For memfree devices, the firmware QUERY_ADAPTER command does not
return vendor_id, device_id, and revision_id; do not return these
fields in the QUERY_ADAPTER function for memfree devices.

Instead, for memfree devices, initialize the rev_id field of the mthca
device via init_node_data (MAD IFC query), as is done in the
query_device verb implementation.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

    
In mthca_reg_phys_mr(), we calculate the page size for the HCA
hardware to use to map the buffer list passed in by the consumer.
For example, if the consumer passes in

    [0] addr 0x1000, size 0x1000
    [1] addr 0x2000, size 0x1000

then the algorithm would come up with a page size of 0x2000 and a list
of two pages, at 0x0000 and 0x2000.  Usually, this would work fine
since the memory region would start at an offset of 0x1000 and have a
length of 0x2000.

However, the old code did not take into account the alignment of the
IO virtual address passed in.  For example, if the consumer passed in
a virtual address of 0x6000 for the above, then the offset of 0x1000
would not be used correctly because the page mask of 0x1fff would
result in an offset of 0.

We can fix this quite neatly by making sure that the page shift we use
is no bigger than the first bit where the start of the first buffer
and the IO virtual address differ.  Also, we can further simplify the
code by removing the special case for a single buffer by noticing that
it doesn't matter if we use a page size that is too big.  This allows
the loop to compute the page shift to be replaced with __ffs().

Thanks to Bryan S Rosenburg <rosnbrg@us.ibm.com> for pointing out the
original bug and suggesting several ways to improve this patch.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch enables ehca to redirect any PMA queries to the
actual PMA QP.
Signed-off-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Reviewed-by: NJoachim Fenkes <fenkes@de.ibm.com>
Reviewed-by: NChristoph Raisch <raisch@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IB spec doesn't allow packets to QP0 sent on any other VL than VL15.
Hardware doesn't filter those packets on the send side, so we need to do
this in the driver and firmware.

As eHCA doesn't support QP0, we can just filter out all traffic going to
QP0, regardless of SL or VL.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Needed to propagate it down to the __ip_route_output_key.

Signed_off_by: Denis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes TOPDIR from infiniband Makefile and delete
one include statement pointing to a non-existing directory

Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <mshefty@ichips.intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Correctly work around T3A issues by checking "hwtype != T3A" instead of
"hwtype == T3B".  This will be needed for new hardware types.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is needed to support zero-stag properly.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The existing logic incorrectly maps this buffer list:

    0: addr 0x10001000, size 0x1000
    1: addr 0x10002000, size 0x1000

To this bogus page list:

    0: 0x10000000
    1: 0x10002000

The shift calculation must also take into account the address of the
first entry masked by the page_mask as well as the last address+size
rounded up to the next page size.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- for kernel mode cqs, call event notification handler when flushing.
- flush QP when moving from RTS -> CLOSING.
- fix logic to identify a kernel mode qp.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Move the increment of s_hdrwords into the existing if block that tests 
if we're doing a send with immediate, to save one test of the opcode.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add new mappings from port physical state (a HW register value) to the
IB SubnGet(PortInfo) port physical state.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IBA7220 uses a count-based triggering mechanism, and therefore
can't use the same bandwidth verification mechanism as older chips.

To support the 7220, allow enabling and disabling armlaunch errors on
application request.  Minor robustness improvements as well.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Clean up some unused header fields, minor related cleanup.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

IBA7220 includes many more configurable IB settings. Getting/setting
these is now grouped into a pair of chip specific functions accessed via
function pointers.  Provide sysfs access to these settings.
Signed-off-by: NMichael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This adds the new (sometimes empty) chip-specific functions to the older
chips, and makes the initialization and related functions consistent across
all 3 chips.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This code has been unused for some time, but still had leftovers
from when it was used.

Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Some HW revisions of eHCA2 may cause an RC connection to break if they
received RDMA Reads over that connection before.  This can be
prevented by assuring that, after the first RDMA Read, the QP receives
a new RDMA Read every few million link packets.

Include code into the driver that inserts an empty (size 0) RDMA Read
into the message stream every now and then if the consumer doesn't
post them frequently enough.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch enhances ehca with a capability to "autodetect" the ports
being connected physically. In order to utilize that function the
module option nr_ports must be set to -1 (default is 2 - two
ports). This feature is experimental and will made the default later.

More detail:

If the user connects only one port to the switch, current code requires
  1) port one to be connected and
  2) module option nr_ports=1 to be given.

If autodetect is enabled, ehca will not wait at creation of the GSI QP
for the respective port to become active. Since firmware does not
accept modify_qp() while the port is down at initialization, we need
to cache all calls to modify_qp() for the SMI/GSI QP and just return a
good return code.

When a port is activated and we get a PORT_ACTIVE event, we replay the
cached modify-qp() parms and re-trigger any posted recv WRs. Only then
do we forward the PORT_ACTIVE event to registered clients.

The result of this autodetect patch is that all ports will be
accessible by the users. Depending on their respective cabling only
those ports that are connected properly will become operable. If a
user tries to modify a regular QP of a non-connected port, modify_qp()
will fail. Furthermore, ibv_devinfo should show the port state
accordingly.

Note that this patch primarily improves the loading behaviour of
ehca. If the cable is removed while the driver is operating and
plugged in again, firmware will handle that properly by sending an
appropriate async event.
Signed-off-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

There are a few places in the ipath driver where a variable is
re-declared within a block where it is already in scope.  Most of these
extra declarations can simply be removed, since the variable from the
outer scope is used in a way so that it does not need to keep its
variable across the block with the re-declaration.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

t3_rdma_init_wr.irs is a big-endian field, so declare it as __be32.
This fixes one sparse warning.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Use round_jiffies() to align ehca's 1-second timer with other timers
and potentially save power by sleeping cores for longer.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NHoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The original QHT7040 had significant performance issues so there was an
additional check in the driver for a newer serial number.  Support for
the small quantities of that board shipped has been dropped, so this
patch removes the special checks to simplify the code.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Different chips have different width interrupt status registers, so add
a flag and accessor function to decide which width register read to use.
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The 6110 had a bug that caused some registers to be swapped; it was
fixed for the 7220 (and didn't affect the 6120 because it had fewer
registers).  This adds a flag and related code to handle that, and
includes some minor cleanups in the same area.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>

The number of configured ports for the 7220 changes the number of eager
TIDs available per port, for all but port 0 (kernel port) which remains
constant, so add a field to give port0 count separate from the portdata
structure.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

User registers have different alignments on different chips (4KB on
older, 64KB on 7220).  Allow mapping the user registers on kernels with
page sizes up to 64K.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Various hardware counters are exported via the ipath file system (since
it is binary data).  The old file format was very dependent on the HW
offsets for these registers.  Newer HCA chips can have different
counters at different offsets.  This patch adds a level of indirection
to make the file format consistent across HCAs.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for QLogic HCAs which have hardware performance sampling
registers for PortSamplesControl and PortSamplesResult MADs.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch moves some arrays that were defined per-device to be
variables defined in the per context data structure, thus avoiding extra
kzalloc() calls.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In preparation for upcoming chips that have different values for
INFINIPATH_R_PORTENABLE_SHIFT, INFINIPATH_R_INTRAVAIL_SHIFT,
INFINIPATH_R_TAILUPD_SHIFT, and portcfg_shift, remove the shared
#defines and use device-specific variables instead.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

kreceive is now portdata * instead of devdata * and other kreceive
related cleanups....
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove an unused parameter and fix up the comment.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch fixes a couple of minor problems with RNR NAK handling:
 - The insertion sort was causing extra delay when inserting ahead
   vs. behind an existing entry on the list.
 - A resend of a first packet of a message which is still not ready,
   needs another RNR NAK (i.e., it was suppressed when it shouldn't).
 - Also, the resend tasklet doesn't need to be woken up unless the
   ACK/NAK actually indicates progress has been made.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>