The omap1_defconfig this should be eventually usable for booting
all omap1 machines. Generated based on:

$ grep ARCH_OMAP1=y arch/arm/configs/* | cut -d: -f1 | xargs cat | \
     sort | uniq >> arch/arm/configs/omap1_defconfig

Then change few things manually, like use Nokia 770 CONFIG_CMDLINE
as it does not allow setting it in the bootloader.

Finally ran make savedefconfig on it.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise multi-omap1 configurations will fail.
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.

Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This way we can use the generic omap SoC detection code instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize asm_irq_flags in omap_init_irq and use it in
get_irqnr_and_base to detect between omap7xx and omap15xx/16xx.

Note that both INT_1510_IH2_IRQ and INT_1510_IH2_IRQ are defined
as 0, so use INT_1510_IH2_IRQ for both of them.
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This should be only selected in CONFIG_ARCH_OMAP2PLUS_TYPICAL
to make it easy to disable.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Using true/false instead of 1/0 to update the free variable.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Function omap_mcbsp_probe allocates struct omap_mcbsp *mcbsp but it is not
freed in omap_mcbsp_remove. Fix this, remove unneeded structure cleanups
and clk_disable calls since they are not needed here.

This is not problem currently but becomes if the mcbsp driver is ever
modularized.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Value of "isr_reg" pointer is depend on configuration and GPIO method.
Potentially it may have NULL value and it is dereferenced later
in code. Warning and exit from function are added in this case.
Signed-off-by: NEvgeny Kuznetsov <EXT-Eugeny.Kuznetsov@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In some cases we can get error function `omap2_i2c_add_bus':
arch/arm/plat-omap/i2c.c:136: undefined reference to `omap2_i2c_mux_pins'
arch/arm/plat-omap/i2c.c:141: undefined reference to `omap_hwmod_lookup'
arch/arm/plat-omap/i2c.c:157: undefined reference to `omap_device_build'
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 4d17aeb1 ("OMAP: I2C: split
device registration and convert OMAP2+ to omap_device") broke I2C on
OMAP1.  The following messages appear at boot:

i2c_omap i2c_omap.1: failure requesting irq 0
i2c_omap: probe of i2c_omap.1 failed with error -22

Investigation revealed that a chunk of code is missing from the
original plat-omap/i2c.c file which configured the IRQ and base address
for the I2C block on OMAP1.  Upon adding this back, the OMAP1 I2C block
seems to initialize correctly.

Thanks to Cory Maccarrone <darkstar6262@gmail.com> for reporting the bug,
and apologies for the breakage.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 0ea12930 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.

Fix that.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NColin Cross <ccross@android.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

gic_set_cpu will directly use irq_desc[]. If CONFIG_SPARSE_IRQ is
enabled, there is no irq_desc[]. So we need use irq_to_desc(irq) to
get the descriptor for irq.
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The existing code invokes the syscall with rubbish in r7,
due to what looks like an incorrect literal load idiom.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If CONFIG_OMAP_MUX is not enabled, we can define board_mux in the header
file instead of forcing every single board to define it.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated for combined board-zoom files]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Access to some registers depends on register access mode
Three different modes are available for OMAP (at least)
• Operational mode     LCR_REG[7] = 0x0
• Configuration mode A LCR_REG[7] = 0x1 and LCR_REG[7:0]! = 0xBF
• Configuration mode B LCR_REG[7] = 0x1 and LCR_REG[7:0]  = 0xBF

Define access modes and remove redefinitions and magic numbers
in serial drivers (and later in bluetooth driver).
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define MDR1 register serial definitions used in serial and
bluetooth drivers.
Change magic number to ones defined in serial_reg for omap1/2
serial driver.
Remove redefined MDR1 register definitions in omap-serial driver.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: NG, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Craneboard is a hardware development platform based on the
Sitara AM3517 ARM Cortex - A8 microprocessor device. This is a
low cost reference design.

This patch adds basic board file. Detailed support will follow in
subsequent patches.

  [1] http://www.ti.com/arm
  [2] http://www.mistralsolutions.com/products/craneboard.phpSigned-off-by: NSrinath <srinath@mistralsolutions.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patches removes a config option that was used to select a FIQ
handler to be build for Amstrad Delta, as required by the on-board serio
interface driver. Not having any problem reports received since it was
introduced in 2.6.35, the FIQ handler can now be built and initialized by
default, thus reqiring no extra config option.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It's easier to understand what that number means and
also avoids problems if we ever have to change it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

They are extremely similar anyway, let's get rid
of one file.

While at that, also remove the empty zoom_config
variable.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The changes are:
  - Use 'for' loop instead 'while' loop.
  - No need to initialize ret to 0, we're assigning it right after.
  - No need to check for onenandcs < GPMC_CS_NUM here, it will always be true.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap_board_config_size is implicitly initialized to 0 in
plat-omap/common.c, get_config() won't dereference omap_board_config,
so we can remove the empty igep2_config array.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

to be a few more concistant with the other boards

as ek is for evaluation kit and dk for development kit
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>

Convert the following AT91RM9200-based boards to the new-style UART
initialization:
  - Ajeco 1ARM Single Board Computer
  - Sperry-Sun KAFA board
  - picotux 200

Remove the deprecated at91_init_serial
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NAndrew Victor <linux@maxim.org.za>

Currently, the kprobes implementation for ARM only supports the ARM
instruction set, so it only works if CONFIG_THUMB2_KERNEL is not
enabled.

Until kprobes is updated to work with Thumb-2, turning it on will
cause horrible things to happen, so this patch disables it for now.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C.  If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.

In general, the following rules should be applied when using
data word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned data
words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume that
fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned, this
can cause impaired performance and stray alignment faults in some
circumstances.

In general, the following rules should be applied when using data word
declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The 32-bit conditional branches in Thumb-2 have a shorter range
(+/-512K) than their ARM counterparts (+/-32MB).  The linker does
not currently generate trampolines to extend the range of these
Thumb-2 conditional branches, resulting in link errors when vmlinux
is sufficiently large, e.g.:

head.o:(.text+0x464): relocation truncated to fit: R_ARM_THM_JUMP19

This patch forces the longer-range, unconditional branch encoding
by use of an explicit IT instruction.  The resulting branches are
triggered on the same conditions as before.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The code which makes up the zImage header intends to leave a
32-byte gap followed by a branch to the real entry point, a magic
number, and a word containing the absolute entry point address.

This gets messed up with with CONFIG_THUMB2_KERNEL, because the
size of the initial padding NOPs changes.

Instead, the header can be made fully compatible by restoring it to
ARM.

In the Thumb-2 case, we can replace the initial NOPs with a
sequence which switches to Thumb and jumps to the real entry point.

As a consequence, the zImage entry point is now always ARM, so no
special magic is needed any more for the uImage rules in the
Thumb-2 case.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some instruction operand combinations are used here which are nor
permitted in Thumb-2.

In particular, most uses of pc as an operand are disallowed in
Thumb-2, and deprecated in ARM from ARMv7 onwards.

The modified code introduced by this patch should be compatible
with all architecture versions >= v3, with or without
CONFIG_THUMB2_KERNEL.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.

In general, the following rules should be applied when using data
word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.

In this specific case, we can achieve the desired alignment by
forcing a 32-bit branch instruction using the W() macro, since the
assembler location counter is already 32-bit aligned in this case.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas.  As a result,
using these directives in code sections can result in misaligned
data words when building a Thumb-2 kernel (CONFIG_THUMB2_KERNEL).

This is a Bad Thing, since the ABI permits the compiler to assume
that fundamental types of word size or above are word- aligned when
accessing them from C.  If the data is not really word-aligned,
this can cause impaired performance and stray alignment faults in
some circumstances.

In general, the following rules should be applied when using data
word declaration directives inside code sections:

    * .quad and .double:
         .align 3

    * .long, .word, .single, .float:
         .align (or .align 2)

    * .short:
        No explicit alignment required, since Thumb-2
        instructions are always 2 or 4 bytes in size.
        immediately after an instruction.
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>