It adds the helper function of_get_phy_mode getting phy interface
from device tree.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid Miller <davem@davemloft.net>

On the recent i.mx (mx25/50/53), there is a gasket inside fec
controller which needs to be enabled no matter phy works in MII
or RMII mode.

The current code enables the gasket only when phy interface is RMII.
It's broken when the driver works with a MII phy.  The patch uses
platform_device_id to distinguish the SoCs that have the gasket and
enables it on these SoCs for both MII and RMII mode.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Reported-by: NTroy Kisky <troy.kisky@boundarydevices.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>

It adds device tree probe support for imx tty/serial driver.
Signed-off-by: NJeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: NJason Liu <jason.hui@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

The patch removes all the uses of cpu_is_mx1().  Instead, it uses
the .id_table of platform_driver to distinguish the uart device type,
IMX1_UART and IMX21_UART.  The IMX21_UART type runs on all i.mx
except i.mx1.

A couple of !cpu_is_mx1 logic gets turned into is_imx21_uart,
as the codes wrapped there are really IMX21 type uart specific.

It also removes macro MX1_UCR3_REF25 and MX1_UCR3_REF30 which are
not used anywhere.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
  OMAP: Add debugfs node to show the summary of all clocks
  OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
  OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
  OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
  OMAP2+: PM: idle clkdms only if already in idle
  OMAP2+: clockdomain: add clkdm_in_hwsup()
  OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
  OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
  OMAP4: hwmod: Introduce the module control in hwmod control
  OMAP4: cm: Add two new APIs for modulemode control
  OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
  OMAP4: hwmod data: Add PRM context register offset
  OMAP4: prm: Remove deprecated functions
  OMAP4: prm: Replace warm reset API with the offset based version
  OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
  OMAP: hwmod: Wait the idle status to be disabled
  OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
  OMAP2+: hwmod: Init clkdm field at boot time
  OMAP4: hwmod data: Add clock domain attribute
  OMAP4: clock data: Add missing divider selection for auxclks
  ...

* 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (128 commits)
  ARM: S5P64X0: External Interrupt Support
  ARM: EXYNOS4: Enable MFC on Samsung NURI
  ARM: EXYNOS4: Enable MFC on universal_c210
  ARM: S5PV210: Enable MFC on Goni
  ARM: S5P: Add support for MFC device
  ARM: EXYNOS4: Add support FIMD on SMDKC210
  ARM: EXYNOS4: Add platform device and helper functions for FIMD
  ARM: EXYNOS4: Add resource definition for FIMD
  ARM: EXYNOS4: Change devname for FIMD clkdev
  ARM: SAMSUNG: Add IRQ_I2S0 definition
  ARM: SAMSUNG: Add platform device for idma
  ARM: EXYNOS4: Add more registers to be saved and restored for PM
  ARM: EXYNOS4: Add more register addresses of CMU
  ARM: EXYNOS4: Add platform device for dwmci driver
  ARM: EXYNOS4: configure rtc-s3c on NURI
  ARM: EXYNOS4: configure MAX8903 secondary charger on NURI
  ARM: EXYNOS4: configure ADC on NURI
  ARM: EXYNOS4: configure MAX17042 fuel gauge on NURI
  ARM: EXYNOS4: configure regulators and PMIC(MAX8997) on NURI
  ARM: EXYNOS4: Increase NR_IRQS for devices with more IRQs
  ...

Fix up tons of silly conflicts:
 - arch/arm/mach-davinci/include/mach/psc.h
 - arch/arm/mach-exynos4/Kconfig
 - arch/arm/mach-exynos4/mach-smdkc210.c
 - arch/arm/mach-exynos4/pm.c
 - arch/arm/mach-imx/mm-imx1.c
 - arch/arm/mach-imx/mm-imx21.c
 - arch/arm/mach-imx/mm-imx25.c
 - arch/arm/mach-imx/mm-imx27.c
 - arch/arm/mach-imx/mm-imx31.c
 - arch/arm/mach-imx/mm-imx35.c
 - arch/arm/mach-mx5/mm.c
 - arch/arm/mach-s5pv210/mach-goni.c
 - arch/arm/mm/Kconfig

* 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: S3C64XX: Configure backup battery charger on Cragganmore
  ARM: S3C64XX: Fix WM8915 IRQ polarity on Cragganmore
  ARM: S3C64XX: Configure supplies for all Cragganmore regulators
  ARM: S3C64XX: Refresh Cragganmore support
  ARM: S3C64XX: Initial support for Wolfson/Simtec Cragganmore/Banff
  OMAP4: Keyboard: Mux changes in the board file
  omap: blaze: add mmc5/wl1283 device support
  omap: 4430SDP: Register the card detect GPIO properly
  arm: omap3: cm-t35: add support for cm-t3730
  OMAP3: beagle: add support for beagleboard xM revision C
  OMAP3: rx-51: Add full regulator definitions
  omap: rx51: Platform support for lp5523 led chip

Merge branch 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc

* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: Consolidate the clkdev header files
  ARM: set vga memory base at run-time
  ARM: convert PCI defines to variables
  ARM: pci: make pcibios_assign_all_busses use pci_has_flag
  ARM: remove unnecessary mach/hardware.h includes
  pci: move microblaze and powerpc pci flag functions into asm-generic
  powerpc: rename ppc_pci_*_flags to pci_*_flags

Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h

* 'next/fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (24 commits)
  ASoC: omap: McBSP: fix build breakage on OMAP1
  OMAP: hwmod: fix the i2c-reset timeout during bootup
  I2C: OMAP2+: add correct functionality flags to all omap2plus i2c dev_attr
  I2C: OMAP2+: Tag all OMAP2+ hwmod defintions with I2C IP revision
  I2C: OMAP1/OMAP2+: create omap I2C functionality flags for each cpu_... test
  I2C: OMAP2+:  Introduce I2C IP versioning constants
  I2C: OMAP2+: increase omap_i2c_dev_attr flags from u8 to u32
  I2C: OMAP2+: Set hwmod flags to only allow 16-bit accesses to i2c
  OMAP4: hwmod data: Change DSS main_clk scheme
  OMAP4: powerdomain data: Remove unsupported MPU powerdomain state
  OMAP4: clock data: Keep GPMC clocks always enabled and hardware managed
  OMAP4: powerdomain data: Fix core mem states and missing cefuse flag
  OMAP2+: PM: Initialise sleep_switch to a non-valid value
  OMAP4: hwmod data: Modify DSS opt clocks
  OMAP4: iommu: fix clock name
  omap: iovmm: s/sg_dma_len(sg)/sg->length/
  omap: iommu: fix pte programming
  arm: omap3: cm-t35: fix slow path warning
  arm: omap3: cm-t35: minor comments fixes
  omap: ZOOM: QUART: Request reset GPIO
  ...

* 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  MAINTAINERS: add maintainer of CSR SiRFprimaII machine
  ARM: CSR: initializing L2 cache
  ARM: CSR: mapping early DEBUG_LL uart
  ARM: CSR: Adding CSR SiRFprimaII board support
  OMAP4: clocks: Update the clock tree with 4460 clock nodes
  OMAP4: PRCM: OMAP4460 specific PRM and CM register bitshifts
  OMAP4: ID: add omap_has_feature for max freq supported
  OMAP: ID: introduce chip detection for OMAP4460
  ARM: Xilinx: merge board file into main platform code
  ARM: Xilinx: Adding Xilinx board support

Fix up conflicts in arch/arm/mach-omap2/cm-regbits-44xx.h

* 'next-i2c' of git://git.fluff.org/bjdooks/linux:
  i2c-eg20t : Fix the issue of Combined R/W transfer mode
  i2c-eg20t : Support Combined R/W transfer mode
  i2c: Tegra: Add DeviceTree support

Only a few core funcs need to be implemented for SMP systems, so allow the
arches to override them while getting the rest for free.

At least, this is enough to allow the Blackfin SMP port to use things.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Arun Sharma <asharma@fb.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since arches are expected to implement this guy, add a common version for
people the same way as atomic_clear_mask is handled.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Arun Sharma <asharma@fb.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The atomic helpers are supposed to take an atomic_t pointer, not a random
unsigned long pointer.  So convert atomic_clear_mask over.

While we're here, also add some nice documentation to the func.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Arun Sharma <asharma@fb.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We already declared inc/dec helpers, so we don't need to call the
atomic_{add,sub}_return funcs directly.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Arun Sharma <asharma@fb.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This clarifies the differences between <linux/atomic.h> and
<asm-generic/atomic.h>
Signed-off-by: NArun Sharma <asharma@fb.com>
Suggested-by: NMike Frysinger <vapier.adi@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:

linux/atomic.h
  -> asm/atomic.h
    -> asm-generic/atomic-long.h

where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype.  This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.

Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).

Compile tested on i386 and x86_64 with allnoconfig.
Signed-off-by: NArun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is in preparation for more generic atomic primitives based on
__atomic_add_unless.
Signed-off-by: NArun Sharma <asharma@fb.com>
Signed-off-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: NArun Sharma <asharma@fb.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The majority of architectures implement ext2 atomic bitops as
test_and_{set,clear}_bit() without spinlock.

This adds this type of generic implementation in ext2-atomic-setbit.h and
use it wherever possible.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Suggested-by: NAndreas Dilger <adilger@dilger.ca>
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This changes should_fail_request() to more usable wrapper function of
should_fail().  It can avoid putting #ifdef CONFIG_FAIL_MAKE_REQUEST in
the middle of a function.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now cleanup_fault_attr_dentries() recursively removes a directory, So we
can simplify the error handling in the initialization code and no need
to hold dentry structs for each debugfs file.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now cleanup_fault_attr_dentries() recursively removes a directory, So we
can simplify the error handling in the initialization code and no need
to hold dentry structs for each debugfs file.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use debugfs_remove_recursive() to simplify initialization and
deinitialization of fault injection debugfs files.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Minor cosmetic changes for simple attribute of stacktrace_depth:

 - use min_t()
 - reduce #ifdef by moving a function
 - do not use partly capitalized function name
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

should_fail_srandom() does not exist.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No need to include linux/kallsyms.h.
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The size of the dump is currently set using the RECORD_SIZE macro which
is set to a page size.  This patch makes the record size a module
parameter and allows it to be set through platform data as well to allow
larger dumps if needed.
Signed-off-by: NSergiu Iordache <sergiu@chromium.org>
Acked-by: NMarco Stornelli <marco.stornelli@gmail.com>
Cc: "Ahmed S. Darwish" <darwish.07@gmail.com>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The platform driver currently allows setting the mem_size and
mem_address.

ince dump_oops is also a module parameter it would be more consistent if
it could be set through platform data as well.
Signed-off-by: NSergiu Iordache <sergiu@chromium.org>
Acked-by: NMarco Stornelli <marco.stornelli@gmail.com>
Cc: "Ahmed S. Darwish" <darwish.07@gmail.com>
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add new line to each print.
Signed-off-by: NMarco Stornelli <marco.stornelli@gmail.com>
Reported-by: NStevie Trujillo <stevie.trujillo@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use generic module parameters instead of platform data, if platform data
are not available.  This limitation has been introduced with commit
c3b92ce9 ("ramoops: use the platform data structure instead of module
params").

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NMarco Stornelli <marco.stornelli@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Reported-by: NStevie Trujillo <stevie.trujillo@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With the arrival of concurrency-managed workqueues there is no need for
our driver to use dedicated workqueue; system-wide one should suffice just
fine.

[akpm@linux-foundation.org: fix comment layout & grammar]
Signed-off-by: NDmitry Torokhov <dtor@vmware.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NChristian Glindkamp <christian.glindkamp@taskit.de>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Don't force output if you intend to reboot immediately.

In this patch, I'm disabling the functionality enabled by
vc->vc_panic_force_write if panic_timeout < 0 (i.e.  no timeout).
vc_panic_force_write is only enabled for fb video consoles if the
FBINFO_CAN_FORCE_OUTPUT flag is set.

For our application, we're using ram_oops to preserved the panic in
memory.  We want to reliably, and as fast as possible, machine_restart.
The vc_panic_force_write flag results in a bunch of graphics driver code
to be invoked which slows down restart and decreases reliability.  Since
we're already storing the panic in RAM and are going to reboot
immediately, there is no benefit in mode switching back to the vc in
order to display the panic output.  The log buffer will get flushed by
the console_unblank() call so remote management consoles should see all
output.
Signed-off-by: NMandeep Singh Baines <msb@chromium.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Olaf Hering <olaf@aepfle.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When a kernel BUG or oops occurs, ChromeOS intends to panic and
immediately reboot, with stacktrace and other messages preserved in RAM
across reboot.

But the longer we delay, the more likely the user is to poweroff and
lose the info.

panic_timeout (seconds before rebooting) is set by panic= boot option or
sysctl or /proc/sys/kernel/panic; but 0 means wait forever, so at
present we have to delay at least 1 second.

Let a negative number mean reboot immediately (with the small cosmetic
benefit of suppressing that newline-less "Rebooting in %d seconds.."
message).
Signed-off-by: NHugh Dickins <hughd@chromium.org>
Signed-off-by: NMandeep Singh Baines <msb@chromium.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Olaf Hering <olaf@aepfle.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

See: DMA-API.txt, part Id, DMA_FROM_DEVICE description.
Signed-off-by: NMichal Miroslaw <mirq-linux@rere.qmqm.pl>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

git grep shows there are no users in tree, so we can remove them safely.
Signed-off-by: NWANG Cong <xiyou.wangcong@gmail.com>
Acked-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NVinod Koul <vinod.koul@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Selecting GCOV for UML causing configuration mismatch:

  warning: (GCOV_KERNEL) selects CONSTRUCTORS which has unmet direct dependencies (!UML)

Constructors are not needed for UML.
Signed-off-by: NVitaliy Ivanov <vitalivanov@gmail.com>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Acked-by: NRichard Weinberger <richard@nod.at>
Acked-by: NWANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Parameter offset_in_page in edac_mc_handle_ce() should mask the higher
bits above the page size, not the lower bits.  The original input
sometimes causes a crash.
Signed-off-by: NKai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the shm_rmid_forced sysctl.  If set to 1, all shared
memory objects in current ipc namespace will be automatically forced to
use IPC_RMID.

The POSIX way of handling shmem allows one to create shm objects and
call shmdt(), leaving shm object associated with no process, thus
consuming memory not counted via rlimits.

With shm_rmid_forced=1 the shared memory object is counted at least for
one process, so OOM killer may effectively kill the fat process holding
the shared memory.

It obviously breaks POSIX - some programs relying on the feature would
stop working.  So set shm_rmid_forced=1 only if you're sure nobody uses
"orphaned" memory.  Use shm_rmid_forced=0 by default for compatability
reasons.

The feature was previously impemented in -ow as a configure option.

[akpm@linux-foundation.org: fix documentation, per Randy]
[akpm@linux-foundation.org: fix warning]
[akpm@linux-foundation.org: readability/conventionality tweaks]
[akpm@linux-foundation.org: fix shm_rmid_forced/shm_forced_rmid confusion, use standard comment layout]
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Serge E. Hallyn" <serge.hallyn@canonical.com>
Cc: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Solar Designer <solar@openwall.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>