Streamlining sdio bus specific header related code as preparation for host
tx glomming
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

remove align from brcmf_bus since it is only used by sdio bus layer internally
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Abstract brcmf_sdio_txpkt_prep and brcmf_sdio_txpkt_postp as a preparation
of chained tx packets for host side tx glomming.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement the .tdls_oper() callback and indicate TDLS support
in the wiphy flags.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not every IF event from the firmware needs to result in a
related interface, netdev or wdev, on the host. This is
indicated in the event message. Handle that flag and effectively
ignore the firmware event.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

FWS uses locking to protect its data while being called from
various entries. On bus_txdata the lock was kept resulting in
unnecessary long locking, but also creating possibility for
deadlock. This update changes the locking to release lock when
bus_txdata is called.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When fw signalling is disabled tx is sent immediately. Using
queues and worker thread allows usb to do synchronous autopm. This
patch makes fws use queues and worker thread even if signalling is
not supported by FW or not enabled.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This feature moves the responsibility of collecting all MPDUs in an
AMPDU session in the correct order from the firmware to the host
driver. This reduces buffer requirement on the firmware side.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With firmware-signalling the packet handed to the bus specific driver
layer should not be discarded with brcmf_txcomplete() in the failure
path. Instead only an error is returned and the caller decides what
to do with the packet.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware-signalling needs transmit to firmware to be atomic and
uses a spinlock with irq disabled. Therefor, brcmf_sdbrcm_txdata()
should not use spin_unlock_bh() as it would enable the interrupts.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Samuel Ortiz <sameo@linux.intel.com> says:

"This is the first NFC pull request for the 3.12 release.

With this one we have:

- A few pn533 improvements and minor fixes. Testing our pn533 driver
  against Google's NCI stack triggered a few issues that we fixed now.
  We also added Tx fragmentation support to this driver.

- More NFC secure element handling. We added a GET_SE netlink command
  for getting all the discovered secure elements, and we defined 2
  additional secure element netlink event (transaction and connectivity).
  We also fixed a couple of typos and copy-paste bugs from the secure
  element handling code.

- Firmware download support for the pn544 driver. This chipset can enter a
  special mode where it's waiting for firmware blobs to replace the
  already flashed one. We now support that mode."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The secure element state was not updated from the enable/disable ops,
leaving the SE state to disabled for ever.
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Another typo from the initial commit where we check for the secure
element type field instead of its state when enabling or disabling it.
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

There is a cut and paste bug so we enable a second time instead of
disabling.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The pn544 can enter a firmware update mode where firmware blobs can be
pushed through the i2c line and flashed on the target.
A special command allows to verify that blobs are correctly flashed and
this is what we do for every downloaded firmware blob.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The firmware operation callback is passed by the physical layer to the
hci driver during probe. All the driver does is to store it and call it
when the fw_upload hci ops is invoked.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Result is added as an NFC_ATTR_FIRMWARE_DOWNLOAD_STATUS attribute
containing the standard errno positive value of the completion result.
This event will be sent when the firmare download operation is done and
will contain the operation result.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is in preparation for pn544-i2c firmware download feature, where we
need to know if we're in regular or firmware upload mode.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This API must be called by NFC drivers, and its prototype was
incorrectly placed.
Signed-off-by: NEric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

By not always starting the polling loop from the same modulation, we
avoid entering infinite loops where devices exporting 2 targets (on 2
different modulations) get the same target activated over and over.
If this target is not readable (e.g. a wallet emulating a tag), we will
stay in an error loop for ever.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

It seems that some pn533 firmwares go belly up when being asked to send
poll frames too frequently. Adding a 10ms delay between each of them
calm the chip down and prevent it from crashing.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

In order to fetch the discovered secure elements from an NFC controller,
we need to send a netlink command that will dump the list of available
SEs from NFC.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is a typo coming from the initial implementation. se_discover fails
when it returns something different than zero and we should only display
a warning in that case.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The extended information frame are sent by PN533 to exchange frames
larger than 255 bytes. These extended frame are very close from the
standard ones except for the header size length. On each incoming
frame, we set the correct header length, and we do that only for the
standard pn533 chipsets as the acr122 does not seem to support extended
frames properly.
Signed-off-by: NOlivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

On sending large frames (size > 262), we split it in multiple chunks and
send them asynchronously with MI bit.
Signed-off-by: NOlivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Extended Information frames are slightly different from standard frames
as they can (theorically) handle datas up tu 64kB. PN533 firmware only
supports packet data up to 265 (incl. TFI byte)
This kind of frame are used when the pn533 wants to exchange more than
255 bytes, and this patch handles the reception of such frames.
Signed-off-by: NOlivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The AUTO RFCA bit forbids the pn533 chipset to turn its radio on
whenever an external field is present.
Without this bit set, some devices seems to get over flood by the
pn533 rf field and thus become hardly detectable.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

p2p devices must be able to support 424 kbps, so we should always select
that bitrate in initiator mode.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Some devices are getting confused when not being asked for their system
code with type F.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

By turning the radio off after each failed polling try, we dramatically
improve the pn533 polling loop efficiency.
Without this fix, all Android phones running the broadcom NFC stack are
almost never detected.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

By using the standard setting for the regular pn533 dongles, we no
longer wait for ever for an ATR_RES. Without this, a failing ATR_REQ
will put the hardware into a busy loop, constantly waiting for an
ATR_RES.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The SE_CONNECTIVITY event is for an SE to request connection to e.g. a
modem. The SE_TRANSACTION one is sent when an application running on a
specific SE wants to notify the host CPU about the end of a transaction.
Those events respectively map to the EVT_CONNECTIVITY and the
EVT_TRANSACTION HCI events.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch fixes 3 sparse warnings:
nfcsim.c:63:25: sparse: symbol 'wq' was not declared.
nfcsim.c:484:12: sparse: symbol 'nfcsim_init' was not declared.
nfcsim.c:525:13: sparse: symbol 'nfcsim_exit' was not declared.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NThierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

config: make ARCH=m68k allmodconfig

All error/warnings:

   drivers/net/wireless/mwifiex/cfg80211.c: In function
       'mwifiex_fill_coalesce_rule_info':
>> drivers/net/wireless/mwifiex/cfg80211.c:2493:3: error: implicit
       declaration of function 'mwifiex_is_pattern_supported'
       [-Werror=implicit-function-declaration]
   drivers/net/wireless/mwifiex/cfg80211.c: At top level:
   drivers/net/wireless/mwifiex/cfg80211.c:2537:12: warning:
       'mwifiex_cfg80211_set_coalesce' defined but not used
       [-Wunused-function]
   cc1: some warnings being treated as errors
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LNA combining algorithm has to be run for cards
that support the required diversity features, make
sure that that correct conditions are met before
enabing this algorithm.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BTCOEX has to be *disabled* for WLAN RX diversity to
work on combo cards.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Create a per-vif dummy node entry for keeping the multicast software
queues. This helps in setups with a lot of mulitcast traffic that could
otherwise potentially drown out unicast traffic to stations.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>