Change from using the __raw IO accesors to the endian agnostic versions
of readl/writel_relaxed when not on AVR32. This fixes issues with running
big endian on ARMv7.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
--
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: linux-usb@vger.kernel.org
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If USB PLL is not necessary for other USB drivers (e.g. OHCI and EHCI)
we will reduce power consumption by switching off the USB PLL if no USB
Host is currently connected to this USB Device.

We are using Vbus GPIO signal to detect Host presence. If Vbus signal is
not available then the device stays continuously clocked.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Cache INT_ENB register value in order to avoid uncached iomem access, and
thus improve access time to INT_ENB value.
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

at91sam9g45 and at91sam9x5 SoCs have an hardware bug forcing us to
generate a pulse on the BIAS signal on "USB end of reset” and
“USB end of resume" events.
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Reported-by: NPatrice VILCHEZ <patrice.vilchez@atmel.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

at91sam9rl SoC has an erratum forcing us to toggle the BIAS on USB
suspend/resume events.

This specific handling is only activated when CONFIG_ARCH_AT91SAM9RL is
set and this option is only set when building a non-DT kernel, which is
problematic since non-DT support for at91sam9rl SoC has been removed.

Rework the toggle_bias implementation to attach it to the "at91sam9rl-udc"
compatible string.

Add new compatible strings to avoid executing at91sam9rl erratum handling
on other SoCs.
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The drivers/usb/gadget directory contains many files.
Files which are related can be distributed into separate directories.
This patch moves the UDC drivers into a separate directory.
Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The SoCs earlier than sama5d3, they have the same number endpoints
and DMA channels. In driver code, they use the same definition
USBA_NR_ENDPOINTS for both endpoints and dma channels. However,
in sama5d3, it has different number for endpoints and DMA channels.
So, define a new macro USBA_NR_DMAs for DMA channels. And the
USBA_NR_ENDPOINS is not used anymore, remove it at the same time.
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Allow to compile the driver all the time if AT91 enabled.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NBo Shen <voice.shen@atmel.com>

so we can have multiple usb gadget instance
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NBo Shen <voice.shen@atmel.com>

DMA_ADDR_INVALID isn't (and shouldn't) be used
anymore, let's remove it.
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove redundant pointer to struct usb_endpoint_descriptor.
Signed-off-by: NIdo Shayevitz <idos@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Adding vbus_pin_inverted so that the usb detect pin can be active high
or low depending on HW implementation also replaced the
gpio_get_value(udc->vbus_pin); with a call to vbus_is_present(udc); This
allows the driver to be loaded and save about 0,15W on the consumption.
Signed-off-by: NEirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is part of the series adding support for the USB High
Speed Device Port on the AT91CAP9 system on chip. The AT91CAP9
uses the same UDPHS IP as the AVR32 and the AT91SAM9RL.

The only differences between the AVR32 and the AT91 version of the
device are in the enable/disable and suspend/wakeup sequences: the
AT91 version needs to toggle the USB bias and pulldown explicitly.
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

We now have pr_err(), pr_warning(), and friends ... start using
them in the gadget stack instead of printk(KERN_ERR) and friends.
This gives us shorter lines and somewhat increased readability.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Keep track of the device status (as returned by the GET_STATUS
request) and allow it to be manipulated by set_selfpowered() as
well as SET_FEATURE/CLEAR_FEATURE (for remote wakeup)

Implement the wakeup() op, which refuses to do anything if the
DEVICE_REMOTE_WAKEUP feature wasn't set by the host.  Now this
driver passes USBCV (at least, with gadget zero).

Fix one more locking bug; lockdep is every developer's friend.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is a driver for the Atmel USBA UDC which can be found integrated
on AT32AP700x AVR32 processors. For hardware documentation, please see
the AT32AP7000 data sheet:

http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf

This is a dual speed controller (connects at high or full speed).
The driver supports up to 7 control, bulk, interrupt and isochronous
endpoints with some constraints. Bulk, interrupt and isochronous
transfers are driven by DMA.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>