The current LPM implementation has the following issues.

* Operation order isn't well thought-out.  e.g. HIPM should be
  configured after IPM in SControl is properly configured.  Not the
  other way around.

* Suspend/resume paths call ata_lpm_enable/disable() which must only
  be called from EH context directly.  Also, ata_lpm_enable/disable()
  were called whether LPM was in use or not.

* Implementation is per-port when it should be per-link.  As a result,
  it can't be used for controllers with slave links or PMP.

* LPM state isn't managed consistently.  After a link reset for
  whatever reason including suspend/resume the actual LPM state would
  be reset leaving ap->lpm_policy inconsistent.

* Generic/driver-specific logic boundary isn't clear.  Currently,
  libahci has to mangle stuff which libata EH proper should be
  handling.  This makes the implementation unnecessarily complex and
  fragile.

* Tied to ALPM.  Doesn't consider DIPM only cases and doesn't check
  whether the device allows HIPM.

* Error handling isn't implemented.

Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense.  This patch reimplements
LPM support.

* The new implementation is per-link.  The target policy is still
  port-wide (ap->target_lpm_policy) but all the mechanisms and states
  are per-link and integrate well with the rest of link abstraction
  and can work with slave and PMP links.

* Core EH has proper control of LPM state.  LPM state is reconfigured
  when and only when reconfiguration is necessary.  It makes sure that
  LPM state is reset when probing for new device on the link.
  Controller agnostic logic is now implemented in libata EH proper and
  driver implementation only has to deal with controller specifics.

* Proper error handling.  LPM config failure is attributed to the
  device on the link and LPM is disabled for the link if it fails
  repeatedly.

* ops->enable/disable_pm() are replaced with single ops->set_lpm()
  which takes @policy and @hints.  This simplifies driver specific
  implementation.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Link power management is about to be reimplemented.  Prepare for it.

* Implement sata_link_scr_lpm().

* Drop static from ata_dev_set_feature() and make it available to
  other libata files.

* Trivial whitespace adjustments.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm.  This patch cleans up lpm related symbols
and sysfs show/store functions as follows.

* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
  MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
  ATA_LPM_{MIN|MAX|MED}_POWER.

* Pre/postfixes are unified to lpm.

* sysfs show/store functions for link_power_management_policy were
  curiously named get/put and unnecessarily complex.  Renamed to
  show/store and simplified.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This build error showed up in linux-next tag next-20100820 for ia64:

WARNING: vmlinux.o(.init.text+0x4a952): Section mismatch in reference from the function ata_init() to the function .exit.text:ata_sff_exit()
The function __init ata_init() references
a function __exit ata_sff_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
ata_sff_exit() so it may be used outside an exit section.

Sure enough, dropping the __exit fixes the problem.
Signed-off-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This change enables my x86 machine to recognize and talk to a
"Native 4K" SATA device.

When I started working on this, I didn't know Matthew Wilcox had
posted a similar patch 2 years ago:
  http://git.kernel.org/?p=linux/kernel/git/willy/ata.git;a=shortlog;h=refs/heads/ata-large-sectors

Gwendal Grignou pointed me at the the above code and small portions of
this patch include Matthew's work. That's why Mathew is first on the
"Signed-off-by:". I've NOT included his use of a bitmap to determine
512 vs Native for ATA command block size - just used a simple table.
And bugs are almost certainly mine.

Lastly, the patch has been tested with a native 4K 'Engineering
Sample' drive provided by Hitachi GST.
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: NGrant Grundler <grundler@google.com>
Reviewed-by: NGwendal Grignou <gwendal@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way.  libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.

This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions.  This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.

* sata_fsl: It already builds done_mask.  Conversion is straight
  forward.

* sata_mv: mv_process_crpb_response() no longer checks for illegal
  completions, it just returns whether the tag is completed or not.
  mv_process_crpb_entries() builds done_mask from it and passes it to
  ata_qc_complete_multiple() which will check for illegal completions.

* sata_nv adma: Similar to sata_mv.  nv_adma_check_cpb() now just
  returns the tag status and nv_adma_interrupt() builds done_mask from
  it and passes it to ata_qc_complete_multiple().

* sata_nv swncq: It already builds done_mask.  Drop unnecessary
  illegal transition checks and call ata_qc_complete_multiple().

In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: NGwendal Grignou <gwendal@google.com>
Reviewed-by: NGrant Grundler <grundler@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

libata depends on scsi_host_template for module reference counting and
sht's should be owned by each low level driver.  During libahci split,
the sht was left with libahci.ko leaving the actual low level drivers
not reference counted.  This made ahci and ahci_platform always
unloadable even while they're being actively used.

Fix it by defining AHCI_SHT() macro in ahci.h and defining a sht for
each low level ahci driver.

stable: only applicable to 2.6.35.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NPedro Francisco <pedrogfrancisco@gmail.com>
Tested-by: NMichael Tokarev <mjt@tls.msk.ru>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Keep track of the link on the which the current request is in progress.
It allows support of links behind port multiplier.

Not all libata-sff is PMP compliant. Code for native BMDMA controller
does not take in accound PMP.

Tested on Marvell 7042 and Sil7526.
Signed-off-by: NGwendal Grignou <gwendal@google.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For some mysterious reason, certain hardware reacts badly to usual EH
actions while the system is going for suspend.  As the devices won't
be needed until the system is resumed, ask EH to skip usual autopsy
and recovery and proceed directly to suspend.
Signed-off-by: NTejun Heo <tj@kernel.org>
Tested-by: NStephan Diestelhorst <stephan.diestelhorst@amd.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the Intel Patsburg (PCH) SATA AHCI and RAID Controller
DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds the Intel Patsburg (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 978c0666 (libata: Remove excess delay in the tf_load path)
removed ata_wait_idle() from ata_sff_tf_load() and via_tf_load().
This caused obscure detection problems in sata_sil.

  https://bugzilla.kernel.org/show_bug.cgi?id=16606

The commit was pure performance optimization.  Revert it for now.
Reported-by: NDieter Plaetinck <dieter@plaetinck.be>
Reported-by: NJan Beulich <JBeulich@novell.com>
Bisected-by: Ngianluca <gianluca@sottospazio.it>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ahci_do_softreset() compared the current time and deadline in reverse
when calculating timeout for SRST issue.  The result is that if
@deadline is in future, SRST is issued with 0 timeout, which hasn't
caused any problem because it later waits for DRDY with the correct
timeout.  If deadline is already exceeded by the time SRST is about to
be issued, the timeout calculation underflows and if the device
doesn't respond, timeout doesn't trigger for a _very_ long time.

Reverse the incorrect comparison order.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NAnssi Hannula <anssi.hannula@iki.fi>
Tested-by: NGwendal Grignou <gwendal@google.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

x % 1 always evaluates to 0, which clearly isn't the intent. The
author probably had "% 2" or "& 1" in mind, and mispelled it.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Remove harmful BUG_ON() from ata_bmdma_qc_issue(),
as it casts too wide of a net and breaks sata_mv.
It also crashes the kernel while doing the BUG_ON().

There's already a WARN_ON_ONCE() further down to catch
the case of POLLING for a BMDMA operation.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org

Fix DSM/TRIM commands in sata_mv (v2).
These need to be issued using old-school "BM DMA",
rather than via the EDMA host queue.

Since the chips don't have proper BM DMA status,
we need to be more careful with setting the ATA_DMA_INTR bit,
since DSM/TRIM often has a long delay between "DMA complete"
and "command complete".

GEN_I chips don't have BM DMA, so no TRIM for them.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org

ata_qc_issue() BUG_ON()s on data commands w/o data, which may be
submitted via SG_IO.  Be less of a drama queen and just trigger
WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NStefan Hübner <stefan.huebner@stud.tu-ilmenau.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

dma_dwc_xfer_setup() returns an int and "dma_chan" needs to be signed
for the error handling to work.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP
in PORT_CMD.  Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.

Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit d62f5576 (pata_cmd64x: fix handling of address setup timings)
incorrectly called ata_timing_compute() on UDMA mode on 0 @UT leading
to devide by zero fault.  Revert it until better fix is available.
This is reported in bko#16607 by Milan Kocian who also root caused it.

  https://bugzilla.kernel.org/show_bug.cgi?id=16607Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-and-root-caused-by: NMilan Kocian <milan.kocian@wq.cz>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Some minor improvements in error handling, but overall it was mostly dead
code.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

'make htmldocs' has a fatal error when processing libata.xml, as seen
below.  The string "Example patterns:" (or any string with "example.*:"
in it AFAIK) causes some part of the doc generation tool chain to try to
produce an <informalexample> block without a beginning <para>, but
there is an ending </para> generated, which throws things out of kilter.

I don't even know where (what program) this is happening in.
I searched in docproc and xmlto and in some XML stylesheets without
finding anything.  If anyone can give me pointers about this, please do.
Until this is fixed, let's just spell "Example" as "Sample"
and match up the double quotation marks while there.

  Documentation/DocBook/libata.xml:6575: parser error : Opening and ending tag mismatch: programlisting line 6573 and para
     </para><para>
            ^
  Documentation/DocBook/libata.xml:6580: parser error : Opening and ending tag mismatch: para line 6575 and programlisting
  </programlisting></informalexample>
                   ^
  unable to parse Documentation/DocBook/libata.xml
  make[2]: *** [Documentation/DocBook/libata.html] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver.  There were two flags in the bio that were
missing in the requests:  BIO_RW_UNPLUG and BIO_RW_AHEAD.  Also I've
renamed two request flags that had a superflous RW in them.

Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests.  This allows much easier grepping for different request
types instead of unwinding through macros.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

of_device is just an alias for platform_device, so remove it entirely.  Also
replace to_of_device() with to_platform_device() and update comment blocks.

This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.

@@
@@
-struct of_device
+struct platform_device
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Reviewed-by: NDavid S. Miller <davem@davemloft.net>

Instead of io_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[0,1] for up to two ioport
ranges. After a call to pcmcia_request_io(), the ports found there
are reserved, after calling pcmcia_request_configuration(), they may
be used.

CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

After pcmcia_request_io(), do not make use of the values stored in
io_req_t, but instead use those found in struct pcmcia_device->resource[].

CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Make the following changes to prepare for NCQ command completion
update.  Changes made by this patch don't cause any functional
difference.

* sata_fsl_host_intr(): rename the local variable qc_active to
  done_mask as that's what it is.

* mv_process_crpb_response(): restructure if clause for easier update.

* nv_adma_interrupt(): drop unnecessary error variable.

* nv_swncq_sdbfis(): drop unnecessary nr_done and return 0 on success.
  Typo fix.

* nv_swncq_dmafis(): drop unused return value and return void.

* nv_swncq_host_interrupt(): drop unnecessary return value handling.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

SIDPR window registers are shared across ports and as each access is
done in two steps, accesses to different ports under EH may race.
This primarily is caused by incorrect host locking in EH context and
should be fixed by defining locking requirements for each EH operation
which can be used during EH and enforcing them but for now work around
the problem by adding a dedicated SIDPR lock and grabbing it for each
SIDPR access.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NMark Knecht <markknecht@gmail.com>
Reported-by: NPaul Check <paul@thechecks.ca>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Take further advantage of the new glob_match() function to reduce
the blacklist size, this time making use of "character ranges" in
the patterns.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Enable use of hyphenated pattern ranges in glob_match(), similar to how
shell globbing works, and how developers might expect things to work.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 1529c69a (ata_generic: implement ATA_GEN_* flags and force
enable DMA on MBP 7,1) implemented ATA_GEN_FORCE_DMA for forcing DMA
mode and applied it to CENATEK but forgot to remove the original hard
coded logic.  This is removal of redundant logic and doesn't affect
correctness.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The below patch casts ATA_MAX_QUEUE to int because GCC will
give a warning message about the two different enum blocks:
  CC      drivers/ata/ahci.o
drivers/ata/ahci.c: In function 'ahci_init_one':
drivers/ata/ahci.c:1045:2: warning: comparison between 'enum <anonymous>' and 'enum <anonymous>'
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Adds support for the Samsung PATA controller. This driver is based
on the Libata subsystem and references the earlier patches sent for
IDE subsystem.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: NSergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>