to see, in iwconfig, the current frequency
the card is tuned to if that frequency is currently somewhere
across the board because we're scanning. Since we keep track of
the frequency the user wants, display that instead.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes sparse complaint:

  CHECK   net/wireless/nl80211.c
net/wireless/nl80211.c:3694:6:
	warning: symbol 'nl80211_send_mlme_timeout'
	was not declared. Should it be static?
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

/drivers/net/wireless/p54/p54usb.c: In function 'p54u_probe':
/drivers/net/wireless/p54/p54usb.c:923: error: 'struct usb_device' has no member named 'reset_resume'

In the struct usb_device the reset_resume attribute is only available
when CONFIG_PM is defined.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes warnings:
  drivers/net/wireless/wl12xx/main.c:87: warning: int format, different
    type arg (arg 2)
  drivers/net/wireless/wl12xx/main.c: In function `wl12xx_fetch_nvs':
  drivers/net/wireless/wl12xx/main.c:125: warning: int format, different
    type arg (arg 2)
  drivers/net/wireless/wl12xx/wl1251.c: In function 'wl1251_upload_firmware':
  drivers/net/wireless/wl12xx/wl1251.c:94: warning: int format, different
    type arg (arg 2)
  drivers/net/wireless/wl12xx/wl1251.c:141: warning: int format, different
    type arg (arg 2)
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch replaces test_and_set_bit by set_bit since the bit is not
tested anyway
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch change the "is_fat" checking in rate scale to use
iwl_is_fat_tx_allowed() to match the sta and RX_ON command setting.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: NConrad Kostecki <ConiKost@gmx.de>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some issues in PS prevent us from supporting it reliably.

When 4965 goes to sleep it stores some data in host DRAM, reads it back
when device wakes up. In 4965 there is a problem that the data is not
correct when ucode starts using it upon wakeup.

For all iwlagn devices there is a problem where command is sent when PS is
enabled. At the moment there is a locking problem with priv->lock not being
held and thus not requesting nic access correctly.

We disable PS until these issues have been resolved.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch seperates rx_used and rx_free into two
different atomic contexts. We can now avoid using GFP_ATOMIC
for skb allocation and use GFP_KERNEL.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add LED support on the IBM ThinkPad 11a/b/g Wireless LAN Mini Express
Adapter (AR5BXB6), found on the IBM/Lenovo Thinkpad X60/T60/Z60 series.
Signed-off-by: NParide Legovini <legovini@spiro.fisica.unipd.it>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update ath5k to use the ctl settings for tx power based on current
regulatory domain.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Add spur filter support for RF5413 and later chips
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Add code to support the various antenna scenarios supported by hw

 * For now hardcode the default scenario (single or dual omnis with
 tx/rx diversity working and tx antenna handled by session -hw keeps
 track on which antenna it got ack from each ap/station and maps each
 ap/station to one of the antennas-).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After some debuging we were hitting the following bugs so far...

 * Due to huge channel list hostapd couldn't get infos from the driver
 and couldn't set the channel. If we manualy set the channel after
 hostapd starts (by setting channel to 0 -auto), beacons are sent
 but they wont show up on scan because they are malformed (they have
 channel = 0 because hostapd doesn't update the channel info -this is
 probably a hostapd bug so i'm CCing Jouni) and they get dropped. Bob
 fixed this by only allowing standard channels to be registered so
 now hostapd works as expected.

 * Docs (and HAL source) say that we must write 0 on timer0 when
 operating on AP mode to start TSF increment but this seems to
 mess with DBA in many cases and beacon queue never gets started.
 We fixed that on the previous patch.

 We have some more things to deal with...

 * For some reason (hw bug or something else) after restarting hostapd
 a few times, beacon inteval seems to change from 100ms to a sec
 (we get one beacon per sec).

 * We need to set sleep timers on STA mode and enable power saving +
 support PCF.

 ...but i think it's time we enable AP support "officialy" so that
 we can get more feedback from users. I ran ath5k with the mentioned
 patches + hostapd 0.6.8 and AP mode worked fine (it had some less
 throughput on my tests than IBSS but it worked).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Write next beacon timer even on AP mode since without this we get
 no beacons + ath9k does it too.  Docs say that we must write 0 on
 this register on AP mode to start TSF increment, we do both to be
 on the safe side.

 * Fix num_tx_pending function, we never read the register :P that's
 why we got all those "beacon queue 7 didn't stop messages".

 * Put full prioriy on beacon queue, lock all queues with lower
 priority using the arblock and also bypass any arblock by seting
 the arblock ignore flag.

 * For the CAB queue (do we need this thing ?, it seems crap) since
 it's supposed to fire up after each beacon (we don't use it on driver
 part, ath9k/MadWiFi does), don't make it DBA gated but instead make
 it fire after each beacon by using the beacon sent gated flag.

 * Increase bmiss threshold to 10, that's what we used on MadWiFi for
 a long time. Also when we have pending frames on the beacon queue (we
 got a beacon that didn't make it on the air) it's more likely that
 the beacon queue never started, probably due to faulty DBA setting,
 so change that "beacon queue didn't stop" message.

 Tested this with AP mode and IBSS mode and seems to work fine ;-)
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Put remaining EEPROM information on ee struct and remove is_hb63
 function.

 Now we also have rfkill stuff available.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Read Spur channel information from EEPROM and use default channels
 for RF5413 compatible chips that don't have this info on EEPROM.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Now that we have regulatory control enable the driver to set
 txpower on hw

 * Also use txpower table offset so that we can match
 power range set by user/driver with indices on power table.

 Tested 2 different cards (a CM9 and an RF5112-based ubnt) and got
 the same output using a remote machine to measure per-packet rssi
 (conected the cards using attenuators). I also switched between
 various tx power levels and i saw an equal power change on the remote
 machine (so txpower changes as expected) and verified that we have
 the same output on each rate.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ralink released a new rt2870 driver, these are the obvious
differences I could find. It doesn't same to make my device
work better, but neither does it seem to regress...
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl12xx is a driver for TI wl1251 802.11 chipset designed for embedded
devices, supporting both SDIO and SPI busses. Currently the driver
supports only SPI. Adding support 1253 (the 5 GHz version) should be
relatively easy. More information here:

http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?contentId=4711&navigationId=12494&templateId=6123

(Collapsed original sequence of pre-merge patches into single commit for
initial merge. -- JWL)
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for the rt2800usb chipset.

Current problems:
 * Cannot scan 11n AP's
 * No TX during first minute after association
 * Broken Hardware encryption

Includes various patches from Mattias, Felix, Xose and Axel.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NAxel Kollhofer <rain_maker@root-forum.org>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extra parenthesis are not needed in these 2 cases,
all other defines in rt2x00 are done without parenthesis
so just fixup these 2 cases.
Signed-off-by: NAlban Browaeys <prahal@yahoo.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The spin_lock handling uses lots of instructions on some archs.
With this patch the size of the ath9k module will be significantly
smaller.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we aren't doing anything in mac80211, we can turn off
much of the hardware, depending on the driver/hw. Not doing
anything, aka being idle, means:

 * no monitor interfaces
 * no AP/mesh/wds interfaces
 * any station interfaces are in DISABLED state
 * any IBSS interfaces aren't trying to be in a network
 * we aren't trying to scan

By creating a new function that verifies these conditions and calling
it at strategic points where the states of those conditions change,
we can easily make mac80211 tell the driver when we are idle to save
power.

Additionally, this fixes a small quirk where a recalculated powersave
state is passed to the driver even if the hardware is about to stopped
completely.

This patch intentionally doesn't touch radio_enabled because that is
currently implemented to be a soft rfkill which is inappropriate here
when we need to be able to wake up with low latency.

One thing I'm not entirely sure about is this:

  phy0: device no longer idle - in use
  wlan0: direct probe to AP 00:11:24:91:07:4d try 1
  wlan0 direct probe responded
  wlan0: authenticate with AP 00:11:24:91:07:4d
  wlan0: authenticated
> phy0: device now idle
> phy0: device no longer idle - in use
  wlan0: associate with AP 00:11:24:91:07:4d
  wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1)
  wlan0: associated

Is it appropriate to go into idle state for a short time when we have
just authenticated, but not associated yet? This happens only with the
userspace SME, because we cannot really know how long it will wait
before asking us to associate. Would going idle after a short timeout
be more appropriate? We may need to revisit this, depending on what
happens.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To deter future rate scaling algorithm writers from requesting NO_ACK
packets to be retried, throw a WARN_ON_ONCE if the algorithm hands us
a try count over 1 for NO_ACK packet.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Check for IEEE80211_TX_CTL_NO_ACK instead of is_multicast_ether_addr
when determining whether to use lowest rate without retries.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make iwl-{3945|agn}-rs check for IEEE80211_TX_CTL_NO_ACK instead of
is_multicast_ether_addr when determining whether to use the lowest
rate, and set the retry count to 0 (total try count = 1) if
IEEE80211_TX_CTL_NO_ACK is set.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make PID check for IEEE80211_TX_CTL_NO_ACK instead of
is_multicast_ether_addr when determining whether to use the lowest
rate, and set the retry count to 0 (total try count = 1) if
IEEE80211_TX_CTL_NO_ACK is set.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make the retry count zero (total try count = 1) for frames with
IEEE80211_TX_CTL_NO_ACK set.

Also remove the check for is_multicast_ether_addr in use_low_rate,
which is redundant because all multicasts have IEEE80211_TX_CTL_NO_ACK
set.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ben Greear points out that the "too many interrupts" message will
never print in the intended case since the interrupt counter
will be -1 after the loop.  Change it to pre-decrement so it will
be 0 on the thousandth iteration.

Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By placing the iv_len into the tx descriptor data and
by passing this data to the crypto IV handlers we can
save multiple calls to ieee80211_get_hdrlen_from_skb()
and some if-statements when copying/removing the IV data
from the outgoing frame.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 8e218fb2 reverted the previous
patch (commit 925be8a3).

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

remove redundant test: outlen is unsigned
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the IE buffer was allocated, the pub.information_elements pointer
was also changed to the allocated space. So we must not assume anymore
that the pointer points at the "found" tail.

So if it was allocated previously, take the codebranch that grows the
buffer size (if necessary) and put the data into the allocated buffer.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>