- 05 12月, 2015 1 次提交
-
-
由 Al Cooper 提交于
Currently usb_port_resume waits for up to 2 seconds for CONNECT status for SS devices only. This change will do the same thing for non-SS devices even though the reason is a little different. This will fix an issue where VBUS is turned off during system wide "suspend to ram" and some 2.0 devices take greater than the current max of 100ms to show connected after VBUS is enabled. This is most commonly seen on hard drive based devices and USB3.0 devices plugged into a 2.0 only port. Signed-off-by: NAl Cooper <alcooperx@gmail.com> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 02 12月, 2015 34 次提交
-
-
由 Lu Baolu 提交于
Commit 8306095f ("USB: Disable USB 3.0 LPM in critical sections.") adds usb3_lpm_enabled member to struct usb_device. There is no reference to this member now. Hence, it could be removed. Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Lu Baolu 提交于
USB3 LPM is default on in Linux kernel if both xHCI host controller and the USB devices declare to be LPM-capable. Unfortunately, some devices are known to work well with LPM disabled, but to be broken if LPM is enabled, although it declares the LPM capability. Users won't be able to use this kind of devices, until someone puts them in the kernel blacklist and gets the kernel upgraded. This patch adds a sysfs node to permit or forbit USB3 LPM U1 or U2 entry for a port. The settings apply to both before and after device enumeration. Supported values are "0" - neither u1 nor u2 permitted, "u1" - only u1 is permitted, "u2" - only u2 is permitted, "u1_u2" - both u1 and u2 are permitted. With this interface, users can use an LPM-unfriendly USB device on a released Linux kernel. Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com> Signed-off-by: NZhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Lu Baolu 提交于
Commit 655fe4ef ("usbcore: add sysfs support to xHCI usb3 hardware LPM") introduced usb3_hardware_lpm sysfs node. This doesn't show the correct status of USB3 U1 and U2 LPM status. This patch fixes this by replacing usb3_hardware_lpm with two nodes, usb3_hardware_lpm_u1 (for U1) and usb3_hardware_lpm_u2 (for U2), and recording the U1/U2 LPM status in right places. This patch should be back-ported to kernels as old as 4.3, that contains Commit 655fe4ef ("usbcore: add sysfs support to xHCI usb3 hardware LPM"). Cc: stable@vger.kernel.org Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Andy Gross 提交于
This patch sets the AHBMODE to allow for posted data writes. This results in higher performance. Signed-off-by: NAndy Gross <agross@codeaurora.org> Tested-by: NGeorgi Djakov <georgi.djakov@linaro.org> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Andy Gross 提交于
This patch sets the AHBMODE to allow for posted data writes. This results in higher performance. Signed-off-by: NAndy Gross <agross@codeaurora.org> Acked-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Tina Ruchandani 提交于
struct mon_bin_hdr allows for a 64-bit seconds timestamp. The code currently uses 'struct timeval' to populate the timestamp in mon_bin_hdr, which has a 32-bit seconds field and will overflow in year 2038 and beyond. This patch replaces 'struct timeval' with 'struct timespec64' which is y2038 safe. This patch is part of a larger attempt to remove instances of struct timeval and other 32-bit timekeeping (time_t, struct timespec) from the kernel. Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com> Reviewed-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Deepa Dinamani 提交于
timeval is deprecated and not y2038 safe. Its size also changes according to 32 bit/ 64 bit compilation. Replace it with 32 and 64 bit versions of its individual fields, giving two ioctls with different code values. The two ioctls are necessary to maintain the 32 bit and 64 bit userspace compatibility with a 64/32 bit kernel. Change unsigned to __u32 types for a definitive userspace interface. This is in accordance with the psABI that the unsigned type is always 32 bits. Also use motonic timer instead of real time to ensure positive delta values. Refactor usbtest_ioctl for readability to isolate the handling of the testing timing measurement. The official testusb userspace tool can be changed in a separate patch to reflect the __u32 changes as well. It can use the usbtest_param_32 struct, since 32 bit seconds is long enough for test durations. Signed-off-by: NDeepa Dinamani <deepa.kernel@gmail.com> Reviewed-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Tina Ruchandani 提交于
struct timeval' uses 32-bits for its seconds field and will overflow in the year 2038 and beyond. This patch replaces the usage of 'struct timeval' in mon_get_timestamp() with timespec64 which uses a 64-bit seconds field and is y2038-safe. mon_get_timestamp() truncates the timestamp at 4096 seconds, so the correctness of the code is not affected. This patch is part of a larger attempt to remove instances of struct timeval and other 32-bit timekeeping (time_t, struct timespec) from the kernel. Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com> Suggested-by: NArnd Bergmann <arnd@arndb.de> Reviewed-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Rafał Miłecki 提交于
So far we were using simple (legacy) GPIO functions & some poor logic to control power. It got many drawbacks: we were ignoring OF flags (GPIO_ACTIVE_LOW), we were not setting direction to output and we were assuming gpio_request success all the time. Fix it by switching to gpiod functions and adding appropriate checks. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Acked-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Julia Lawall 提交于
The usb_mon_operations structure is never modified, so declare it as const. Done with the help of Coccinelle. Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Peter Chen 提交于
Now the function of complicated_callback is not only used for iso transfer, improve the error message to reflect it. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Saurabh Sengar 提交于
for checking if a property is present or not, of_property_read_bool is more appropriate than of_get_property() Signed-off-by: NSaurabh Sengar <saurabh.truth@gmail.com> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Oliver Neukum 提交于
This function must be called with a spinlock held. Memory can be allocated only with GFP_ATOMIC. Passing a gfp_t argument is a waste. Signed-off-by: NOliver Neukum <oneukum@suse.com> Reviewed-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Oliver Neukum 提交于
Use this macro to make the driver more readable. Signed-off-by: NOliver Neukum <oneukum@suse.com> Reviewed-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Markus Elfring 提交于
The dma_pool_destroy() function tests whether its argument is NULL and then returns immediately. Thus the test around the calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Saurabh Sengar 提交于
replace dma_pool_alloc and memset with a single call to dma_pool_zalloc Signed-off-by: NSaurabh Sengar <saurabh.truth@gmail.com> Acked-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Jiri Kosina 提交于
uwbd() calls try_to_freeze(), but the thread doesn't mark itself freezable through set_freezable(), so the try_to_freeze() call is useless. Signed-off-by: NJiri Kosina <jkosina@suse.cz> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Mathias Nyman 提交于
Replace the existing two extended capability parsing helper functions with one called xhci_find_next_ext_cap(). The extended capabilities are read both in pci-quirks before xhci driver is loaded, and inside the xhci driver when adding ports. The existing helpers did not suit well for these cases and a lot of custom parsing code was needed. The new helper function simplifies these two cases a lot. The motivation for this rework was that code to support xhci debug capability needed to parse extended capabilities, and it included yet another capability parsing helper specific for its needs. With this solution it debug capability code can use this new helper as well Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Mathias Nyman 提交于
Don't use dev_warn() for intened behaviour, use dev_dbg() Rounding down the interval to the nearest power of 2 is required by xhci specs. Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Chunfeng Yun 提交于
add xHCI and phy drivers for MT8173-EVB Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Chunfeng Yun 提交于
There some vendor quirks for MTK xhci host controller: 1. It defines some extra SW scheduling parameters for HW to minimize the scheduling effort for synchronous and interrupt endpoints. The parameters are put into reseved DWs of slot context and endpoint context. 2. Its IMODI unit for Interrupter Moderation register is 8 times as much as that defined in xHCI spec. 3. Its TDS in Normal TRB defines a number of packets that remains to be transferred for a TD after processing all Max packets in all previous TRBs. Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com> Tested-by: NDaniel Thompson <daniel.thompson@linaro.org> Reviewed-by: NDaniel Thompson <daniel.thompson@linaro.org> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Chunfeng Yun 提交于
add a DT binding documentation of xHCI host controller for the MT8173 SoC from Mediatek. Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Yoshihiro Shimoda 提交于
The R-Car H3 has two xHCI controllers. This SoC is compatible with R-Car Gen2 SoCs, however this SoC doesn't need some specific registers setting, and need a new firmware. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Yoshihiro Shimoda 提交于
This patch adds support for R-Car M2-N (r8a7793) xHCI controller. This SoC is compatible with R-Car H2 (r8a7790) and R-Car M2-W (r8a7791). Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Yoshihiro Shimoda 提交于
This patch changes code to ease the addition of next generation SoCs. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Yoshihiro Shimoda 提交于
This patch adds a member "firmware_name" in struct xhci_plat_priv to simplify the code to match specific firmware name. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Yoshihiro Shimoda 提交于
This patch adds struct xhci_plat_priv to simplify the code to match platform specific variables. For now, this patch adds a member "type" in the structure. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Yoshihiro Shimoda 提交于
This patch adds an xhci->priv field for private use by XHCI platform drivers. Until now none of the platform drivers has used this private space. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Yoshihiro Shimoda 提交于
This patch cleanups the hcd private size to suitable size. The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides or xhci_pci_overrides as extra_priv_size. However, the xhci driver uses a "sizeof(struct xhcd_hcd)" memory space in each hcd (main_hcd and shared_hcd) actually. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Mathias Nyman 提交于
use the variables defined for populating the port status and port chage bits retuend by GetPortStatus request intead of the hub class feature selectors. The defines for hub class feature selectors are used for other purposes, they work as port status and feature selectors are in the same order, and set the same bits, but it makes the code very hard to follow Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Alan Stern 提交于
This patch adds a new warning message to ehci-hcd. The warning is triggered whenever the driver finds that the hardware has set the Active bit in a QH at a time when the driver expects the QH to be completely idle. Such bugs have been observed by users in the past, and since they can lead to serious problems (such as inability to unlink an URB that never completes), it would be good to know about them when they occur. This won't fix these bugs; that's a bigger job for a later patch. But success isn't guaranteed, since this depends on aspects of the hardware which are not documented in the EHCI spec or for which the spec's recommendations are clearly unworkable. It therefore seems worthwhile to check for these bugs proactively. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Reported-by: NMichael Reutman <mreutman@epiqsolutions.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Alan Stern 提交于
This patch enhances the "async" debugfs file in ehci-hcd by printing out several additional fields in the hardware-accessible data structures. These fields are important for determining the hardware's view of the async schedule, in particular, the addresses of the current and next qTDs for each QH along with the start address of each qTD's data buffer. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Alan Stern 提交于
This patch improves the usbfs_snoop debugging facility by adding messages for a couple of significant events which, up to now, have not been logged. The events are reaping and discarding (i.e., cancelling) an URB. The debugging messages include the userspace address of the URB being reaped or discarded. The reaping messages have to be added in four places, in order to handle blocking and non-blocking reaps in both normal and 32-bit compatibility mode. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Alan Stern 提交于
The usbfs_snoop facility can be very useful for debugging problems involving usbfs. However, it always prints out the entire contents of every URB. When dealing with large quantities of data, this can be less than helpful. This patch ameliorates the situation by adding a module parameter to usbcore for controlling the maximum number of bytes to print when snooping an URB. This makes debugging much easier. For backward compatibility, the default value is set unreasonably high. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 30 11月, 2015 5 次提交
-
-
由 Linus Torvalds 提交于
-
git://people.freedesktop.org/~airlied/linux由 Linus Torvalds 提交于
Pull nouveau and radeon fixes from Dave Airlie: "Just some nouveau and radeon/amdgpu fixes. The nouveau fixes look large as the firmware context files are regenerated, but the actual change is quite small" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/radeon: make some dpm errors debug only drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set drm/nouveau/nvif: allow userspace access to its own client object drm/nouveau/gr/gf100-: fix oops when calling zbc methods drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC drm/nouveau/gr/gf100-: split out per-gpc address calculation macro drm/nouveau/bios: return actual size of the buffer retrieved via _ROM drm/nouveau/instmem: protect instobj list with a spinlock drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop drm/nouveau/pci: enable c800 magic for Clevo P157SM drm/radeon: make rv770_set_sw_state failures non-fatal drm/amdgpu: move dependency handling out of atomic section v2 drm/amdgpu: optimize scheduler fence handling drm/amdgpu: remove vm->mutex drm/amdgpu: add mutex for ba_va->valids/invalids drm/amdgpu: adapt vce session create interface changes drm/amdgpu: vce use multiple cache surface starting from stoney drm/amdgpu: reset vce trap interrupt flag
-
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux由 Linus Torvalds 提交于
Pull RTC fixes from Alexandre Belloni: "Two fixes for the ds1307 alarm and wakeup" * tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: rtc: ds1307: fix alarm reading at probe time rtc: ds1307: fix kernel splat due to wakeup irq handling
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linus由 Linus Torvalds 提交于
Pull MIPS fix from Ralf Baechle: "Just a fix for empty loops that may be removed by non-antique GCC" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: MIPS: Fix delay loops which may be removed by GCC.
-
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k由 Linus Torvalds 提交于
Pull m68k fixes from Geert Uytterhoeven: "Summary: - Add missing initialization of max_pfn, which is needed to make selftests/vm/mlock2-tests succeed, - Wire up new mlock2 syscall" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: m68k: Wire up mlock2 m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn m68k/mm: m54xx - Add missing initialization of max_pfn m68k/mm: motorola - Add missing initialization of max_pfn
-